High efficiency smart voltage regulating module for green mobile computing

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.In this thesis a design for a smart high efficiency voltage regulating module capable of supplying the core of modern microprocessors incorporating dynamic voltage and frequency scaling (DVS) capability is accomplished using a RISC based microcontroller to facilitate all the functions required to control, protect, and supply the core with the required variable operating voltage as set by the DVS management system. Normally voltage regulating modules provide maximum power efficiency at designed peak load, and the efficiency falls off as the load moves towards lesser values. A mathematical model has been derived for the main converter and small signal analysis has been performed in order to determine system operation stability and select a control scheme that would improve converter operation response to transients and not requiring intense computational power to realize. A Simulation model was built using Matlab/Simulink and after experimenting with tuned PID controller and fuzzy logic controllers, a simple fuzzy logic control scheme was selected to control the pulse width modulated converter and several methods were devised to reduce the requirements for computational power making the whole system operation realizable using a low power RISC based microcontroller. The same microcontroller provides circuit adaptations operation in addition to providing protection to load in terms of over voltage and over current protection. A novel circuit technique and operation control scheme enables the designed module to selectively change some of the circuit elements in the main pulse width modulated buck converter so as to improve efficiency over a wider range of loads. In case of very light loads as the case when the device goes into standby, sleep or hibernation mode, a secondary converter starts operating and the main converter stops. The secondary converter adapts a different operation scheme using switched capacitor technique which provides high efficiency at low load currents. A fuzzy logic control scheme was chosen for the main converter for its lighter computational power requirement promoting implementation using ultra low power embedded controllers. Passive and active components were carefully selected to augment operational efficiency. These aspects enabled the designed voltage regulating module to operate with efficiency improvement in off peak load region in the range of 3% to 5%. At low loads as the case when the computer system goes to standby or sleep mode, the efficiency improvent is better than 13% which will have noticeable contribution in extending battery run time thus contributing to lowering the carbon footprint of human consumption

Thermal-Aware Networked Many-Core Systems

Advancements in IC processing technology has led to the innovation and growth happening in the consumer electronics sector and the evolution of the IT infrastructure supporting this exponential growth. One of the most difficult obstacles to this growth is the removal of large amount of heatgenerated by the processing and communicating nodes on the system. The scaling down of technology and the increase in power density is posing a direct and consequential effect on the rise in temperature. This has resulted in the increase in cooling budgets, and affects both the life-time reliability and performance of the system. Hence, reducing on-chip temperatures has become a major design concern for modern microprocessors. This dissertation addresses the thermal challenges at different levels for both 2D planer and 3D stacked systems. It proposes a self-timed thermal monitoring strategy based on the liberal use of on-chip thermal sensors. This makes use of noise variation tolerant and leakage current based thermal sensing for monitoring purposes. In order to study thermal management issues from early design stages, accurate thermal modeling and analysis at design time is essential. In this regard, spatial temperature profile of the global Cu nanowire for on-chip interconnects has been analyzed. It presents a 3D thermal model of a multicore system in order to investigate the effects of hotspots and the placement of silicon die layers, on the thermal performance of a modern ip-chip package. For a 3D stacked system, the primary design goal is to maximise the performance within the given power and thermal envelopes. Hence, a thermally efficient routing strategy for 3D NoC-Bus hybrid architectures has been proposed to mitigate on-chip temperatures by herding most of the switching activity to the die which is closer to heat sink. Finally, an exploration of various thermal-aware placement approaches for both the 2D and 3D stacked systems has been presented. Various thermal models have been developed and thermal control metrics have been extracted. An efficient thermal-aware application mapping algorithm for a 2D NoC has been presented. It has been shown that the proposed mapping algorithm reduces the effective area reeling under high temperatures when compared to the state of the art.Siirretty Doriast

