Analysis on Supercapacitor Assisted Low Dropout (SCALDO) Regulators

State-of-the-art electronic systems employ three fundamental techniques for DC-DC converters: (a) switch-mode power supplies (SMPS); (b) linear power supplies; (c) switched capacitor (charge pump) converters. In practical systems, these three techniques are mixed to provide a complex, but elegant, overall solution, with energy efficiency, effective PCB footprint, noise and transient performance to suit different electronic circuit blocks. Switching regulators have relatively high end-to-end efficiency, in the range of 70 to 93%, but can have issues with output noise and EMI/RFI emissions. Switched capacitor converters use a set of capacitors for energy storage and conversion. In general, linear regulators have low efficiencies in the range 30 to 60%. However, they have outstanding output characteristics such as low noise, excellent transient response to load current fluctuations, design simplicity and low cost design which are far superior to SMPS. Given the complex situation in switch-mode converters, low dropout (LDO) regulators were introduced to address the equirements of noise-sensitive and fast transient loads in portable devices. A typical commercial off-the-shelf LDO has its input voltage slightly higher than the desired regulated output for optimal efficiency. The approximate efficiency of a linear regulator, if the power consumed by the control circuits is negligible, can be expressed by the ratio of Vo/Vin. A very low frequency supercapacitor circulation technique can be combined with commercial low dropout regulator ICs to significantly increase the end-to-end efficiency by a multiplication factor in the range of 1.33 to 3, compared to the efficiency of a linear regulator circuit with the same input-output voltages. In this patented supercapacitor-assisted low dropout (SCALDO) regulator technique developed by a research team at the University of Waikato, supercapacitors are used as lossless voltage droppers, and the energy reuse occurs at very low frequencies in the range of less than ten hertz, eliminating RFI/EMI concerns. This SCALDO technique opens up a new approach to design step-down, DC-DC converters suitable for processor power supplies with very high end-to-end efficiency which is closer to the efficiencies of practical switching regulators, while maintaining the superior output specifications of a linear design. Furthermore, it is important to emphasize that the SCALDO technique is not a variation of well-known switched capacitor DC-DC converters. In this thesis, the basic SCALDO concept is further developed to achieve generalised topologies, with the relevant theory that can be applied to a converter with any input-output step-down voltage combination. For these generalised topologies, some important design parameters, such as the number of supercapacitors, switching matrix details and efficiency improvement factors, are derived to form the basis of designing SCALDO regulators. With the availability of commercial LDO ICs with output current ratings up to 10 A, and thin-prole supercapacitors with DC voltage ratings from 2.3 to 5.5 V, several practically useful, medium-current SCALDO prototypes: 12V-to-5V, 5V-to-2V, 5.5V-to-3.3V have been developed. Experimental studies were carried out on these SCALDO prototypes to quantify performance in terms of line regulation, load regulation, efficiency and transient response. In order to accurately predict the performance and associated waveforms of the individual phases (charge, discharge and transition) of the SCALDO regulator, Laplace transform-based theory for supercapacitor circulation is developed, and analytical predictions are compared with experimental measurements for a 12V-to-5V prototype. The analytical results tallied well with the practical waveforms observed in a 12V-to-5V converter, indicating that the SCALDO technique can be generalized to other versatile configurations, and confirming that the simplified assumptions used to describe the circuit elements are reasonable and justifiable. After analysing the performance of several SCALDO prototypes, some practical issues in designing SCALDO regulators have been identified. These relate to power losses and implications for future development of the SCALDO design

