Linearity of Outphasing Radio Transmitters

The outphasing transmitter is a promising technique, which can simultaneously achieve high linearity and power efficiency, thereby addressing the major design requirements of next generation transmitters. It employs highly non-linear power amplifier (PA) classes in a linear manner, in principle transmitting a distortion-free signal. Due to symmetric nature of the outphasing architecture, its linearity performance is constrained by any mismatches and non-linear effects encountered in the RF paths. This thesis analyzes the linearity performance of outphasing transmitters (in terms of ACLR specification) for LTE base station applications, under the non-linear effects and tolerances present in practical implementations. The system-level model, built in Matlab software, investigates the important non-linear effects present in outphasing transmitters, including gain and phase imbalance, IQ modulator mismatches, delay imbalance, and the non-linear effects of PAs and Chireix combiners. The path and delay mismatches result in only partial cancellation of the wideband quadrature signal, and thus create interference in both the in-band and out-of-band frequency regions. The misalignment in IQ modulators, such as gain/phase imbalance and carrier leakage, introduces amplitude and phase modulation in the outphased signals. The quadrature modulator mismatches, in conjunction with amplifier nonlinearity, result in spectral regrowth around the carrier frequency. The transmitter linearity performance is also affected by mismatches in the non-linear characteristics of the PAs. Realistic square-wave signals, exhibiting finite rise- and fall- time, also create spectral leakage for distinct rise/fall times in each outphasing branch. Furthermore, the Chireix combiner severely degrades the linearity of outphasing transmitters; it produces ACLR well below the specified limit for LTE base stations. This makes mandatory the compensation of Chireix combiner induced non-linearity in outphasing transmitters. The strict linearity requirements (for LTE downlink applications) present a small tolerance window for mismatches experienced in practical circuits. The relatively small tolerance margin indicates the need of linearization and compensation techniques in outphasing transmitters

A +20dBm highly efficient linear outphasing Class-E PA without AM/AM and AM/PM characterization requirements

Outphasing Class-E Power Amplifiers (OEPAs) using isolating power combiners and an inverse cosine signal component separator are inherently linear but suffer from low efficiency at power back-off. For high efficiency both at maximum output power and at power back-off, non-isolating power combiners are required. In this work the linearity of OEPAs using nonisolating power combiners is studied theoretically and validated by measurement of a 1.8GHz 20dBm OEPA implemented in a standard 65nm CMOS technology using an off-chip transmissionline based combiner. The developed theoretical model for the linearity is then employed to define digital pre-distortion (DPD) parameters for the implemented OEPA. Using this theory-based DPD and without any AM/AM and AM/PM characterizations, -31dB RMS EVM level and below -30dB ACLR were measured for a 13.1dBm 6.25MHz 30Mbit/s 7dB PAPR 64QAM signal with 41.8% drain efficiency and 33.6% power added efficiency

Linear Operation of Switch-Mode Outphasing Power Amplifiers

Radio transceivers are playing an increasingly important role in modern society. The ”connected” lifestyle has been enabled by modern wireless communications. The demand that has been placed on current wireless and cellular infrastructure requires increased spectral efficiency however this has come at the cost of power efficiency. This work investigates methods of improving wireless transceiver efficiency by enabling more efficient power amplifier architectures, specifically examining the role of switch-mode power amplifiers in macro cell scenarios. Our research focuses on the mechanisms within outphasing power amplifiers which prevent linear amplification. From the analysis it was clear that high power non-linear effects are correctable with currently available techniques however non-linear effects around the zero crossing point are not. As a result signal processing techniques for suppressing and avoiding non-linear operation in low power regions are explored. A novel method of digital pre-distortion is presented, and conventional techniques for linearisation are adapted for the particular needs of the outphasing power amplifier. More unconventional signal processing techniques are presented to aid linearisation of the outphasing power amplifier, both zero crossing and bandwidth expansion reduction methods are designed to avoid operation in nonlinear regions of the amplifiers. In combination with digital pre-distortion the techniques will improve linearisation efforts on outphasing systems with dynamic range and bandwidth constraints respectively. Our collaboration with NXP provided access to a digital outphasing power amplifier, enabling empirical analysis of non-linear behaviour and comparative analysis of behavioural modelling and linearisation efforts. The collaboration resulted in a bench mark for linear wideband operation of a digital outphasing power amplifier. The complimentary linearisation techniques, bandwidth expansion reduction and zero crossing reduction have been evaluated in both simulated and practical outphasing test benches. Initial results are promising and indicate that the benefits they provide are not limited to the outphasing amplifier architecture alone. Overall this thesis presents innovative analysis of the distortion mechanisms of the outphasing power amplifier, highlighting the sensitivity of the system to environmental effects. Practical and novel linearisation techniques are presented, with a focus on enabling wide band operation for modern communications standards