On Energy Efficient Computing Platforms

In accordance with the Moore's law, the increasing number of on-chip integrated transistors has enabled modern computing platforms with not only higher processing power but also more affordable prices. As a result, these platforms, including portable devices, work stations and data centres, are becoming an inevitable part of the human society. However, with the demand for portability and raising cost of power, energy efficiency has emerged to be a major concern for modern computing platforms. As the complexity of on-chip systems increases, Network-on-Chip (NoC) has been proved as an efficient communication architecture which can further improve system performances and scalability while reducing the design cost. Therefore, in this thesis, we study and propose energy optimization approaches based on NoC architecture, with special focuses on the following aspects. As the architectural trend of future computing platforms, 3D systems have many bene ts including higher integration density, smaller footprint, heterogeneous integration, etc. Moreover, 3D technology can signi cantly improve the network communication and effectively avoid long wirings, and therefore, provide higher system performance and energy efficiency. With the dynamic nature of on-chip communication in large scale NoC based systems, run-time system optimization is of crucial importance in order to achieve higher system reliability and essentially energy efficiency. In this thesis, we propose an agent based system design approach where agents are on-chip components which monitor and control system parameters such as supply voltage, operating frequency, etc. With this approach, we have analysed the implementation alternatives for dynamic voltage and frequency scaling and power gating techniques at different granularity, which reduce both dynamic and leakage energy consumption. Topologies, being one of the key factors for NoCs, are also explored for energy saving purpose. A Honeycomb NoC architecture is proposed in this thesis with turn-model based deadlock-free routing algorithms. Our analysis and simulation based evaluation show that Honeycomb NoCs outperform their Mesh based counterparts in terms of network cost, system performance as well as energy efficiency.Siirretty Doriast

To develop an efficient variable speed compressor motor system

This research presents a proposed new method of improving the energy efficiency of a Variable Speed Drive (VSD) for induction motors. The principles of VSD are reviewed with emphasis on the efficiency and power losses associated with the operation of the variable speed compressor motor drive, particularly at low speed operation.The efficiency of induction motor when operated at rated speed and load torque is high. However at low load operation, application of the induction motor at rated flux will cause the iron losses to increase excessively, hence its efficiency will reduce dramatically. To improve this efficiency, it is essential to obtain the flux level that minimizes the total motor losses. This technique is known as an efficiency or energy optimization control method. In practice, typical of the compressor load does not require high dynamic response, therefore improvement of the efficiency optimization control that is proposed in this research is based on scalar control model.In this research, development of a new neural network controller for efficiency optimization control is proposed. The controller is designed to generate both voltage and frequency reference signals imultaneously. To achieve a robust controller from variation of motor parameters, a real-time or on-line learning algorithm based on a second order optimization Levenberg-Marquardt is employed. The simulation of the proposed controller for variable speed compressor is presented. The results obtained clearly show that the efficiency at low speed is significant increased. Besides that the speed of the motor can be maintained. Furthermore, the controller is also robust to the motor parameters variation. The simulation results are also verified by experiment

Improving processor efficiency through thermal modeling and runtime management of hybrid cooling strategies

