Low-Power, High-Speed Transceivers for Network-on-Chip Communication

Networks on chips (NoCs) are becoming popular as they provide a solution for the interconnection problems on large integrated circuits (ICs). But even in a NoC, link-power can become unacceptably high and data rates are limited when conventional data transceivers are used. In this paper, we present a low-power, high-speed source-synchronous link transceiver which enables a factor 3.3 reduction in link power together with an 80% increase in data-rate. A low-swing capacitive pre-emphasis transmitter in combination with a double-tail sense-amplifier enable speeds in excess of 9 Gb/s over a 2 mm twisted differential interconnect, while consuming only 130 fJ/transition without the need for an additional supply. Multiple transceivers can be connected back-to-back to create a source-synchronous transceiver-chain with a wave-pipelined clock, operating with 6sigma offset reliability at 5 Gb/s

A low-power quadrature digital modulator in 0.18um CMOS

Quadrature digital modulation techniques are widely used in modern communication systems because of their high performance and flexibility. However, these advantages come at the cost of high power consumption. As a result, power consumption has to be taken into account as a main design factor of the modulator.In this thesis, a low-power quadrature digital modulator in 0.18um CMOS is presented with the target system clock speed of 150 MHz. The quadrature digital modulator consists of several key blocks: quadrature direct digital synthesizer (QDDS), pulse shaping filter, interpolation filter and inverse sinc filter. The design strategy is to investigate different implementations for each block and compare the power consumption of these implementations. Based on the comparison results, the implementation that consumes the lowest power will be chosen for each block. First of all, a novel low-power QDDS is proposed in the thesis. Power consumption estimation shows that it can save up to 60% of the power consumption at 150 MHz system clock frequency compared with one conventional design. Power consumption estimation results also show that using two pulse shaping blocks to process I/Q data, cascaded integrator comb (CIC) interpolation structure, and inverse sinc filter with modified canonic signed digit (MCSD) multiplication consume less power than alternative design choices. These low-power blocks are integrated together to achieve a low-power modulator. The power consumption estimation after layout shows that it only consumes about 95 mW at 150 MHz system clock rate, which is much lower than similar commercial products. The designed modulator can provide a low-power solution for various quadrature modulators. It also has an output bandwidth from 0 to 75 MHz, configurable pulse shaping filters and interpolation filters, and an internal sin(x)/x correction filter

A COMPREHENSIVE OVERVIEW OF RECENT DEVELOPMENTS IN RF-MEMS TECHNOLOGY-BASED HIGH-PERFORMANCE PASSIVE COMPONENTS FOR APPLICATIONS IN THE 5G AND FUTURE TELECOMMUNICATIONS SCENARIOS

The goal of this work is to provide an overview about the current development of radio-frequency microelectromechanical systems technology, with special attention towards those passive components bearing significant application potential in the currently developing 5G paradigm. Due to the required capabilities of such communication standard in terms of high data rates, extended allocated spectrum, use of massive MIMO (Multiple-Input-Multiple-Output) systems, beam steering and beam forming, the focus will be on devices like switches, phase shifters, attenuators, filters, and their packaging/integration. For each of the previous topics, several valuable contributions appeared in the last decade, underlining the improvements produced in the state of the art and the chance for RF-MEMS technology to play a prominent role in the actual implementation of the 5G infrastructure

Reinventing Integrated Photonic Devices and Circuits for High Performance Communication and Computing Applications

The long-standing technological pillars for computing systems evolution, namely Moore\u27s law and Von Neumann architecture, are breaking down under the pressure of meeting the capacity and energy efficiency demands of computing and communication architectures that are designed to process modern data-centric applications related to Artificial Intelligence (AI), Big Data, and Internet-of-Things (IoT). In response, both industry and academia have turned to \u27more-than-Moore\u27 technologies for realizing hardware architectures for communication and computing. Fortunately, Silicon Photonics (SiPh) has emerged as one highly promising ‘more-than-Moore’ technology. Recent progress has enabled SiPh-based interconnects to outperform traditional electrical interconnects, offering advantages like high bandwidth density, near-light speed data transfer, distance-independent bitrate, and low energy consumption. Furthermore, SiPh-based electro-optic (E-O) computing circuits have exhibited up to two orders of magnitude improvements in performance and energy efficiency compared to their electronic counterparts. Thus, SiPh stands out as a compelling solution for creating high-performance and energy-efficient hardware for communication and computing applications. Despite their advantages, SiPh-based interconnects face various design challenges that hamper their reliability, scalability, performance, and energy efficiency. These include limited optical power budget (OPB), high static power dissipation, crosstalk noise, fabrication and on-chip temperature variations, and limited spectral bandwidth for multiplexing. Similarly, SiPh-based E-O computing circuits also face several challenges. Firstly, the E-O circuits for simple logic functions lack the all-electrical input handling, raising hardware area and complexity. Secondly, the E-O arithmetic circuits occupy vast areas (at least 100x) while hardly achieving more than 60% hardware utilization, versus CMOS implementations, leading to high idle times, and non-amortizable area and static power overheads. Thirdly, the high area overhead of E-O circuits hinders them from achieving high spatial parallelism on-chip. This is because the high area overhead limits the count of E-O circuits that can be implemented on a reticle-size limited chip. My research offers significant contributions to address the aforementioned challenges. For SiPh-based interconnects, my contributions focus on enhancing OPB by mitigating crosstalk noise, addressing the optical non-linearity-related issues through the development of Silicon-on-Sapphire-based photonic interconnects, exploring multi-level signaling, and evaluating various device-level design pathways. This enables the design of high throughput (\u3e1Tbps) and energy-efficient (\u3c1pJ/bit) SiPh interconnects. In the context of SiPh-based E-O circuits, my contributions include the design of a microring-based polymorphic E-O logic gate, a hybrid time-amplitude analog optical modulator, and an indium tin oxide-based silicon nitride microring modulator and a weight bank for neural network computations. These designs significantly reduce the area overhead of current E-O computing circuits while enhancing the energy-efficiency, and hardware utilization

