A 0.1-to-1.2GHz tunable 6th-order N-path channel-select filter with 0.6dB passband ripple and +7dBm blocker tolerance

Radio receivers should be robust to large out-of-band blockers with small degradation in their sensitivity. N-path mixers can be used as mixer-first receivers [1] with good linearity and RF filtering [2]. However, 1/f noise calls for large active device sizes for IF circuits and high power consumption. The 1/f noise issue can be relaxed by having RF gain. However, to avoid desensitization by large out-of-band blockers, a bandpass filter (BPF) with sharp cut-off frequency is required in front of the RF amplifiers. gm-C BPFs suffer from tight tradeoffs among DR, power consumption, Q and fc. Also, on-chip Q-enhanced LC BPFs [3] are not suitable due to low DR, large area and non-tunability. Therefore, bulky and non-tunable SAW filters are used. N-path BPFs offer high Q while their center frequency is tuned by the clock frequency [2]. Compared to gm-C filters, this technique decouples the required Q from the DR. The 4-path filter in [4] has only 2nd-order filtering and limited rejection. The order and rejection of N-path BPFs can be increased by cascading [5], but this renders a “round” passband shape. The 4th-order 4-path BPF in [6] has a “flat” passband shape and high rejection but a high NF. This work solves the noise issue of [6] while achieving the same out-of-band linearity and adding 25dB of voltage gain to relax the noise requirement of the subsequent stages

A receiver with in-band IIP3>20dBm, exploiting cancelling of OpAmp finite-gain-induced distortion via negative conductance

Highly linear CMOS radio receivers increasingly exploit linear RF V-I conversion and passive down-mixing, followed by an OpAmp based Transimpedance Amplifier at baseband. Due to the finite OpAmp gain in wideband receivers operating with large signals, virtual ground is imperfect, inducing distortion currents. We propose to apply a negative conductance to cancel this distortion. In an RF receiver, this increases In-Band IIP3 from 9dBm to >20dBm, at the cost of 1.5dB extra NF and <10% power penalty. In 1MHz bandwidth, a Spurious-Free Dynamic Range of 85dB is achieved at <27mA up to 2GHz for 1.2V supply voltage

Cancellation of OpAmp virtual ground imperfections by a negative conductance applied to improve RF receiver linearity

High linearity CMOS radio receivers often exploit linear V-I conversion at RF, followed by passive down-mixing and an OpAmp-based Transimpedance Amplifier at baseband. Due to nonlinearity and finite gain in the OpAmp, virtual ground is imperfect, inducing distortion currents. This paper proposes a negative conductance concept to cancel such distortion currents. Through a simple intuitive analysis, the basic operation of the technique is explained. By mathematical analysis the optimum negative conductance value is derived and related to feedback theory. In- and out-of-band linearity, stability and Noise Figure are also analyzed. The technique is applied to linearize an RF receiver, and a prototype is implemented in 65 nm technology. Measurement results show an increase of in-band IIP3 from 9dBm to >20dBm, and IIP2 from 51 to 61dBm, at the cost of increasing the noise figure from 6 to 7.5dB and <10% power penalty. In 1MHz bandwidth, a Spurious-Free Dynamic Range of 85dB is achieved at <27mA up to 2GHz for 1.2V supply voltage

A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

Integrated Circuit and System Design for Cognitive Radio and Ultra-Low Power Applications

The ubiquitous presence of wireless and battery-powered devices is an inseparable and invincible feature of our modern life. Meanwhile, the spectrum aggregation, and limited battery capacity of handheld devices challenge the exploding demand and growth of such radio systems. In this work, we try to present two separate solutions for each case; an ultra-wideband (UWB) receiver for Cognitive Radio (CR) applications to deal with spectrum aggregation, and an ultra-low power (ULP) receiver to enhance battery life of handheld wireless devices. Limited linearity and LO harmonics mixing are two major issues that ultra-wideband receivers, and CR in particular, are dealing with. Direct conversion schemes, based on current-driven passive mixers, have shown to improve the linearity, but unable to resolve LO harmonic mixing problem. They are usually limited to 3rd, and 5th harmonics rejection or require very complex and power hungry circuitry for higher number of harmonics. This work presents a heterodyne up-down conversion scheme in 180 nm CMOS technology for CR applications (54-862 MHz band) that mitigates the harmonic mixing issue for all the harmonics, while by employing an active feedback loop, a comparable to the state-of-the art IIP3 of better than +10 dBm is achieved. Measurements show an average NF of 7.5 dB when the active feedback loop is off (i.e. in the absence of destructive interference), and 15.5 dB when the feedback loop is active and a 0 dBm interferer is applied, respectively. Also, the second part of this work presents an ultra-low power super-regenerative receiver (SRR) suitable for OOK modulation and provides analytical insight into its design procedure. The receiver is fabricated in 40 nm CMOS technology and operates in the ISM band of 902-928 MHz. Binary search algorithm through Successive Approximation Register (SAR) architecture is being exploited to calibrate the internally generated quench signal and the working frequency of the receiver. Employing an on-chip inductor and a single-ended to differential architecture for the input amplifier has made the receiver fully integrable, eliminating the need for external components. A power consumption of 320 µW from a 0.65 V supply results in an excellent energy efficiency of 80 pJ/b at 4 Mb/s data rate. The receiver also employs an ADC that enables soft-decisioning and a convenient sensitivity-data rate trade-off, achieving sensitivity of -86.5, and -101.5 dBm at 1000 and 31.25 kbps data rate, respectivel