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

High efficiency power amplifiers for modern mobile communications: The load-modulation approach

Modern mobile communication signals require power amplifiers able to maintain very high efficiency in a wide range of output power levels, which is a major issue for classical power amplifier architectures. Following the load-modulation approach, efficiency enhancement is achieved by dynamically changing the amplifier load impedance as a function of the input power. In this paper, a review of the widely-adopted Doherty power amplifier and of the other load-modulation efficiency enhancement techniques is presented. The main theoretical aspects behind each method are introduced, and the most relevant practical implementations available in recent literature are reported and discussed

RF Power Amplifier and Its Envelope Tracking

This dissertation introduces an agile supply modulator with optimal transient performance for the envelope tracking supply in linear power amplifiers. For this purpose, an on-demand current source module, the bang-bang transient performance enhancer (BBTPE), is proposed. Its objective is to follow fast variations in input signals with reduced overshoot and settling time without deteriorating the steady-state performance of the buck regulator. The proposed approach enables fast system response through the BBTPE and an accurate steady-state output response through a low switching ripple and power efficient dynamic buck regulator. Fast output response with the help of the added module induces a slower rise of inductor current in the buck converter that further assists the proposed system to reduce both overshoot and settling time. To demonstrate the feasibility of the proposed solution, extensive simulations and experimental results from a discrete system are reported. The proposed supply modulator shows 80% improvement in rise time along with 60% reduction in both overshoot and settling time compared to the conventional dynamic buck regulator-based solution. Experimental results for a PA using the LTE 16-QAM 5 MHz standard shows improvement of 7.68 dB and 65.1% in ACPR and EVM, respectively. In a polar power amplifier, the input signal splits into phase and amplitude components using a non-linear conversion operation. This operation broadens the spectrum of the polar signal components. The information of amplitude and phase contains spectral images due to the sampling operation in non-linear conversion operation. These spectral images can be large and cause out-of-band emission in the output spectrum. In addition, during the recombination process of phase and amplitude, a delay mismatch between amplitude and phase signals, which can occur due to separate processing paths of amplitude and phase signals, causes out-of-band emissions, also known as spectral regrowth. This dissertation presents solutions to both of the issues of digital polar power amplifier: spectral images and delay mismatch. In order to reduce the problem of spectral images, interpolation of phase and amplitude is proposed in this work. This increases the effective sampling frequency of the amplitude and phase, which helps to improve the linearity by around 10 dB. In addition, a novel calibration scheme is proposed here for the delay mismatch between phase and amplitude path in a digital polar power amplifier. The scheme significantly reduces the spectral regrowth. The scheme uses the same path for phase and amplitude delay calculation after the recombination that allows having a robust calibration. Furthermore, it can be executed during the empty transmission slots. The proposed scheme is designed in a 40 nm CMOS technology and simulated with a 64-QAM IEEE 802.11n wireless standard. The scheme achieved 7.57 dB enhancement in ACLR and 84.35% improvement in EVM for a 3.5 ns mismatch in phase and amplitude path

Wideband CMOS Data Converters for Linear and Efficient mmWave Transmitters

With continuously increasing demands for wireless connectivity, higher\ua0carrier frequencies and wider bandwidths are explored. To overcome a limited transmit power at these higher carrier frequencies, multiple\ua0input multiple output (MIMO) systems, with a large number of transmitters\ua0and antennas, are used to direct the transmitted power towards\ua0the user. With a large transmitter count, each individual transmitter\ua0needs to be small and allow for tight integration with digital circuits. In\ua0addition, modern communication standards require linear transmitters,\ua0making linearity an important factor in the transmitter design.In this thesis, radio frequency digital-to-analog converter (RF-DAC)-based transmitters are explored. They shift the transition from digital\ua0to analog closer to the antennas, performing both digital-to-analog\ua0conversion and up-conversion in a single block. To reduce the need for\ua0computationally costly digital predistortion (DPD), a linear and wellbehaved\ua0RF-DAC transfer characteristic is desirable. The combination\ua0of non-overlapping local oscillator (LO) signals and an expanding segmented\ua0non-linear RF-DAC scaling is evaluated as a way to linearize\ua0the transmitter. This linearization concept has been studied both for\ua0the linearization of the RF-DAC itself and for the joint linearization of\ua0the cascaded RF-DAC-based modulator and power amplifier (PA) combination.\ua0To adapt the linearization, observation receivers are needed.\ua0In these, high-speed analog-to-digital converters (ADCs) have a central\ua0role. A high-speed ADC has been designed and evaluated to understand\ua0how concepts used to increase the sample rate affect the dynamic performance