Power conversion techniques in nanometer CMOS for low-power applications

As System-on-Chip (SoCs) in nanometer CMOS technologies grow larger, the power management process within these SoCs becomes very challenging. In the heart of this process lies the challenge of implementing energy-efficient and cost-effective DC-DC power converters. To address this challenge, this thesis studies in details three different aspects of DC-DC power converters and proposes potential solutions. First, to maximize power conversion efficiency, loss mechanisms must be studied and quantified. For that purpose, we provide comprehensive analysis and modeling of the various switching and conduction losses in low-power synchronous DC-DC buck converters in both Continuous Conduction Mode (CCM) and Discontinuous Conduction Mode (DCM) operation, including the case with non-rail gate control of the power switches. Second, a DC-DC buck converter design with only on-chip passives is proposed and implemented in 65-nm CMOS technology. The converter switches at 588 MHz and uses a 20-nH and 300-pF on-chip inductor and capacitor respectively, and provides up to 30-mA of load at an output voltage in the range of 0.8-1.2 V. The proposed design features over 10% improvement in power conversion efficiency over a corresponding linear regulator while preserving low-cost implementation. Finally, a 40-mA buck converter design operating in the inherently-stable DCM mode for the entire load range is presented. It employs a Pulse Frequency Modulation (PFM) scheme using a Hysteretic-Assisted Adaptive Minimum On-Time (HA-AMOT) controller to automatically adapt to a wide range of operating scenarios while minimizing inductor peak current. As a result, compact silicon area, low quiescent current, high efficiency, and robust performance across all conditions can be achieved without any calibration

On-chip Voltage Regulator– Circuit Design and Automation

Title from PDF of title page viewed May 24, 2021Dissertation advisors: Masud H Chowdhury and Yugyung LeeVitaIncludes bibliographical references (page 106-121)Thesis (Ph.D.)--School of Computing and Engineering. University of Missouri--Kansas City, 2021With the increase of density and complexity of high-performance integrated circuits and systems, including many-core chips and system-on-chip (SoC), it is becoming difficult to meet the power delivery and regulation requirements with off-chip regulators. The off-chip regulators become a less attractive choice because of the higher overheads and complexity imposed by the additional wires, pins, and pads. The increased I2R loss makes it challenging to maintain the integrity of different voltage domains under a lower supply voltage environment in the smaller technology nodes. Fully integrated on-chip voltage regulators have proven to be an effective solution to mitigate power delivery and integrity issues. Two types of regulators are considered as most promising for on-chip implementation: (i) the low-drop-out (LDO) regulator and (ii) the switched-capacitor (SC)regulator. The first part of our research mainly focused on the LDO regulator. Inspired by the recent surge of interest for cap-less voltage regulators, we presented two fully on-chip external capacitor-less low-dropout voltage regulator design. The second part of this proposal explores the complexity of designing each block of the regulator/analog circuit and proposed a design methodology for analog circuit synthesis using simulation and learning-based approach. As the complexity is increasing day-by-day in an analog circuit, hierarchical flow mostly uses for design automation. In this work, we focused mainly on Circuit-level, one of the significant steps in the flow. We presented a novel, efficient circuit synthesis flow based on simulation and learning-based optimization methods. The proposed methodology has two phases: the learning phase and the evaluation phase. Random forest, a supervised learning is used to reduce the sample points in the design space and iteration number during the learning phase. Additionally, symmetric constraints are used further to reduce the iteration number during the sizing process. We introduced a three-step circuit synthesis flow to automate the analog circuit design. We used H-spice as a simulation tool during the evaluation phase of the proposed methodology. The three most common analog circuits are chosen: single-stage differential amplifier, operational transconductance amplifier, and two-stage differential amplifier to verify the algorithm. The tool is developed in Python, and the technology we used is0.6um. We also verified the optimized result in Cadence Virtuoso.Introduction -- On-chip power delivery system -- Fundamentals of on-chip voltage regulator -- LDO design in 45NM technology -- LDO design in technology -- Analog design automation -- Proposed analog design methodology -- Energy efficient FDSOI and FINFET based power gating circuit using data retention transistor -- Conclusion and future wor

A 0.21-ps FOM Capacitor-Less Analog LDO with Dual-Range Load Current for Biomedical Applications

This paper presents an output capacitor-less low-dropout regulator (LDO) with a bias switching scheme for biomedical applications with dual-range load currents. Power optimization is crucial for systems with multiple activation modes such as neural interfaces, IoT and edge devices with varying load currents. To enable rapid switching between low and high current states, a flipped voltage follower (FVF) configuration is utilized, along with a super source follower buffer to drive the power transistor. Two feedback loops and an on-chip compensation capacitor Cc maintain the stability of the regulator under various load conditions. The LDO was implemented in a 65nm CMOS process with 1.5V input and 1.2V output voltages. The measured quiescent current is as low as 3uA and 50uA for the 0-500uA and 5-15mA load current ranges, respectively. An undershoot voltage of 100mV is observed when the load current switches from 0 to 15mA within 80ns, with a maximum current efficiency of 99.98%. Our design achieved a low Figure-of-Merit of 0.21ps, outperforming state-of-the-art analog LDOs

