A 1.2-V 10- µW NPN-Based Temperature Sensor in 65-nm CMOS With an Inaccuracy of 0.2 °C (3σ) From 70 °C to 125 °C

An NPN-based temperature sensor with digital output transistors has been realized in a 65-nm CMOS process. It achieves a batch-calibrated inaccuracy of ±0.5 ◦C (3¾) and a trimmed inaccuracy of ±0.2 ◦C (3¾) over the temperature range from −70 ◦C to 125 ◦C. This performance is obtained by the use of NPN transistors as sensing elements, the use of dynamic techniques, i.e. correlated double sampling and dynamic element matching, and a single room-temperature trim. The sensor draws 8.3 μA from a 1.2-V supply and occupies an area of 0.1 mm2

A simple bandgap reference based on VGO extraction with single-temperature trimming

Bandgap references are widely used in analog and mixed-signal systems to provide temperature-independent voltage or current reference. In traditional bandgap structure, the base-emitter voltage VBE of a diode is used to generate a complementary to absolute temperature (CTAT) voltage, which reduces as temperature increases. The base-emitter voltage difference ∆VBE between two diodes with the same current but different emitter areas supplies a proportional to absolute temperature (PTAT) voltage. With the proper adjustment of the coefficients of VBE and ∆VBE in a voltage summer, the temperature dependency of the summed voltage can be mostly canceled out and the output voltage can achieve a relative temperature-constant property. However, even though the linear terms of temperature-dependent components in PTAT and CTAT expressions can be canceled out, there are still some high order terms left, which still affect temperature dependency. For this reason, a first-order bandgap reference with only PTAT and CTAT linear term compensation cannot achieve a sufficiently low temperature coefficient (TC), normally ranging from 10ppm/°C to over 100ppm/°C. To achieve higher precision and lower TC, the high order terms also need to be considered and compensated by some techniques. This thesis study describes the development of a high order bandgap structure, including the initial thinking, design flow, equation derivation, circuit implementation, and simulation result

Bandgap Reference Design at the 14-Nanometer FinFET Node

As supply voltages continue to decrease, it becomes harder to ensure that the voltage drop across a diode-connected BJT is sufficient to conduct current without sacrificing die area. One such solution to this potential problem is the diode-connected MOSFET operating in weak inversion. In addition to conducting appreciable current at voltages significantly lower than the power supply, the diode-connected MOSFET reduces the total area for the bandgap implementation. Reference voltage variations across Monte Carlo perturbations are more pronounced as the variation of process parameters are exponentially affected in subthreshold conduction. In order for this proposed solution to be feasible, a design methodology was introduced to mitigate the effects of process variation. A 14 nm bandgap reference was created and simulated across Monte Carlo perturbations for 100 runs at nominal supply voltage and 10% variation of the power supply in either direction. The best case reference voltage was found and used to verify the proposed resistive network solution. The average temperature coefficient was measured to be 66.46 ppm/◦C and the voltage adjustment range was found to be 204.1 mV. The two FinFET subthreshold diodes consume approximately 2.8% of the area of the BJT diode equivalent. Utilizing an appropriate process control technique, subthreshold bandgap references have the potential to overtake traditional BJT-based bandgap architectures in low-power, limited-area applications

Design of Analog CMOS Circuits for Batteryless Implantable Telemetry Systems

A wireless biomedical telemetry system is a device that collects biomedical signal measurements and transmits data through wireless RF communication. Testing medical treatments often involves experimentation on small laboratory animals, such as genetically modified mice and rats. Using batteries as a power source results in many practical issues, such as increased size of the implant and limited operating lifetime. Wireless power harvesting for implantable biomedical devices removes the need for batteries integrated into the implant. This will reduce device size and remove the need for surgical replacement due to battery depletion. Resonant inductive coupling achieves wireless power transfer in a manner modelled by a step down transformer. With this methodology, power harvesting for an implantable device is realized with the use of a large primary coil external to the subject, and a smaller secondary coil integrated into the implant. The signal received from the secondary coil must be regulated to provide a stable direct current (DC) power supply, which will be used to power the electronics in the implantable device. The focus of this work is on development of an electronic front-end for wireless powering of an implantable biomedical device. The energy harvesting front-end circuit is comprised of a rectifier, LDO regulator, and a temperature insensitive voltage reference. Physical design of the front-end circuit is developed in 0.13um CMOS technology with careful attention to analog layout issues. Post-layout simulation results are presented for each sub-block as well as the full front-end structure. The LDO regulator operates with supply voltages in the range of 1V to 1.5V with quiescent current of 10.5uA The complete power receiver front-end has a power conversion efficiency of up to 29%