Silicon Photonic Subsystems for Inter-Chip Optical Networks

The continuous growth of electronic compute and memory nodes in terms of the number of I/O pins, bandwidth, and areal throughput poses major integration and packaging challenges associated with offloading multi-Tbit/s data rates within the few pJ/bit targets. While integrated photonics are already deployed in long and short distances such as inter and intra data centers communications, the promising characteristics of the silicon photonic platform set it as the future technology for optical interconnects in ultra short inter-chip distances. The high index contrast between the waveguide and the cladding together with strong thermo-optic and carrier effects in silicon allows developing a wide range of micro-scale and low power optical devices compatible with the CMOS fabrication processes. Furthermore, the availability of photonic foundries and new electrical and optical co-packaging techniques further pushes this platform for the next steps of commercial deployment. The work in this dissertation presents the current trends in high-performance memory and processor nodes and gives motivation for disaggregated and reconfigurable inter-chip network enabled with the silicon photonic layer. A dense WDM transceiver and broadband switch architectures are discussed to support a bi-directional network of ten hybrid-memory cubes (HMC) interconnected to ten processor nodes with an overall aggregated bandwidth of 9.6Tbit/s. Latency and energy consumption are key performance parameters in a processor to primary memory nodes connectivity. The transceiver design is based on energy-efficient micro-ring resonators, and the broadband switch is constructed with 2x2 Mach-Zehnder elements for nano-second reconfiguration. Each transceiver is based on hundreds of micro-rings to convert the native HMC electrical protocol to the optical domain and the switch is based on tens of hundreds of 2x2 elements to achieve non-blocking all-to-all connectivity. The next chapters focus on developing methods for controlling and monitoring such complex and highly integrated silicon photonic subsystems. The thermo-optic effect is characterized and we show experimentally that the phase of the optical carrier can be reliably controlled with pulse-width modulation (PWM) signal, ultimately relaxing the need for hundreds of digital to analog converters (DACs). We further show that doped waveguide heaters can be utilized as \textit{in-line} optical power monitors by measuring photo-conductance current, which is an alternative for the conventional tapping and integration of photo-diodes. The next part concerned with a common cascaded micro-ring resonator in a WDM transceiver design. We develop on an FPGA control algorithm that abstracts the physical layer and takes user-defined inputs to set the resonances to the desired wavelength in a unicast and multicast transmission modes. The associated sensitivities of these silicon ring resonators are presented and addressed with three closed-loop solutions. We first show a closed-loop operation based on tapping the error signal from the drop port of the micro-ring. The second solution presents a resonance wavelength locking with a single digital I/O for control and feedback signals. Lastly, we leverage the photo-conductance effect and demonstrate the locking procedure using only the doped heater for both control and feedback purposes. To achieve the inter-chip reconfigurability we discuss recent advances of high-port-count SiP broadband switches for reconfigurable inter-chip networks. To ensure optimal operation in terms of low insertion loss, low cross-talk and high signal integrity per routing path, hundreds of 2x2 Mach-Zehnder elements need to be biased precisely for the cross and bar states. We address this challenge with a tapless and a design agnostic calibration approach based on the photo-conductance effect. The automated algorithm returns a look-up table for all for each 2x2 element and the associated calibrated biases. Each routing scenario is then tested for insertion loss, crosstalk and bit-error rate of 25Gbit/s 4-level pulse amplitude modulation signals. The last part utilizes the Mach-Zehnder interferometers in WDM transceiver applications. We demonstrate a polarization insensitive four-channel WDM receiver with 40Gbit/s per channel and a transmitter design generating 8-level pulse amplitude modulation signals at 30Gbit/s

A Hybrid Method of Performing Electric Power System Fault Ride-Through Evaluations on Medium Voltage Multi-Megawatt Devices