0.6-V-VIN 7.0-nA-IQ 0.75-mA-IL CMOS Capacitor-Less LDO for Low-Voltage Micro-Energy-Harvested Supplies

A capacitor-less (CL) low-dropout (LDO) regulator suitable to be incorporated in an on-chip system with low-voltage micro-energy-harvested supply, is proposed in this contribution. The differential input stage of the error amplifier includes bulk-driven MOS transistors, thus providing the LDO with an output voltage range that extends from the negative rail up to a level very close to the input voltage without the need of using a resistive feedback network. The circuit parameters relying on the feedback factor, , are maximized thanks to the use of a unitary value for this parameter. The CL-LDO has been designed and fabricated in standard 180-nm CMOS technology and optimized to operate with an input voltage equal to 0.6 V and a reference level of 0.5 V. The experimental characterization of the fabricated prototypes shows that, under these operating conditions, the LDO is able to deliver a load current above 0.75 mA with a total quiescent current of only 7.0 nA. Furthermore, the proposed voltage regulator is able to operate from input voltages as low as 0.4 V, delivering in this case a maximum load current of 30 μA.RTI2018- 095994-B-I00 ED431G-2019/04 GRC2021/48 IB18079S

Design of Analog & Mixed Signal Circuits in Continuous-Time Sigma-Delta Modulators for System-on-Chip applications

Software-defined radio receivers (SDRs) have become popular to accommodate multi-standard wireless services using a single chip-set solution in mobile telecommunication systems. In SDRs, the signal is down-converted to an intermediate frequency and then digitalized. This approach relaxes the specifications for most of the analog front-end building blocks by performing most of the signal processing in the digital domain. However, since the analog-to-digital converter (ADC) is located as close as possible to the antenna in SDR architectures, the ADC specification requirements are very stringent because a large amount of interference signals are present at the ADC input due to the removal of filtering blocks, which particularly affects the dynamic range (DR) specification. Sigma-delta (ΣΔ) ADCs have several benefits such as low implementation cost, especially when the architecture contains mostly digital circuits. Furthermore, continuous-time (CT) ΣΔ ADCs allow elimination of the anti‐aliasing filter because input signals are sampled after the integrator. The bandwidth requirements for the amplifiers in CT ΣΔ ADCs can be relaxed due to the continuous operation without stringing settling time requirements. Therefore, they are suitable for high‐speed and low‐power applications. In addition, CT ΣΔ ADCs achieve high resolution due to the ΣΔ modulator’s noise shaping property. However, the in-band quantization noise is shaped by the analog loop filter and the distortions of the analog loop filter directly affect the system output. Hence, highly linear low-noise loop filters are required for high-performance ΣΔ modulators. The first task in this research focused on using CMOS 90 nm technology to design and fabricate a 5^(TH)–order active-RC loop filter with a cutoff frequency of 20 MHz for a low pass (LP) CT ΣΔ modulator. The active-RC topology was selected because of the high DR requirement in SDR applications. The amplifiers in the first stage of the loop filter were implemented with linearization techniques employing anti-parallel cancellation and source degeneration in the second stage of the amplifiers. These techniques improve the third-order intermodulation (IM3) by approximately 10 dB; while noise, area, and power consumption do not increase by more than 10%. Second, a current-mode adder-flash ADC was also fabricated as part of a LP CT ΣΔ modulator. The new current-mode operation developed through this research makes possible a 53% power reduction. The new technology also lessens existing problems associated with voltage-mode flash ADCs, which are mainly related to voltage headroom restrictions, speed of operation, offsets, and power efficiency of the latches. The core of the current-mode adder-flash ADC was fabricated in CMOS 90 nm technology with 1.2 V supply; it dissipates 3.34 mW while operating at 1.48 GHz and consumes a die area of 0.0276 mm^(2). System-on chip (SoC) solutions are becoming more popular in mobile telecommunication systems to improve the portability and competitiveness of products. Since the analog/RF and digital blocks often share the same external power supply in SoC solutions, the on-chip generation of clean power supplies is necessary to avoid system performance degradation due to supply noises. Finally, the critical design issues for external capacitor-less low drop-out (LDO) regulators for SoC applications are addressed in this dissertation, especially the challenges related to power supply rejection at high frequencies as well as loop stability and transient response. The paths of the power supply noise to the LDO output were analyzed, and a power supply noise cancellation circuit was developed. The power supply rejection (PSR) performance was improved by using a replica circuit that tracks the main supply noise under process-voltage-temperature variations and all operating conditions. Fabricated in a 0.18 μm CMOS technology with 1.8 V supply, the entire proposed LDO consumes 55 μA of quiescent current while in standby operation, and it has a drop-out voltage of 200 mV when providing 50 mA to the load. Its active core chip area is 0.14 mm2. Compared to a conventional uncompensated LDO, the proposed architecture presents a PSR improvement of 34 dB and 25 dB at 1 MHz and 4 MHz, respectively

