Design of On-Chip Self-Testing Signature Register

Over the last few years, scan test has turn out to be too expensive to implement for industry standard designs due to increasing test data volume and test time. The test cost of a chip is mainly governed by the resource utilization of Automatic Test Equipment (ATE). Also, it directly depends upon test time that includes time required to load test program, to apply test vectors and to analyze generated test response of the chip. An issue of test time and data volume is increasingly appealing designers to use on-chip test data compactors, either on input side or output side or both. Such techniques significantly address the former issues but have little hold over increasing number of input-outputs under test mode. Further, test pins on DUT are increasing over the generations. Thus, scan channels on test floor are falling short in number for placement of such ICs. To address issues discussed above, we introduce an on-chip self-testing signature register. It comprises a response compactor and a comparator. The compactor compacts large chunk of response data to a small test signature whereas the comparator compares this test signature with desired one. The overall test result for the design is generated on single output pin. Being no storage of test response is demanded, the considerable reduction in ATE memory can be observed. Also, with only single pin to be monitored for test result, the number of tester channels and compare edges on ATE side significantly reduce at the end of the test. This cuts down maintenance and usage cost of test floor and increases its life time. Furthermore reduction in test pins gives scope for DFT engineers to increase number of scan chains so as to further reduce test time

Ensuring a High Quality Digital Device through Design for Testability

An electronic device is reliable if it is available for use most of the times throughout its life. The reliability can be affected by mishandling and use under abnormal operating conditions. High quality product cannot be achieved without proper verification and testing during the product development cycle. If the design is difficult to test, then it is very likely that most of the faults will not be detected before it is shipped to the customer. This paper describes how product quality can be improved by making the hardware design testable. Various designs for testability techniqueswere discussed. A three bit counter circuit was used to illustrate the benefits of design for testability by using scan chain methodology

A Structured Design Methodology for High Performance VLSI Arrays

abstract: The geometric growth in the integrated circuit technology due to transistor scaling also with system-on-chip design strategy, the complexity of the integrated circuit has increased manifold. Short time to market with high reliability and performance is one of the most competitive challenges. Both custom and ASIC design methodologies have evolved over the time to cope with this but the high manual labor in custom and statistic design in ASIC are still causes of concern. This work proposes a new circuit design strategy that focuses mostly on arrayed structures like TLB, RF, Cache, IPCAM etc. that reduces the manual effort to a great extent and also makes the design regular, repetitive still achieving high performance. The method proposes making the complete design custom schematic but using the standard cells. This requires adding some custom cells to the already exhaustive library to optimize the design for performance. Once schematic is finalized, the designer places these standard cells in a spreadsheet, placing closely the cells in the critical paths. A Perl script then generates Cadence Encounter compatible placement file. The design is then routed in Encounter. Since designer is the best judge of the circuit architecture, placement by the designer will allow achieve most optimal design. Several designs like IPCAM, issue logic, TLB, RF and Cache designs were carried out and the performance were compared against the fully custom and ASIC flow. The TLB, RF and Cache were the part of the HEMES microprocessor.Dissertation/ThesisPh.D. Electrical Engineering 201

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi

Algorithmic techniques for physical design : macro placement and under-the-cell routing

With the increase of chip component density and new manufacturability constraints imposed by modern technology nodes, the role of algorithms for electronic design automation is key to the successful implementation of integrated circuits. Two of the critical steps in the physical design flows are macro placement and ensuring all design rules are honored after timing closure. This thesis proposes contributions to help in these stages, easing time-consuming manual steps and helping physical design engineers to obtain better layouts in reduced turnaround time. The first contribution is under-the-cell routing, a proposal to systematically connect standard cell components via lateral pins in the lower metal layers. The aim is to reduce congestion in the upper metal layers caused by extra metal and vias, decreasing the number of design rule violations. To allow cells to connect by abutment, a standard cell library is enriched with instances containing lateral pins in a pre-selected sharing track. Algorithms are proposed to maximize the numbers of connections via lateral connection by mapping placed cell instances to layouts with lateral pins, and proposing local placement modifications to increase the opportunities for such connections. Experimental results show a significant decrease in the number of pins, vias, and in number of design rule violations, with negligible impact on wirelength and timing. The second contribution, done in collaboration with eSilicon (a leading ASIC design company), is the creation of HiDaP, a macro placement tool for modern industrial designs. The proposed approach follows a multilevel scheme to floorplan hierarchical blocks, composed of macros and standard cells. By exploiting RTL information available in the netlist, the dataflow affinity between these blocks is modeled and minimized to find a macro placement with good wirelength and timing properties. The approach is further extended to allow additional engineer input, such as preferred macro locations, and also spectral and force methods to guide the floorplanning search. Experimental results show that the layouts generated by HiDaP outperforms those obtained by a state-of-the-art EDA physical design software, with similar wirelength and better timing when compared to manually designed tape-out ready macro placements. Layouts obtained by HiDaP have successfully been brought to near timing closure with one to two rounds of small modifications by physical design engineers. HiDaP has been fully integrated in the design flows of the company and its development remains an ongoing effort.A causa de l'increment de la densitat de components en els xip i les noves restriccions de disseny imposades pels últims nodes de fabricació, el rol de l'algorísmia en l'automatització del disseny electrònic ha esdevingut clau per poder implementar circuits integrats. Dos dels passos crucials en el procés de disseny físic és el placement de macros i assegurar la correcció de les regles de disseny un cop les restriccions de timing del circuit són satisfetes. Aquesta tesi proposa contribucions per ajudar en aquests dos reptes, facilitant laboriosos passos manuals en el procés i ajudant als enginyers de disseny físic a obtenir millors resultats en menys temps. La primera contribució és el routing "under-the-cell", una proposta per connectar cel·les estàndard usant pins laterals en les capes de metall inferior de manera sistemàtica. L'objectiu és reduir la congestió en les capes de metall superior causades per l'ús de metall i vies, i així disminuir el nombre de violacions de regles de disseny. Per permetre la connexió lateral de cel·les, estenem una llibreria de cel·les estàndard amb dissenys que incorporen connexions laterals. També proposem modificacions locals al placement per permetre explotar aquest tipus de connexions més sovint. Els resultats experimentals mostren una reducció significativa en el nombre de pins, vies i nombre de violacions de regles de disseny, amb un impacte negligible en wirelength i timing. La segona contribució, desenvolupada en col·laboració amb eSilicon (una empresa capdavantera en disseny ASIC), és el desenvolupament de HiDaP, una eina de macro placement per a dissenys industrials actuals. La proposta segueix un procés multinivell per fer el floorplan de blocks jeràrquics, formats per macros i cel·les estàndard. Mitjançant la informació RTL disponible en la netlist, l'afinitat de dataflow entre els mòduls es modela i minimitza per trobar macro placements amb bones propietats de wirelength i timing. La proposta també incorpora la possibilitat de rebre input addicional de l'enginyer, com ara suggeriments de les posicions de les macros. Finalment, també usa mètodes espectrals i de forçes per guiar la cerca de floorplans. Els resultats experimentals mostren que els dissenys generats amb HiDaP són millors que els obtinguts per eines comercials capdavanteres de EDA. Els resultats també mostren que els dissenys presentats poden obtenir un wirelength similar i millor timing que macro placements obtinguts manualment, usats per fabricació. Alguns dissenys obtinguts per HiDaP s'han dut fins a timing-closure en una o dues rondes de modificacions incrementals per part d'enginyers de disseny físic. L'eina s'ha integrat en el procés de disseny de eSilicon i el seu desenvolupament continua més enllà de les aportacions a aquesta tesi.Postprint (published version