RF Frontend for Spectrum Analysis in Cognitive Radio

Advances in wireless technology have sparked a plethora of mobile communication standards to support a variety of applications. FCC predicts a looming crisis due to the exponentially growing demand for spectrum and it recommends to increase the efficiency of spectrum utilization. Cognitive Radio (CR) is envisioned as a radio technology which detects and exploits empty spectrum to improve the quality of communication. Spectrum analyzer for detecting spectrum holes is a key component required for implementing cognitive radio. Mitola's vision of using an RF Analog-to-Digital (ADC) to digitize the entire spectrum is not yet a reality. The traditional spectrum analysis technique based on a RF Front end using an LO Sweep is too slow, making it unsuitable to track fast hopping signals. In this work, we demonstrate an RF Frontend that can simplify the ADC's requirement by splitting the input spectrum into multiple channels. It avoids the problem of PLL settling by incorporating LO synthesis within the signal path using a concept called Iterative Down Converter. An example 0.75GHz-11.25GHz RF Channelizer is designed in 65nm Standard CMOS Process. The channelizer splits the input spectrum (10.5GHz bandwidth) into seven channels (each of bandwidth 1.5GHz). The channelizer shows the ability to rapidly switch from one channel to another (within a few ns) as well as down-converting multiple channels simultaneously (concurrency). The channelizer achieves a dynamic range of 54dB for a bandwidth of 10.5GHz, while consuming 540mW of power. Harmonic rejection mixer plays a key role in a broadband receiver. A novel order scalable harmonic rejection mixer architecture is described in this research. A proof-of-principle prototype has been designed and fabricated in a 45nm SOI technology. Experimental results demonstrate an operation range of 0.5GHz to 1.5GHz for the LO frequency while offering harmonic rejection better than 55dB for the 3rd harmonic and 58dB for the 5th harmonic across LO frequencies. While cognitive radio solves the spectrum efficiency problem in frequency domain, the electronic beam steering provides a spatial domain solution. Electronic beam forming using phased arrays have been claimed to improve spectrum efficiency by serving more number of users for a given bandwidth. A LO path phase-shifter with frequency-doubling is demonstrated for WiMAX applications

Advances in Integrated Circuit Design and Implementation for New Generation of Wireless Transceivers

User’s everyday outgrowing demand for high-data and high performance mobile devices pushes industry and researchers into more sophisticated systems to fulfill those expectations. Besides new modulation techniques and new system designs, significant improvement is required in the transceiver building blocks to handle higher data rates with reasonable power efficiency. In this research the challenges and solution to improve the performance of wireless communication transceivers is addressed. The building block that determines the efficiency and battery life of the entire mobile handset is the power amplifier. Modulations with large peak to average power ratio severely degrade efficiency in the conventional fixed-biased power amplifiers (PAs). To address this challenge, a novel PA is proposed with an adaptive load for the PA to improve efficiency. A nonlinearity cancellation technique is also proposed to improve linearity of the PA to satisfy the EVM and ACLR specifications. Ultra wide-band (UWB) systems are attractive due to their ability for high data rate, and low power consumption. In spite of the limitation assigned by the FCC, the coexistence of UWB and NB systems are still an unsolved challenge. One of the systems that is majorly affected by the UWB signal, is the 802.11a system (5 GHz Wi-Fi). A new analog solution is proposed to minimize the interference level caused by the impulse Radio UWB transmitter to nearby narrowband receivers. An efficient 400 Mpulse/s IR-UWB transmitter is implemented that generates an analog UWB pulse with in-band notch that covers the majority of the UWB spectrum. The challenge in receiver (RX) design is the over increasing out of blockers in applications such as cognitive and software defined radios, which are required to tolerate stronger out-of-band (OB) blockers. A novel RX is proposed with a shunt N-path high-Q filter at the LNA input to attenuate OB-blockers. To further improve the linearity, a novel baseband blocker filtering techniques is proposed. A new TIA has been designed to maintain the good linearity performance for blockers at large frequency offsets. As a result, a +22 dBm IIP3 with 3.5 dB NF is achieved. Another challenge in the RX design is the tough NF and linearity requirements for high performance systems such as carrier aggregation. To improve the NF, an extra gain stage is added after the LNA. An N-path high-Q band-pass filter is employed at the LNA output together with baseband blocker filtering technique to attenuate out-of-band blockers and improve the linearity. A noise-cancellation technique based on the frequency translation has been employed to improve the NF. As a result, a 1.8dB NF with +5 dBm IIP3 is achieved. In addition, a new approach has been proposed to reject out of band blockers in carrier aggregation scenarios. The proposed solution also provides carrier to carrier isolation compared to typical solution for carrier aggregation