A 0.1–5.0 GHz flexible SDR receiver with digitally assisted calibration in 65 nm CMOS

© 2017 Elsevier Ltd. All rights reserved.A 0.1–5.0 GHz flexible software-defined radio (SDR) receiver with digitally assisted calibration is presented, employing a zero-IF/low-IF reconfigurable architecture for both wideband and narrowband applications. The receiver composes of a main-path based on a current-mode mixer for low noise, a high linearity sub-path based on a voltage-mode passive mixer for out-of-band rejection, and a harmonic rejection (HR) path with vector gain calibration. A dual feedback LNA with “8” shape nested inductor structure, a cascode inverter-based TCA with miller feedback compensation, and a class-AB full differential Op-Amp with Miller feed-forward compensation and QFG technique are proposed. Digitally assisted calibration methods for HR, IIP2 and image rejection (IR) are presented to maintain high performance over PVT variations. The presented receiver is implemented in 65 nm CMOS with 5.4 mm2 core area, consuming 9.6–47.4 mA current under 1.2 V supply. The receiver main path is measured with +5 dB m/+5dBm IB-IIP3/OB-IIP3 and +61dBm IIP2. The sub-path achieves +10 dB m/+18dBm IB-IIP3/OB-IIP3 and +62dBm IIP2, as well as 10 dB RF filtering rejection at 10 MHz offset. The HR-path reaches +13 dB m/+14dBm IB-IIP3/OB-IIP3 and 62/66 dB 3rd/5th-order harmonic rejection with 30–40 dB improvement by the calibration. The measured sensitivity satisfies the requirements of DVB-H, LTE, 802.11 g, and ZigBee.Peer reviewedFinal Accepted Versio

Guest editorial for the special issue on software-defined radio transceivers and circuits for 5G wireless communications

Yichuang Sun, Baoyong Chi, and Heng Zhang, Guest Editorial for the Special Issue on Software-Defined Radio Transceivers and Circuits for 5G Wireless Communications, published in IEEEE Transactions on Circuits and Systems II: Express Briefs, Vol. 63 (1): 1-3, January 2016, doi: https://doi.org/10.1109/TCSII.2015.2506979.Peer reviewedFinal Accepted Versio

Analysis and Design of Wideband Low Noise Amplifier with Digital Control

The design issues in designing low noise amplifier (LNA) for Software-Defined-Radio (SDR) are reviewed. An inductor-less wideband low noise amplifier aiming at low frequency band (0.2-2GHz) for Software-Defined-Radio is presented. Shunt-shunt LNA with active feedback is used as the first stage which is carefully optimized for low noise and wide band applications. A digitally controlled second stage is employed to provide an additional 12dB gain control. A novel method is proposed to bypass the first stage without degrading input matching. This LNA is fabricated in a standard 0.18 um CMOS technology. The measurement result shows the proposed LNA has a gain range of 6dB-18dB at high gain mode and -12dB-0dB at low gain mode, as well as a –3dB bandwidth of 2GHz. The noise figure (NF) is 3.5-4.5dB in the high gain setting mode. It consumes 20mW from a 1.8V supply

Behavioral modeling for sampling receiver and baseband in Software-Defined Radio

Projecte realitzat en col.laboració amb Illinois Institute of TechnologySoftware Defined-Radio (SDR) consists of a wireless communication in which the transmitter and the receiver are controlled by means of software. Its ultimate goal is to provide a single universal radio transceiver capable of multi-mode multi-standard wireless communications. Modeling of the proper circuits and new designs aimed at SDR is necessary for further development and experimentation. It sharpens our understanding of fundamental processes, helps to make decisions and provides a guide for training exercises. Due to the lack of these models two independent and different models have been created based on new proposed designs. Each modeled design belongs to a different layer of abstraction and therefore, the tool used is different as well. The first proposed model consist of a Simulink (Matlab) file which models the discrete-time signal processing used in a Discrete-time receiver for Bluetooth Radio. The results show good performance when processing a signal that has been transmitted through a noisy channel. The signal at each step is visualized to see the individual effect of each building block. The second proposed model narrows down the topic and focuses on a Widely-tunable, Reconfigurable Analog Baseband filter, for which a Verilog-A model, by using Cadence, has been created. The outstanding feature of the filter is that its programmability is based on the duty-cycle of the input control signals. Moreover, Verilog-A modules bring the design really close to the real circuit, allowing the designer to face problems that the real circuit will present and easing the replacement of the building blocks with new ones when desired. The results for this model show a very little error within the passband of the filter that increases when the attenuation introduced for the stopband becomes higher

An Independently Tunable Tri-band Antenna Design for Concurrent Multi-band Single Chain Radio Receivers

