Influence of Fluid-Structure Interaction on Microcantilever Vibrations: Applications to Rheological Fluid Measurement and Chemical Detection

At the microscale, cantilever vibrations depend not only on the microstructure’s properties and geometry but also on the properties of the surrounding medium. In fact, when a microcantilever vibrates in a fluid, the fluid offers resistance to the motion of the beam. The study of the influence of the hydrodynamic force on the microcantilever’s vibrational spectrum can be used to either (1) optimize the use of microcantilevers for chemical detection in liquid media or (2) extract the mechanical properties of the fluid. The classical method for application (1) in gas is to operate the microcantilever in the dynamic transverse bending mode for chemical detection. However, the performance of microcantilevers excited in this standard out-of-plane dynamic mode drastically decreases in viscous liquid media. When immersed in liquids, in order to limit the decrease of both the resonant frequency and the quality factor, alternative vibration modes that primarily shear the fluid (rather than involving motion normal to the fluid/beam interface) have been studied and tested: these include inplane vibration modes (lateral bending mode and elongation mode). For application (2), the classical method to measure the rheological properties of fluids is to use a rheometer. To overcome the limitations of this classical method, an alternative method based on the use of silicon microcantilevers is presented. The method, which is based on the use of analytical equations for the hydrodynamic force, permits the measurement of the complex shear modulus of viscoelastic fluids over a wide frequency range

Densely distributed and real-time scour hole monitoring using piezoelectric rod sensors

This study aims to validate a piezoelectric driven-rod scour monitoring system that can sense changes in scour depth along the entire rod at its instrumented location. The proposed sensor is a polymeric slender rod with a thin strip of polyvinylidene fluoride that runs through its midline. Extraction of the fundamental frequency allows the direct calculation of the exposed length (or scour depth) of the slender rod undergoing fluid flow excitation. First, laboratory validation in dry conditions is presented. Second, hydrodynamic testing of the sensor system in a soil-bed flume is discussed. Each rod was installed using a three-dimensional-printed footing designed for ease of installation and stabilization during testing. The sensors were installed in a layout designed to capture symmetric scour conditions around a scaled pier. In order to analyze the system out of steady-state conditions, water velocity was increased in stages during testing to induce different degrees of scour. As ambient water flow excited the portion of the exposed rods, the embedded piezoelectric element outputted a time-varying voltage signal. Different methods were then employed to extract the fundamental frequency of each rod, and the results were compared. Further testing was also performed to characterize the relationship between frequency outputs and flow velocity, which were previously thought to be independent. In general, the proposed driven-rod scour monitoring system successfully captured changing frequencies under varied flow conditions

Effect of Hydrodynamic Force on Microcantilever Vibrations: Applications to Liquid-Phase Chemical Sensing

At the microscale, cantilever vibrations depend not only on the microstructure’s properties and geometry but also on the properties of the surrounding medium. In fact, when a microcantilever vibrates in a fluid, the fluid offers resistance to the motion of the beam. The study of the influence of the hydrodynamic force on the microcantilever’s vibrational spectrum can be used to either (1) optimize the use of microcantilevers for chemical detection in liquid media or (2) extract the mechanical properties of the fluid. The classical method for application (1) in gas is to operate the microcantilever in the dynamic transverse bending mode for chemical detection. However, the performance of microcantilevers excited in this standard out-of-plane dynamic mode drastically decreases in viscous liquid media. When immersed in liquids, in order to limit the decrease of both the resonant frequency and the quality factor, and improve sensitivity in sensing applications, alternative vibration modes that primarily shear the fluid (rather than involving motion normal to the fluid/beam interface) have been studied and tested: these include in-plane vibration modes (lateral bending mode and elongation mode). For application (2), the classical method to measure the rheological properties of fluids is to use a rheometer. However, such systems require sampling (no in-situ measurements) and a relatively large sample volume (a few milliliters). Moreover, the frequency range is limited to low frequencies (less than 200Hz). To overcome the limitations of this classical method, an alternative method based on the use of silicon microcantilevers is presented. The method, which is based on the use of analytical equations for the hydrodynamic force, permits the measurement of the complex shear modulus of viscoelastic fluids over a wide frequency range

The Mercury-Redstone project

Mercury-Redstone project development history, and contributions to future manned spacecraft design and operatio