Ultra-low power mixed-signal frontend for wearable EEGs

Electronics circuits are ubiquitous in daily life, aided by advancements in the chip design industry, leading to miniaturised solutions for typical day to day problems. One of the critical healthcare areas helped by this advancement in technology is electroencephalography (EEG). EEG is a non-invasive method of tracking a person's brain waves, and a crucial tool in several healthcare contexts, including epilepsy and sleep disorders. Current ambulatory EEG systems still suffer from limitations that affect their usability. Furthermore, many patients admitted to emergency departments (ED) for a neurological disorder like altered mental status or seizures, would remain undiagnosed hours to days after admission, which leads to an elevated rate of death compared to other conditions. Conducting a thorough EEG monitoring in early-stage could prevent further damage to the brain and avoid high mortality. But lack of portability and ease of access results in a long wait time for the prescribed patients. All real signals are analogue in nature, including brainwaves sensed by EEG systems. For converting the EEG signal into digital for further processing, a truly wearable EEG has to have an analogue mixed-signal front-end (AFE). This research aims to define the specifications for building a custom AFE for the EEG recording and use that to review the suitability of the architectures available in the literature. Another critical task is to provide new architectures that can meet the developed specifications for EEG monitoring and can be used in epilepsy diagnosis, sleep monitoring, drowsiness detection and depression study. The thesis starts with a preview on EEG technology and available methods of brainwaves recording. It further expands to design requirements for the AFE, with a discussion about critical issues that need resolving. Three new continuous-time capacitive feedback chopped amplifier designs are proposed. A novel calibration loop for setting the accurate value for a pseudo-resistor, which is a crucial block in the proposed topology, is also discussed. This pseudoresistor calibration loop achieved the resistor variation of under 8.25%. The thesis also presents a new design of a curvature corrected bandgap, as well as a novel DDA based fourth-order Sallen-Key filter. A modified sensor frontend architecture is then proposed, along with a detailed analysis of its implementation. Measurement results of the AFE are finally presented. The AFE consumed a total power of 3.2A (including ADC, amplifier, filter, and current generation circuitry) with the overall integrated input-referred noise of 0.87V-rms in the frequency band of 0.5-50Hz. Measurement results confirmed that only the proposed AFE achieved all defined specifications for the wearable EEG system with the smallest power consumption than state-of-art architectures that meet few but not all specifications. The AFE also achieved a CMRR of 131.62dB, which is higher than any studied architectures.Open Acces

Frequency stabilization of an ultraviolet semiconductor disk laser

We report a tunable, narrow-linewidth UV laser based on intracavity second-harmonic generation in a red semiconductor disk laser. Single-frequency operation is demonstrated with a total UV output power of 26 mW. By servo-locking the fundamental frequency to a reference Fabry–Pérot cavity, the linewidth of the UV beam has been reduced to 16 kHz on short timescales and 50 kHz on a 1 s timescale, relative to the reference