In this paper, a novel tunable tri-band antenna is presented for concurrent, multi-band, single chain radio receivers. The antenna is manufactured on a 50×100 mm FR4 printed circuit board (PCB), and is able to provide three concurrent, independently tunable operating bands covering a frequency range from 600 MHz to 2.7 GHz. The antenna performance is investigated for both numerical and experimental methods when using, first, varactor diodes and, second, digitally tunable capacitors (DTCs) to tune frequencies, which shows the antenna gain can be improved by up to 2.6 dBi by using DTCs. A hardware-in-the-loop test-bed provides a system level evaluation of the proposed antenna in a direct RF digitized, concurrent, tri-band radio receiver. By measuring the receiver’s error vector magnitude, we demonstrate sufficient isolation between concurrent bands achieving 30 MHz of aggregated bandwidth as well as strong resilience to adjacent blockers next to each band. The data reported in this article are available from the ORDA digital repository (https://doi.org/10.15131/shef.data.5346295)

Design of a Direct-Modulation Transmitter with Self-Optimizing Feedback and a Highly Linear, Highly Reconfigurable, Continuously-Tunable Active-RC Baseband Filter for Multiple Standards

This work consists of two main parts: i) Design and implementation of a compact current-reusing 2.4GHz direct-modulation transmitter with on-chip automatic tuning; ii) Design and implementation of a novel highly-reconfigurable, continuously tunable, power-adjustable Active-RC filter for multiple standards. The design, analysis, and experimental verification of a proposed self-calibrating, current reused 2.4GHz, direct-modulation transmitter are introduced. A stacked arrangement of the power amplifier/voltage-controlled oscillator is presented along with a novel LC-tank-tuning algorithm with a simple, low-cost, on-chip implementation. To transmit maximum power, the tuning loop ensures the PA's resonant tank is centered around the operating frequency, and the loop requires no ADC, DSP, or external signal generator. This work also details the proposed tuning-loop algorithm and examines the frequency-dependent nonlinear power-detector. The system was implemented in TSMC 0.18[mu]m CMOS, occupies 0.7 mm² (TX) + 0.1 mm² (self tuning), and was measured in a QFN48 package on FR4 PCB. Automatically adjusting the tank-tuning bits within their tuning range results in >4dB increase in output power. With the self-tuning circuit active, the transmitter delivers a measured output power of > 0dBm to a 100-[omega] differential load, and the system consumes 22.9 mA from a 2.2-V supply. A biquad design methodology and a baseband low-pass filter is presented for wireless and wireline applications with reconfigurable frequency response, selectable order (1st/3rd/5th), continuously tunable cutoff frequency (1MHz-20MHz) and adjustable power consumption (3mW-7.5mW). A discrete capacitor array coarsely tunes the low-pass filter, and a novel Continuous Impedance Multiplier (CIM) then finely tunes the filter. Resistive/capacitive networks select between the Chebyshev and Inverse Chebyshev approximation types. Also, a new stability metric for biquads, Minimum Acceptable Phase Margin (MAPM), is presented and discussed in the context of filter compensation and passband ripple considerations. Experimental results yield an IIP3 of 31.3dBm, a THD of -40dB at 447mV[subscript pk, diff] input signal amplitude, and a DR of 71.4dB. The filters tunable range covers frequencies from 1MHz to 20MHz. In Inverse Chebyshev mode, the filter achieves a passband group delay variation less than ±2:5%. The design is fabricated in 0.13[mu]m CMOS, occupies 1.53mm², and operates from a 1-V supply

Design of Highly linear Gm-C Low Pass and Complex Band Pass Filter for High Frequency Application

The present work deals with the design of low pass filters such as 3rd order Gm-C filter, a duty cycle controlled low pass and a complex band pass filter that can be operated for high frequency applications. The linearity and power consumption of a CMOS Gm-C filter are studied and optimized. Firstly, a doubly terminated 3rd order low-pass Gm-C filter is designed

Behavioral modeling for sampling receiver and baseband in Software-Defined Radio

Projecte realitzat en col.laboració amb Illinois Institute of TechnologySoftware Defined-Radio (SDR) consists of a wireless communication in which the transmitter and the receiver are controlled by means of software. Its ultimate goal is to provide a single universal radio transceiver capable of multi-mode multi-standard wireless communications. Modeling of the proper circuits and new designs aimed at SDR is necessary for further development and experimentation. It sharpens our understanding of fundamental processes, helps to make decisions and provides a guide for training exercises. Due to the lack of these models two independent and different models have been created based on new proposed designs. Each modeled design belongs to a different layer of abstraction and therefore, the tool used is different as well. The first proposed model consist of a Simulink (Matlab) file which models the discrete-time signal processing used in a Discrete-time receiver for Bluetooth Radio. The results show good performance when processing a signal that has been transmitted through a noisy channel. The signal at each step is visualized to see the individual effect of each building block. The second proposed model narrows down the topic and focuses on a Widely-tunable, Reconfigurable Analog Baseband filter, for which a Verilog-A model, by using Cadence, has been created. The outstanding feature of the filter is that its programmability is based on the duty-cycle of the input control signals. Moreover, Verilog-A modules bring the design really close to the real circuit, allowing the designer to face problems that the real circuit will present and easing the replacement of the building blocks with new ones when desired. The results for this model show a very little error within the passband of the filter that increases when the attenuation introduced for the stopband becomes higher