Lateral-Mode Vibration of Microcantilever-Based Sensors in Viscous Fluids Using Timoshenko Beam Theory

To more accurately model microcantilever resonant behavior in liquids and to improve lateral-mode sensor performance, a new model is developed to incorporate viscous fluid effects and Timoshenko beam effects (shear deformation, rotatory inertia). The model is motivated by studies showing that the most promising geometries for lateral-mode sensing are those for which Timoshenko effects are most pronounced. Analytical solutions for beam response due to harmonic tip force and electrothermal loadings are expressed in terms of total and bending displacements, which correspond to laser and piezoresistive readouts, respectively. The influence of shear deformation, rotatory inertia, fluid properties, and actuation/detection schemes on resonant frequencies ( ) and quality factors ( ) are examined, showing that Timoshenko beam effects may reduce and by up to 40% and 23%, respectively, but are negligible for width-to-length ratios of 1/10 and lower. Comparisons with measurements (in water) indicate that the model predicts the qualitative data trends, but underestimates the softening that occurs in stiffer specimens, indicating that support deformation becomes a factor. For thinner specimens, the model estimates quite well, but exceeds the observed values for thicker specimens, showing that the Stokes resistance model employed should be extended to include pressure effects for these geometries.[2014-0157

Thermal Excitation and Piezoresistive Detection of Cantilever In-Plane Resonance Modes for Sensing Applications

Thermally excited and piezoresistively detected bulk-micromachined cantilevers vibrating in their in-plane flexural resonance mode are presented. By shearing the surrounding fluid rather than exerting normal stress on it, the in-plane mode cantilevers exhibit reduced added fluid mass effects and improved quality factors in a fluid environment. In this letter, different cantilever geometries with in-plane resonance frequencies from 50 kHz to 2.2 MHz have been tested, with quality factors as high as 4200 in air and 67 in water

Self-noise produced by an airfoil with nonflat plate trailing-edge serrations

This paper represents the results of an experimental study aimed at reducing the airfoil self-noise by the trailing edge serration of four different sawtooth geometries (defined in the serration angle and length). These serrations have a common feature: all of the sawtooth patterns are cut directly into the trailing edge of a realistic airfoil. This configuration offers better structural strength and integrity. For the sawtooth trailing edges investigated here, the radiation of the extraneous vortex shedding noise in a narrowband frequency due to the partial bluntness at the serration roots is unavoidable. However, this narrowband component tends to be less significant provided that the serration angle is large and the serration length is moderate. Sound power was measured, and some of the sawtooth geometries have been shown to afford significant boundary-layer instability tonal noise and moderate turbulent broadband noise reductions across a fairly large velocity range. This paper demonstrates that a nonflat plate serrated trailing edge can also be effective in the self-noise reduction. Some experimental results are also presented in order to explain the self-noise mechanisms.This work is partly supported by the Brunel Research Initiative and Enterprise fun

Optimal control of the heave motion of marine cable subsea-unit systems

One of the key problems associated with subsea operations involving tethered subsea units is the motions of support vessels on the ocean surface which can be transmitted to the subsea unit through the cable and increase the tension. In this paper, a theoretical approach for heave compensation is developed. After proper modelling of each element of the system, which includes the cable/subsea-unit, the onboard winch, control theory is applied to design an optimal control law. Numerical simulations are carried out, and it is found that the proposed active control scheme appears to be a promising solution to the problem of heave compensation

Integrating microfluidics and biosensing on a single flexible acoustic device using hybrid modes

Integration of microfluidics and biosensing functionalities on a single device holds promise in continuous health monitoring and disease diagnosis for point-of-care applications. However, the required functions of fluid handling and biomolecular sensing usually arise from different actuation mechanisms. In this work, we demonstrate that a single acoustofluidic device, based on a flexible thin film platform, is able to generate hybrid waves modes, which can be used for fluidic actuation (Lamb waves) and biosensing (thickness shear waves). On this integrated platform, we show multiple and sequential functions of mixing, transport and disposal of liquid volumes using Lamb waves, whilst the thickness bulk shear waves allow us to sense the chemotherapeutic Imatinib, using an aptamer-based strategy, as would be required for therapy monitoring. Upon binding, the conformation of the aptamer results in a change in coupled mass, which has been detected. This platform architecture has the potential to generate a wide range of simple sample-to-answer biosensing acoustofluidic devices