Theory and Implementation of RF-Input Outphasing Power Amplification

Conventional outphasing power amplifier systems require both a radio frequency (RF) carrier input and a separate baseband input to synthesize a modulated RF output. This work presents an RF-input/RF-output outphasing power amplifier that directly amplifies a modulated RF input, eliminating the need for multiple costly IQ modulators and baseband signal component separation as in previous outphasing systems. An RF signal decomposition network directly synthesizes the phase- and amplitude-modulated signals used to drive the branch power amplifiers (PAs). With this approach, a modulated RF signal including zero-crossings can be applied to the single RF input port of the outphasing RF amplifier system. The proposed technique is demonstrated at 2.14 GHz in a four-way lossless outphasing amplifier with transmission-line power combiner. The RF decomposition network is implemented using a transmission-line resistance compression network with nonlinear loads designed to provide the necessary amplitude and phase decomposition. The resulting proof-of-concept outphasing power amplifier has a peak CW output power of 93 W, peak drain efficiency of 70%, and performance on par with a previously-demonstrated outphasing and power combining system requiring four IQ modulators and a digital signal component separator

Multi-Band Outphasing Power Amplifier Design for Mobile and Base Stations

New generations of wireless communication systems require linear efficient RF power amplifiers (PAs) for higher transmission data rates and longer battery life. On the contrary, conventional PAs are normally designed for peak efficiency under maximum output power (Pout). Thus, in power back-off, the overall efficiency degrades significantly and the average efficiency is much lower than the efficiency at maximum Pout. Chireix outphasing PA, also called LINC (Linear amplification using Non-linear Components), is one of the most promising techniques to improve the efficiency at power back-off. In this method, a variable envelope input signal is first decomposed into two constant-envelope phase-modulated signals and then amplified using two highly efficient non-linear PAs. The output signals are combined preferably in a loss-less power combiner to build the desired output signal. In this way, the PA exhibits high efficiency with good linearity. In this thesis, first we analyze a complex model of outphasing combiner considering its nonidealities such as reflection and loss in transmission lines (TL). Then we propose a compact model with analytical formula that is validated through several comparative tests using ADS and Spectre RF. Furthermore, we analyze the effect of reactive load in Chireix combiner with stubs (a parallel inductor and capacitor), while distinguishing between its capacitive and inductive parts. It is demonstrated that only the capacitive part of the reactive load degrades the performances. Based on this, a new architecture (Z LINC) is proposed where the power combiner is designed to provide a zero capacitive load to the PAs whatever the outphasing angle. The theory describing the operations of the system is developed and a 900 MHz classical LINC and Z-LINC PAs are designed and measured. In addition, a miniaturization technique is proposed which employs λ/8 or smaller TLs instead of conventional λ/4 TLs in outphasing power combiner. This technique is applied to implement a 900 MHz PA using LDMOS power transistors. Besides single-band PAs, dual-band PAs are more and more needed because of an increasing demand for wireless communication terminals to handle multi-band operation. In chapter 5, a new compact design approach for dual-band transmitters based on a reconfigurable outphasing combiner is proposed. The objective is to avoid the cumbersome implementations where several PAs and matching network are used in parallel. The technique is applied to design a dual band PA with a fully integrated power combiner in 90 nm CMOS technology. An inverter-based class D PA topology, particularly suitable for outphasing and multimode operations is presented. The TLs in the combiner, realized using a network of on-chip series inductors and parallel capacitors, are reconfigurable from λ/4 in 1800 MHz to λ/8 in 900 MHz. In order to maximize the efficiency, the on-chip inductors are implemented using high quality factor on chip slab inductors. The measured maximum Pout at 900/1800 MHz are 24.3 and 22.7 dBm with maximum efficiencies of 51% and 34% respectively