Saw-Less radio receivers in CMOS

Smartphones play an essential role in our daily life. Connected to the internet, we can easily keep in touch with family and friends, even if far away, while ever more apps serve us in numerous ways. To support all of this, higher data rates are needed for ever more wireless users, leading to a very crowded radio frequency spectrum. To achieve high spectrum efficiency while reducing unwanted interference, high-quality band-pass filters are needed. Piezo-electrical Surface Acoustic Wave (SAW) filters are conventionally used for this purpose, but such filters need a dedicated design for each new band, are relatively bulky and also costly compared to integrated circuit chips. Instead, we would like to integrate the filters as part of the entire wireless transceiver with digital smartphone hardware on CMOS chips. The research described in this thesis targets this goal. It has recently been shown that N-path filters based on passive switched-RC circuits can realize high-quality band-select filters on CMOS chips, where the center frequency of the filter is widely tunable by the switching-frequency. As CMOS downscaling following Moore’s law brings us lower clock-switching power, lower switch on-resistance and more compact metal-to-metal capacitors, N-path filters look promising. This thesis targets SAW-less wireless receiver design, exploiting N-path filters. As SAW-filters are extremely linear and selective, it is very challenging to approximate this performance with CMOS N-path filters. The research in this thesis proposes and explores several techniques for extending the linearity and enhancing the selectivity of N-path switched-RC filters and mixers, and explores their application in CMOS receiver chip designs. First the state-of-the-art in N-path filters and mixer-first receivers is reviewed. The requirements on the main receiver path are examined in case SAW-filters are removed or replaced by wideband circulators. The feasibility of a SAW-less Frequency Division Duplex (FDD) radio receiver is explored, targeting extreme linearity and compression Irequirements. A bottom-plate mixing technique with switch sharing is proposed. It improves linearity by keeping both the gate-source and gate-drain voltage swing of the MOSFET-switches rather constant, while halving the switch resistance to reduce voltage swings. A new N-path switch-RC filter stage with floating capacitors and bottom-plate mixer-switches is proposed to achieve very high linearity and a second-order voltage-domain RF-bandpass filter around the LO frequency. Extra out-of-band (OOB) rejection is implemented combined with V-I conversion and zero-IF frequency down-conversion in a second cross-coupled switch-RC N-path stage. It offers a low-ohmic high-linearity current path for out-of-band interferers. A prototype chip fabricated in a 28 nm CMOS technology achieves an in-band IIP3 of +10 dBm , IIP2 of +42 dBm, out-of-band IIP3 of +44 dBm, IIP2 of +90 dBm and blocker 1-dB gain-compression point of +13 dBm for a blocker frequency offset of 80 MHz. At this offset frequency, the measured desensitization is only 0.6 dB for a 0-dBm blocker, and 3.5 dB for a 10-dBm blocker at 0.7 GHz operating frequency (i.e. 6 and 9 dB blocker noise figure). The chip consumes 38-96 mW for operating frequencies of 0.1-2 GHz and occupies an active area of 0.49 mm2. Next, targeting to cover all frequency bands up to 6 GHz and achieving a noise figure lower than 3 dB, a mixer-first receiver with enhanced selectivity and high dynamic range is proposed. Capacitive negative feedback across the baseband amplifier serves as a blocker bypassing path, while an extra capacitive positive feedback path offers further blocker rejection. This combination of feedback paths synthesizes a complex pole pair at the input of the baseband amplifier, which is up-converted to the RF port to obtain steeper RF-bandpass filter roll-off than the conventional up-converted real pole and reduced distortion. This thesis explains the circuit principle and analyzes receiver performance. A prototype chip fabricated in 45 nm Partially Depleted Silicon on Insulator (PDSOI) technology achieves high linearity (in-band IIP3 of +3 dBm, IIP2 of +56 dBm, out-of-band IIP3 = +39 dBm, IIP2 = +88 dB) combined with sub-3 dB noise figure. Desensitization due to a 0-dBm blocker is only 2.2 dB at 1.4 GHz operating frequency. IIFinally, to demonstrate the performance of the implemented blocker-tolerant receiver chip designs, a test setup with a real mobile phone is built to verify the sensitivity of the receiver chip for different practical blocking scenarios