Millimetre-Resolution Photonics-Assisted Radar

Radar is essential in applications such as anti-collision systems for driving, airport security screening, and contactless vital sign detection. The demand for high-resolution and real-time recognition in radar applications is growing, driving the development of electronic radars with increased bandwidth, higher frequency, and improved reconfigurability. However, conventional electronic approaches are challenging due to limitations in synthesising radar signals, limiting performance. In contrast, microwave photonics-enabled radars have gained interest because they offer numerous benefits compared to traditional electronic methods. Photonics-assisted techniques provide a broad fractional bandwidth at the optical carrier frequency and enable spectrum manipulation, producing wideband and high-resolution radar signals in various formats. However, photonic-based methods face limitations like low time-frequency linearity due to the inherent nonlinearity of lasers, restricted RF bandwidth, limited stability of the photonic frequency multipliers, and difficulties in achieving extended sensing with dispersion-based techniques. In response to these challenges, this thesis presents approaches for generating broadband radar signals with high time-frequency linearity using recirculated unidirectional optical frequency-shifted modulation. The photonics-assisted system allows flexible bandwidth tuning from sub-GHz to over 30 GHz and requires only MHz-level electronics. Such a system offers millimetre-level range resolution and a high imaging refresh rate, detecting fast-moving objects using the ISAR technique. With millimetre-level resolution and micrometre accuracy, this system supports contactless vital sign detection, capturing precise respiratory patterns from simulators and a living body using a cane toad. In the end, we highlight the promise of merging radar and LiDAR, foreshadowing future advancements in sensor fusion for enhanced sensing performance and resilience

Linearization techniques to suppress optical nonlinearity

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This thesis is shown the implementation of the linearization techniques such as feedforward and pre-distortion feedback linearization to suppress the optical components nonlinearities caused by the fibre and semiconductor optical amplifier (SOA). The simulation verified these two linearization techniques for single tone direct modulation, two tone indirect modulation and ultra wideband input to the optical fibre. These techniques uses the amplified spontaneously emission (ASE) noise reduction in two loops of SOA by a feed-forward and predistortion linearizer and is shown more than 6dB improvement. Also it investigates linearization for the SOA amplifier to cancel out the third order harmonics or inter-modulation distortion (IMD) or four waves mixing. In this project, more than 20 dB reductions is seen in the spectral re-growth caused by the SOA. Amplifier non-linearity becomes more severe with two strong input channels leading to inter-channel distortion which can completely mask a third adjacent channel. The simulations detailed above were performed utilizing optimum settings for the variable gain, phase and delay components in the error correction loop of the feed forward and Predistortion systems and hence represent the ideal situation of a perfect feed-forward and Predistortion system. Therefore it should be consider that complexity of circuit will increase due to amplitude, phase and delay mismatches in practical design. Also it has describe the compatibility of Software Defined Radio with Hybrid Fibre Radio with simulation model of wired optical networks to be used for future research investigation, based on the star and ring topologies for different modulation schemes, and providing the performance for these configurations

Linearization techniques to suppress optical nonlinearity

This thesis is shown the implementation of the linearization techniques such as feedforward and pre-distortion feedback linearization to suppress the optical components nonlinearities caused by the fibre and semiconductor optical amplifier (SOA). The simulation verified these two linearization techniques for single tone direct modulation, two tone indirect modulation and ultra wideband input to the optical fibre. These techniques uses the amplified spontaneously emission (ASE) noise reduction in two loops of SOA by a feed-forward and predistortion linearizer and is shown more than 6dB improvement. Also it investigates linearization for the SOA amplifier to cancel out the third order harmonics or inter-modulation distortion (IMD) or four waves mixing. In this project, more than 20 dB reductions is seen in the spectral re-growth caused by the SOA. Amplifier non-linearity becomes more severe with two strong input channels leading to inter-channel distortion which can completely mask a third adjacent channel. The simulations detailed above were performed utilizing optimum settings for the variable gain, phase and delay components in the error correction loop of the feed forward and Predistortion systems and hence represent the ideal situation of a perfect feed-forward and Predistortion system. Therefore it should be consider that complexity of circuit will increase due to amplitude, phase and delay mismatches in practical design. Also it has describe the compatibility of Software Defined Radio with Hybrid Fibre Radio with simulation model of wired optical networks to be used for future research investigation, based on the star and ring topologies for different modulation schemes, and providing the performance for these configurations.EThOS - Electronic Theses Online ServiceGBUnited Kingdo