Quantum transport in carbon nanotubes

Carbon nanotubes are a versatile material in which many aspects of condensed matter physics come together. Recent discoveries, enabled by sophisticated fabrication, have uncovered new phenomena that completely change our understanding of transport in these devices, especially the role of the spin and valley degrees of freedom. This review describes the modern understanding of transport through nanotube devices. Unlike conventional semiconductors, electrons in nanotubes have two angular momentum quantum numbers, arising from spin and from valley freedom. We focus on the interplay between the two. In single quantum dots defined in short lengths of nanotube, the energy levels associated with each degree of freedom, and the spin-orbit coupling between them, are revealed by Coulomb blockade spectroscopy. In double quantum dots, the combination of quantum numbers modifies the selection rules of Pauli blockade. This can be exploited to read out spin and valley qubits, and to measure the decay of these states through coupling to nuclear spins and phonons. A second unique property of carbon nanotubes is that the combination of valley freedom and electron-electron interactions in one dimension strongly modifies their transport behaviour. Interaction between electrons inside and outside a quantum dot is manifested in SU(4) Kondo behavior and level renormalization. Interaction within a dot leads to Wigner molecules and more complex correlated states. This review takes an experimental perspective informed by recent advances in theory. As well as the well-understood overall picture, we also state clearly open questions for the field. These advances position nanotubes as a leading system for the study of spin and valley physics in one dimension where electronic disorder and hyperfine interaction can both be reduced to a very low level.Comment: In press at Reviews of Modern Physics. 68 pages, 55 figure

A phase-locked frequency divide-by-3 optical parametric oscillator

Accurate phase-locked 3:1 division of an optical frequency was achieved, by using a continuous-wave (cw) doubly resonant optical parametric oscillator. A fractional frequency stability of 2*10^(-17) of the division process has been achieved for 100s integration time. The technique developed in this work can be generalized to the accurate phase and frequency control of any cw optical parametric oscillator.Comment: 4 pages, 5 figures in a postscript file. To appear in a special issue of IEEE Trans. Instr. & Meas., paper FRIA-2 presented at CPEM'2000 conference, Sydney, May 200

Investigation, Analysis and Design of a Sub-Bandgap Voltage Reference for Ultra-Low Voltage Applications

The purpose of this thesis is to study and fully comprehend how to realize a very high performance sub-bandgap (low-voltage) structure. Physics of semiconductor devices has been analyzed before beginning the design of the voltage reference itself. New formulas, as practical as accurate, will be derived. Parallel to this design activity, it was possible to study an already developed sub-bandgap structure, comparing measurements to simulation results. Layout and extracted simulations have also been taken into accoun

Low Power, High PSR CMOS Voltage References

With integration of various functional modules such as radio frequency (RF) circuits, power management, and high frequency digital and analog circuits into one system on chip (SoC) in recent applications, power supply noise can cause significant system performance deterioration. This makes supply noise rejection of the embedded voltage reference crucial in modern SoC applications. Also the use of resistors in bandgap voltage references makes them less suitable for modern low power and portable applications. This thesis introduces two resistorless sub-1 V, all MOSFET references. The goal is to achieve a high power supply rejection (PSR) over a wide bandwidth not achieved in previous works. This high PSR over wide bandwidth is achieved by using a combination of a feedback technique and an innovative compact MOSFET low pass filter. The two references were fabricated in a standard 0.18 µm CMOS process. The first reference uses a composite transistor in subthreshold to produce a proportional-to-absolute temperature (PTAT) voltage which is converted to a current used to thermally compensate the threshold voltage of a MOSFET in saturation. The second references uses dynamic-threshold voltage MOSFET (DTMOS) to produce a PTAT voltage which is converted to a current used to thermally compensate the threshold voltage of a MOSFET in saturation. The measurement shows that both references consumes a sub-1 µW power across their entire operating temperatures. The first reference achieves a PSR better than 50 dB for frequencies of up to 70 MHz and a 20 ppm/°C temperature coefficient (TC) for temperatures from -35 °C — 80 °C. It has a compact area of 0.0180 mm2 and operates on a supply of 1.2 V — 2.3 V. The second reference achieves a PSR better than 50 dB for frequencies of up to 60 MHz. This reference achieves a TC of 9.33 ppm/°C after trimming for temperatures from -30 °C — 110 °C and a line regulation of 0.076 %/V for a step from 0.8 V to 2 V supply voltage with 360 nW power consumption at room temperature. It has a compact area of 0.0143 mm^2