One of the main challenges in building future high performance systems is the ability to maintain safe on-chip temperatures in presence of high power densities. Handling such high power densities necessitates novel cooling solutions that are significantly more efficient than their existing counterparts. A number of advanced cooling methods have been proposed to address the temperature problem in processors. However, tradeoffs exist between performance, cost, and efficiency of those cooling methods, and these tradeoffs depend on the target system properties. Hence, a single cooling solution satisfying optimum conditions for any arbitrary system does not exist. This thesis claims that in order to reach exascale computing, a dramatic improvement in energy efficiency is needed, and achieving this improvement requires a temperature-centric co-design of the cooling and computing subsystems. Such co-design requires detailed system-level thermal modeling, design-time optimization, and runtime management techniques that are aware of the underlying processor architecture and application requirements. To this end, this thesis first proposes compact thermal modeling methods to characterize the complex thermal behavior of cutting-edge cooling solutions, mainly Phase Change Material (PCM)-based cooling, liquid cooling, and thermoelectric cooling (TEC), as well as hybrid designs involving a combination of these. The proposed models are modular and they enable fast and accurate exploration of a large design space. Comparisons against multi-physics simulations and measurements on testbeds validate the accuracy of our models (resulting in less than 1C error on average) and demonstrate significant reductions in simulation time (up to four orders of magnitude shorter simulation times). This thesis then introduces temperature-aware optimization techniques to maximize energy efficiency of a given system as a whole (including computing and cooling energy). The proposed optimization techniques approach the temperature problem from various angles, tackling major sources of inefficiency. One important angle is to understand the application power and performance characteristics and to design management techniques to match them. For workloads that require short bursts of intense parallel computation, we propose using PCM-based cooling in cooperation with a novel Adaptive Sprinting technique. By tracking the PCM state and incorporating this information during runtime decisions, Adaptive Sprinting utilizes the PCM heat storage capability more efficiently, achieving 29\% performance improvement compared to existing sprinting policies. In addition to the application characteristics, high heterogeneity in on-chip heat distribution is an important factor affecting efficiency. Hot spots occur on different locations of the chip with varying intensities; thus, designing a uniform cooling solution to handle worst-case hot spots significantly reduces the cooling efficiency. The hybrid cooling techniques proposed as part of this thesis address this issue by combining the strengths of different cooling methods and localizing the cooling effort over hot spots. Specifically, the thesis introduces LoCool, a cooling system optimizer that minimizes cooling power under temperature constraints for hybrid-cooled systems using TECs and liquid cooling. Finally, the scope of this work is not limited to existing advanced cooling solutions, but it also extends to emerging technologies and their potential benefits and tradeoffs. One such technology is integrated flow cell array, where fuel cells are pumped through microchannels, providing both cooling and on-chip power generation. This thesis explores a broad range of design parameters including maximum chip temperature, leakage power, and generated power for flow cell arrays in order to maximize the benefits of integrating this technology with computing systems. Through thermal modeling and runtime management techniques, and by exploring the design space of emerging cooling solutions, this thesis provides significant improvements in processor energy efficiency.2018-07-09T00:00:00

A Survey of Phase Classification Techniques for Characterizing Variable Application Behavior

Adaptable computing is an increasingly important paradigm that specializes system resources to variable application requirements, environmental conditions, or user requirements. Adapting computing resources to variable application requirements (or application phases) is otherwise known as phase-based optimization. Phase-based optimization takes advantage of application phases, or execution intervals of an application, that behave similarly, to enable effective and beneficial adaptability. In order for phase-based optimization to be effective, the phases must first be classified to determine when application phases begin and end, and ensure that system resources are accurately specialized. In this paper, we present a survey of phase classification techniques that have been proposed to exploit the advantages of adaptable computing through phase-based optimization. We focus on recent techniques and classify these techniques with respect to several factors in order to highlight their similarities and differences. We divide the techniques by their major defining characteristics---online/offline and serial/parallel. In addition, we discuss other characteristics such as prediction and detection techniques, the characteristics used for prediction, interval type, etc. We also identify gaps in the state-of-the-art and discuss future research directions to enable and fully exploit the benefits of adaptable computing.Comment: To appear in IEEE Transactions on Parallel and Distributed Systems (TPDS

A Review of Physical Human Activity Recognition Chain Using Sensors

In the era of Internet of Medical Things (IoMT), healthcare monitoring has gained a vital role nowadays. Moreover, improving lifestyle, encouraging healthy behaviours, and decreasing the chronic diseases are urgently required. However, tracking and monitoring critical cases/conditions of elderly and patients is a great challenge. Healthcare services for those people are crucial in order to achieve high safety consideration. Physical human activity recognition using wearable devices is used to monitor and recognize human activities for elderly and patient. The main aim of this review study is to highlight the human activity recognition chain, which includes, sensing technologies, preprocessing and segmentation, feature extractions methods, and classification techniques. Challenges and future trends are also highlighted.