A Flexible, Highly Integrated, Low Power pH Readout

Medical devices are widely employed in everyday life as wearable and implantable technologies make more and more technological breakthroughs. Implantable biosensors can be implanted into the human body for monitoring of relevant physiological parameters, such as pH value, glucose, lactate, CO2 [carbon dioxide], etc. For these applications the implantable unit needs a whole functional set of blocks such as micro- or nano-sensors, sensor signal processing and data generation units, wireless data transmitters etc., which require a well-designed implantable unit.Microelectronics technology with biosensors has caused more and more interest from both academic and industrial areas. With the advancement of microelectronics and microfabrication, it makes possible to fabricate a complete solution on an integrated chip with miniaturized size and low power consumption.This work presents a monolithic pH measurement system with power conditioning system for supply power derived from harvested energy. The proposed system includes a low-power, high linearity pH readout circuits with wide pH values (0-14) and a power conditioning unit based on low drop-out (LDO) voltage regulator. The readout circuit provides square-wave output with frequency being highly linear corresponding to the input pH values. To overcome the process variations, a simple calibration method is employed in the design which makes the output frequency stay constant over process, supply voltage and temperature variations. The prototype circuit is designed and fabricated in a standard 0.13-μm [micro-meter] CMOS process and shows good linearity to cover the entire pH value range from 0-14 while the voltage regulator provides a stable supply voltage for the system

A Case Study in CMOS Design Scaling for Analog Applications: The Ringamp LDO

As CMOS process nodes scale to smaller feature sizes, process optimizations are made to achieve improvements in digital circuit performance, such as increasing speed and memory, while decreasing power consumption. Unfortunately for analog design, these optimizations usually come at the expense of poorer transistor performance, such as reduced small signal output resistance and increased channel length modulation. The ring amplifier has been proposed as a digital solution to the analog scaling problem, by configuring digital inverters to function as analog amplifiers through deadzone biasing. As digital inverters naturally scale, the ring amplifier is a promising area of exploration for analog design. This work presents a ring amplifier scaling study by demonstration of scaling an output capacitor-less, ring amplifier based low-dropout voltage regulator designed in a standard 180 nm CMOS process down to a standard 90 nm CMOS process