Performance of narrow band internet of things (NBIoT) networks

Narrow Band Internet of Things (NBIoT) is a Low Power Wide Area Network (LPWAN) technology that has been standardised by 3GPP in Release 13 to work in cellular networks [15]. The main characteristics of NBIoT are its extended coverage compared to other cellular technologies such as LTE; its high capacity is due to its narrow channel bandwidth of 180 KHz, which also supports the possibility of these devices having a long battery life of up to 10 years, as well as low device complexity - all of which result in low device costs [2]. NBIoT can be deployed in one of three different options, namely: a) standalone, b) in-band and c) guard band deployment mode. These characteristics of NBIoT makes it very useful in the IoT industry, allowing the technology to be used in a wide range of applications, such as health, smart cities, farming, wireless sensor networks and many more [1] [25]. NBIoT can be used to realise the maximum possible spectral efficiency, thereby increasing the capacity of the network. Penetration of NBIoT in the market has dominated other LPWANs like Sigfox and LoRA, with NBIoT having a technology share of close to 50 percent [31]. This study is aimed at exploring the deployment options of NBIoT and determining how network operators can realise the greatest value for their investment by efficiently utilising their allocated spectrum. The main target is to derive the best parameter combination for deployment of the NBIoT network with acceptable error rates in both the uplink and the downlink. Different characteristics of NBIoT were discussed in this study, and the performance of the various approaches investigated to determine their efficiency in relation to the needs of the IoT industry. The error rates of NBIoT, when used in an existing LTE network, were the main focus of this study. Software simulations were used to compare the different parameter settings to see which options provide the best efficiency and cost trade-offs for structuring an NBIoT network. The results of the tests done in this study showed that the error rates are lower for standalone deployment mode than for in-band mode, which is mainly due to less interference in standalone mode than in in-band mode. The results also show that data transmitted in smaller Transport Block Size (TBS) in the Down Link (DL) has less errors than if it’s transmitted in larger blocks. The results also show that the error rate gets lower as the number of subframe repetition increases in the downlink, which is mainly due to the redundancy in sending the same data multiple times. However in the uplink, the results show that the error rates are comparable when the signal has poor quality

Convergence of packet communications over the evolved mobile networks; signal processing and protocol performance

In this thesis, the convergence of packet communications over the evolved mobile networks is studied. The Long Term Evolution (LTE) process is dominating the Third Generation Partnership Project (3GPP) in order to bring technologies to the markets in the spirit of continuous innovation. The global markets of mobile information services are growing towards the Mobile Information Society. The thesis begins with the principles and theories of the multiple-access transmission schemes, transmitter receiver techniques and signal processing algorithms. Next, packet communications and Internet protocols are referred from the IETF standards with the characteristics of mobile communications in the focus. The mobile network architecture and protocols bind together the evolved packet system of Internet communications to the radio access network technologies. Specifics of the traffic models are shortly visited for their statistical meaning in the radio performance analysis. Radio resource management algorithms and protocols, also procedures, are covered addressing their relevance for the system performance. Throughout these Chapters, the commonalities and differentiators of the WCDMA, WCDMA/HSPA and LTE are covered. The main outcome of the thesis is the performance analysis of the LTE technology beginning from the early discoveries to the analysis of various system features and finally converging to an extensive system analysis campaign. The system performance is analysed with the characteristics of voice over the Internet and best effort traffic of the Internet. These traffic classes represent the majority of the mobile traffic in the converged packet networks, and yet they are simple enough for a fair and generic analysis of technologies. The thesis consists of publications and inventions created by the author that proposed several improvements to the 3G technologies towards the LTE. In the system analysis, the LTE showed by the factor of at least 2.5 to 3 times higher system measures compared to the WCDMA/HSPA reference. The WCDMA/HSPA networks are currently available with over 400 million subscribers and showing increasing growth, in the meanwhile the first LTE roll-outs are scheduled to begin in 2010. Sophisticated 3G LTE mobile devices are expected to appear fluently for all consumer segments in the following years