AI/ML Algorithms and Applications in VLSI Design and Technology

An evident challenge ahead for the integrated circuit (IC) industry in the nanometer regime is the investigation and development of methods that can reduce the design complexity ensuing from growing process variations and curtail the turnaround time of chip manufacturing. Conventional methodologies employed for such tasks are largely manual; thus, time-consuming and resource-intensive. In contrast, the unique learning strategies of artificial intelligence (AI) provide numerous exciting automated approaches for handling complex and data-intensive tasks in very-large-scale integration (VLSI) design and testing. Employing AI and machine learning (ML) algorithms in VLSI design and manufacturing reduces the time and effort for understanding and processing the data within and across different abstraction levels via automated learning algorithms. It, in turn, improves the IC yield and reduces the manufacturing turnaround time. This paper thoroughly reviews the AI/ML automated approaches introduced in the past towards VLSI design and manufacturing. Moreover, we discuss the scope of AI/ML applications in the future at various abstraction levels to revolutionize the field of VLSI design, aiming for high-speed, highly intelligent, and efficient implementations

Design and Verification of the Data Encryption Standard for ASICs and FPGAs

Encryption and decryption in a communication channel are used to provide security. In this thesis, the Data Encryption Standard (DES) is implemented with both FPGAs and ASICs. Different versions of FPGAs from different synthesis tools are compared. For ASIC implementation, the design space is explored to compile the design with different optimization targets like size, speed and power. Physical realizations of the design are obtained with Cadence tools. Simulations are made at each level to verify the implementations

Affordable techniques for dependable microprocessor design

As high computing power is available at an affordable cost, we rely on microprocessor-based systems for much greater variety of applications. This dependence indicates that a processor failure could have more diverse impacts on our daily lives. Therefore, dependability is becoming an increasingly important quality measure of microprocessors.;Temporary hardware malfunctions caused by unstable environmental conditions can lead the processor to an incorrect state. This is referred to as a transient error or soft error. Studies have shown that soft errors are the major source of system failures. This dissertation characterizes the soft error behavior on microprocessors and presents new microarchitectural approaches that can realize high dependability with low overhead.;Our fault injection studies using RISC processors have demonstrated that different functional blocks of the processor have distinct susceptibilities to soft errors. The error susceptibility information must be reflected in devising fault tolerance schemes for cost-sensitive applications. Considering the common use of on-chip caches in modern processors, we investigated area-efficient protection schemes for memory arrays. The idea of caching redundant information was exploited to optimize resource utilization for increased dependability. We also developed a mechanism to verify the integrity of data transfer from lower level memories to the primary caches. The results of this study show that by exploiting bus idle cycles and the information redundancy, an almost complete check for the initial memory data transfer is possible without incurring a performance penalty.;For protecting the processor\u27s control logic, which usually remains unprotected, we propose a low-cost reliability enhancement strategy. We classified control logic signals into static and dynamic control depending on their changeability, and applied various techniques including commit-time checking, signature caching, component-level duplication, and control flow monitoring. Our schemes can achieve more than 99% coverage with a very small hardware addition. Finally, a virtual duplex architecture for superscalar processors is presented. In this system-level approach, the processor pipeline is backed up by a partially replicated pipeline. The replication-based checker minimizes the design and verification overheads. For a large-scale superscalar processor, the proposed architecture can bring 61.4% reduction in die area while sustaining the maximum performance

Project OASIS: The Design of a Signal Detector for the Search for Extraterrestrial Intelligence

An 8 million channel spectrum analyzer (MCSA) was designed the meet to meet the needs of a SETI program. The MCSA puts out a very large data base at very high rates. The development of a device which follows the MCSA, is presented

New Techniques for On-line Testing and Fault Mitigation in GPUs

L'abstract è presente nell'allegato / the abstract is in the attachmen