Ultra-Low Power Transmitter and Power Management for Internet-of-Things Devices

Two of the most critical components in an Internet-of-Things (IoT) sensing and transmitting node are the power management unit (PMU) and the wireless transmitter (Tx). The desire for longer intervals between battery replacements or a completely self-contained, battery-less operation via energy harvesting transducers and circuits in IoT nodes demands highly efficient integrated circuits. This dissertation addresses the challenge of designing and implementing power management and Tx circuits with ultra-low power consumption to enable such efficient operation. The first part of the dissertation focuses on the study and design of power management circuits for IoT nodes. This opening portion elaborates on two different areas of the power management field: Firstly, a low-complexity, SPICE-based model for general low dropout (LDO) regulators is demonstrated. The model aims to reduce the stress and computation times in the final stages of simulation and verification of Systems-on-Chip (SoC), including IoT nodes, that employ large numbers of LDOs. Secondly, the implementation of an efficient PMU for an energy harvesting system based on a thermoelectric generator transducer is discussed. The PMU includes a first-in-its-class LDO with programmable supply noise rejection for localized improvement in the suppression. The second part of the dissertation addresses the challenge of designing an ultra- low power wireless FSK Tx in the 900 MHz ISM band. To reduce the power consumption and boost the Tx energy efficiency, a novel delay cell exploiting current reuse is used in a ring-oscillator employed as the local oscillator generator scheme. In combination with an edge-combiner PA, the Tx showed a measured energy efficiency of 0.2 nJ/bit and a normalized energy efficiency of 3.1 nJ/(bit∙mW) when operating at output power levels up to -10 dBm and data rates of 3 Mbps. To close this dissertation, the implementation of a supply-noise tolerant BiCMOS ring-oscillator is discussed. The combination of a passive, high-pass feedforward path from the supply to critical nodes in the selected delay cell and a low cost LDO allow the oscillator to exhibit power supply noise rejection levels better than –33 dB in experimental results

Integrated circuit & system design for concurrent amperometric and potentiometric wireless electrochemical sensing

Complementary Metal-Oxide-Semiconductor (CMOS) biosensor platforms have steadily grown in healthcare and commerial applications. This technology has shown potential in the field of commercial wearable technology, where CMOS sensors aid the development of miniaturised sensors for an improved cost of production and response time. The possibility of utilising wireless power and data transmission techniques for CMOS also allows for the monolithic integration of the communication, power and sensing onto a single chip, which greatly simplifies the post-processing and improves the efficiency of data collection. The ability to concurrently utilise potentiometry and amperometry as an electrochemical technique is explored in this thesis. Potentiometry and amperometry are two of the most common transduction mechanisms for electrochemistry, with their own advantages and disadvantages. Concurrently applying both techniques will allow for real-time calibration of background pH and for improved accuracy of readings. To date, developing circuits for concurrently sensing potentiometry and amperometry has not been explored in the literature. This thesis investigates the possibility of utilising CMOS sensors for wireless potentiometric and amperometric electrochemical sensing. To start with, a review of potentiometry and amperometry is evaluated to understand the key factors behind their operation. A new configuration is proposed whereby the reference electrode for both electrochemistry techniques are shared. This configuration is then compared to both the original configurations to determine any differences in the sensing accuracy through a novel experiment that utilises hydrogen peroxide as a measurement analyte. The feasibility of the configuration with the shared reference electrode is proven and utilised as the basis of the electrochemical configuration for the front end circuits. A unique front-end circuit named DAPPER is developed for the shared reference electrode topology. A review of existing architectures for potentiometry and amperometry is evaluated, with a specific focus on low power consumption for wireless applications. In addition, both the electrochemical sensing outputs are mixed into a single output data channel for use with a near-field communication (NFC). This mixing technique is also further analysed in this thesis to understand the errors arising due to various factors. The system is fabricated on TSMC 180nm technology and consumes 28µW. It measures a linear input current range from 250pA - 0.1µW, and an input voltage range of 0.4V - 1V. This circuit is tested and verified for both electrical and electrochemical tests to showcase its feasibility for concurrent measurements. This thesis then provides the integration of wireless blocks into the system for wireless powering and data transmission. This is done through the design of a circuit named SPACEMAN that consists of the concurrent sensing front-end, wireless power blocks, data transmission, as well as a state machine that allows for the circuit to switch between modes: potentiometry only, amperometry only, concurrent sensing and none. The states are switched through re-booting the circuit. The core size of the electronics is 0.41mm² without the coil. The circuit’s wireless powering and data transmission is tested and verified through the use of an external transmitter and a connected printed circuit board (PCB) coil. Finally, the future direction for ongoing work to proceed towards a fully monolithic electrochemical technique is discussed through the next development of a fully integrated coil-on-CMOS system, on-chip electrodes with the electroplating and microfludics, the development of an external transmitter for powering the device and a test platform. The contributions of this thesis aim to formulate a use for wireless electrochemical sensors capable of concurrent measurements for use in wearable devices.Open Acces