Optical techniques for broadband in-building networks

Optical fibres, which can easily handle any bandwidth demand, have been rolled out to more than 32 million consumer’s homes and professional buildings worldwide up to 2010. The basic technological and economical challenges of fibre-to-the-home (FTTH) has been solved. The current FTTH technology can now providing baseband Gbit Ethernet and high definition TV services to the gates of homes. Thus, the bottleneck for delivery of broadband services to the end users is shifting from the access network to the in-building network. In the meantime, the need for high-capacity transmission between devices inside the building, e.g. between desktop PC and data services, are also rapidly increase. How to bring high bandwidth to the mobile terminals such as laptops, PDAs or cell phones as well as to the fixed terminals such as desktop PCs and HDTV equipment in an all-in-one network infrastructure is a challenge we are facing. Building on the flexibility of the wireless access networks and the latent vast bandwidth of a fibre infrastructure, radio-over-fibre (RoF) techniques have been proposed as a cost-effective solution to the future integrated broadband services in in-building networks. This thesis investigates techniques to deliver high data rate wireless services via in-building networks: high capacity RoF links employing optical frequency multiplication (OFM) and sub-carrier multiplexing (SCM) techniques, with single- or multi-carrier signal formats. The orthogonal frequency division multiplexing (OFDM) format is investigated for the RoF transmission system, particularly with regard to the optical system nonlinearity. For low-cost short-range optical backbone networks, RoF transmission over large-core diameter plastic optical fibre (POF) links has been studied, including the transmission of the WiMedia-compliant multiband OFDM UWB signal over bandwidth-limited large-core POF as well as a full-duplex bi-directional UWB transmission over POF. In order to improve the functionalities for delivery of wireless services of in-building networks, techniques to introduce flexibility into the network architecture and to create dynamic capacity allocation have been investigated. By employing optical switching techniques based on optical semiconductor amplifiers (SOA), an optically routed RoF system has been studied. The dynamic capacity allocation is addressed by investigating one-dimensional and two-dimensional routing using electrical SCM and optical wavelengths. In addition, next to RoF networking, this thesis explores techniques for wired delivery of baseband high capacity services over POF links by employing a multi-level signal modulation format, in particular discrete multi-tone (DMT) modulation. Transmission of 10 Gbit/s data over 1 mm core diameter PMMA POF links is demonstrated, as a competitor to more expensive fibre solutions such as silica single and multimode fibre. A record transmission rate of more than 40 Gbit/s is presented for POF whose core diameter is comparable with silica multimode fibre. Finally, from the network perspective, the convergence of wired and wireless multi-standard services into a single fibre-based infrastructure has been studied. Techniques have been designed and demonstrated for in-building networks, which can convey both high capacity baseband services and broadband radio frequency (RF) services over a POF backbone link. The multi-standard RoF signals carry different wireless services at different radio frequencies and with different bandwidths, including WiFi, WiMax, UMTS and UWB. System setups to carry them together over the same multimode optical fibre based network have been designed and experimentally shown. All the concepts, designs and system experiments presented in this thesis underline the strong potential of multimode (silica and plastic) optical fibre techniques for the delivery of broadband services to wired and wireless devices in in-building networks, in order to extend to the end user the benefits of the broadband FTTH networks which are being installed and deployed worldwide

Digital ADCs and ultra-wideband RF circuits for energy constrained wireless applications by Denis Clarke Daly.

Thesis (Ph. D.)--Massachusetts Institute of Technology, Dept. of Electrical Engineering and Computer Science, 2009.Cataloged from PDF version of thesis.Includes bibliographical references (p. 173-183).Ongoing advances in semiconductor technology have enabled a multitude of portable, low power devices like cellular phones and wireless sensors. Most recently, as transistor device geometries reach the nanometer scale, transistor characteristics have changed so dramatically that many traditional circuits and architectures are no longer optimal and/or feasible. As a solution, much research has focused on developing 'highly digital' circuits and architectures that are tolerant of the increased leakage, variation and degraded voltage headrooms associated with advanced CMOS processes. This thesis presents several highly digital, mixed-signal circuits and architectures designed for energy constrained wireless applications. First, as a case study, a highly digital, voltage scalable flash ADC is presented. The flash ADC, implemented in 0.18 [mu]m CMOS, leverages redundancy and calibration to achieve robust operation at supply voltages from 0.2 V to 0.9 V. Next, the thesis expands in scope to describe a pulsed, noncoherent ultra-wideband transceiver chipset, implemented in 90 nm CMOS and operating in the 3-to-5 GHz band. The all-digital transmitter employs capacitive combining and pulse shaping in the power amplifier to meet the FCC spectral mask without any off-chip filters. The noncoherent receiver system-on-chip achieves both energy efficiency and high performance by employing simple amplifier and ADC structures combined with extensive digital calibration. Finally, the transceiver chipset is integrated in a complete system for wireless insect flight control.(cont.) Through the use of a flexible PCB and 3D die stacking, the total weight of the electronics is kept to 1 g, within the carrying capacity of an adult Manduca sexta moth. Preliminary wireless flight control of a moth in a wind tunnel is demonstrated.Ph.D

Performance analysis of OFDM technology on radio-over-fiber systems

Dissertação de mest., Engenharia Eletrónica e Telecomunicações, Faculdade de Ciências e Tecnologia, Univ. do Algarve, 2011Nowadays, the demand for high speed, high quality and diversity in distributed services presents a challenge for telecommunication technology. Wireless systems provide the accessibility to end-user, but are not the solution for long distance links. Currently, the ideal technology for long-range transmissions at high data rates is optical fiber. Hence, a new concept for high capacity networks emerges, with centralized services into Base Stations (BS) engineered to provide flexibility and control over the system, and to perform operations such as electrical to optical domain conversion and modulation. Such Radio-over-Fiber (RoF) networks also appear as an attractive technology because they are efficient and cost effective. Orthogonal Frequency Division Multiplexing (OFDM) technology is widely used in a number of standards. For instance, it is actually the Multi-Carrier Modulation (MCM) technique applied in 802.11a/g/n wireless standards and in Digital Video Broadcasting-Terrestrial (DVB-T), among other prevailing systems, which makes this subject one particularly pertinent to study. OFDM systems are an appealing choice for waveform modulation, as they are very bandwidth efficient comparing to others MCM, and provide flexibility in data transmission rates. Additionally, an important advantage dwells in its natural robustness against severely interfering environments. In this thesis, fundamentals on OFDM technology are extensively described, and its application to wireless and optical fiber networks is introduced. The combined channel effects of these technologies on OFDM signals are investigated. In terms of performance analysis, this exposition focuses on understanding the importance of OFDM modulation parameters, and explores some OFDM signal properties. To achieve this, a simulator was implemented with Matlab to create arbitrary OFDM waveforms and emulate channel effects. This study also investigates the efficiency of OFDM technology over a real Radio Frequency (RF) system with an ideal communication channel. Finally, an experimental RoF configuration is implemented and its performance is assessed