This dissertation explores the design and analysis of a Hybrid Method of performing electrical power system fault ride-through evaluations on multi-megawatt, medium voltage power conversion equipment. Fault ride-through evaluations on such equipment are needed in order to verify and validate full scale designs prior to being implemented in the field. Ultimately, these evaluations will help in reducing the deployment risks associated with bringing new technologies into the marketplace. This is especially true for renewable energy and utility scale energy storage systems, where a significant amount of attention in recent years has focused on their ever increasing role in power system security and stability. The Hybrid Method couples two existing technologies together - a reactive voltage divider network and a power electronic variable voltage source - in order to overcome the inherent limitation of both methods, namely the short circuit duty required for implementation. This work provides the background of this limitation with respect to the existing technologies and demonstrates that the Hybrid Method can minimize the fault duty required for fault evaluations. The physical system, control objectives, and operation cycle of the Hybrid Method are analyzed with respect to the overall objective of reducing the fault duty of the system. A vector controller is designed to incorporate the time variant nature of the Hybrid Method operation cycle, limit the fault current seen by the power electronic variable voltage source, and provide regulation of the voltage at the point of common coupling with the device being evaluated. In order to verify the operation of both the Hybrid Method physical system and vector controller, a controller hardware-in-the-loop experiment is created in order to simulate the physical system in real-time against the prototype implementation of the vector controller. The physical system is simulated in a Real Time Digital Simulator and is controlled with the Hybrid Method vector controller implemented on a National Instruments FPGA. In order to evaluate the complete performance of the Hybrid Method, both a synchronous generator and a doubly-fed induction generator are modeled as the device under test in the simulations of the physical system. Finally, the results of the controller hardware-in-the-loop experiments are presented which demonstrate that the Hybrid Method is a viable solution to performing fault ride-through evaluations on multi-megawatt, medium voltage power conversion equipment

Wireless tools for neuromodulation

Epilepsy is a spectrum of diseases characterized by recurrent seizures. It is estimated that 50 million individuals worldwide are affected and 30% of cases are medically refractory or drug resistant. Vagus nerve stimulation (VNS) and deep brain stimulation (DBS) are the only FDA approved device based therapies. Neither therapy offers complete seizure freedom in a majority of users. Novel methodologies are needed to better understand mechanisms and chronic nature of epilepsy. Most tools for neuromodulation in rodents are tethered. The few wireless devices use batteries or are inductively powered. The tether restricts movement, limits behavioral tests, and increases the risk of infection. Batteries are large and heavy with a limited lifetime. Inductive powering suffers from rapid efficiency drops due to alignment mismatches and increased distances. Miniature wireless tools that offer behavioral freedom, data acquisition, and stimulation are needed. This dissertation presents a platform of electrical, optical and radiofrequency (RF) technologies for device based neuromodulation. The platform can be configured with features including: two channels differential recording, one channel electrical stimulation, and one channel optical stimulation. Typical device operation consumes less than 4 mW. The analog front end has a bandwidth of 0.7 Hz - 1 kHz and a gain of 60 dB, and the constant current driver provides biphasic electrical stimulation. For use with optogenetics, the deep brain optical stimulation module provides 27 mW/mm2 of blue light (473 nm) with 21.01 mA. Pairing of stimulating and recording technologies allows closed-loop operation. A wireless powering cage is designed using the resonantly coupled filter energy transfer (RCFET) methodology. RF energy is coupled through magnetic resonance. The cage has a PTE ranging from 1.8-6.28% for a volume of 11 x 11 x 11 in3. This is sufficient to chronically house subjects. The technologies are validated through various in vivo preparations. The tools are designed to study epilepsy, SUDEP, and urinary incontinence but can be configured for other studies. The broad application of these technologies can enable the scientific community to better study chronic diseases and closed-loop therapies

Reconfigurable Receiver Front-Ends for Advanced Telecommunication Technologies

The exponential growth of converging technologies, including augmented reality, autonomous vehicles, machine-to-machine and machine-to-human interactions, biomedical and environmental sensory systems, and artificial intelligence, is driving the need for robust infrastructural systems capable of handling vast data volumes between end users and service providers. This demand has prompted a significant evolution in wireless communication, with 5G and subsequent generations requiring exponentially improved spectral and energy efficiency compared to their predecessors. Achieving this entails intricate strategies such as advanced digital modulations, broader channel bandwidths, complex spectrum sharing, and carrier aggregation scenarios. A particularly challenging aspect arises in the form of non-contiguous aggregation of up to six carrier components across the frequency range 1 (FR1). This necessitates receiver front-ends to effectively reject out-of-band (OOB) interferences while maintaining high-performance in-band (IB) operation. Reconfigurability becomes pivotal in such dynamic environments, where frequency resource allocation, signal strength, and interference levels continuously change. Software-defined radios (SDRs) and cognitive radios (CRs) emerge as solutions, with direct RF-sampling receivers offering a suitable architecture in which the frequency translation is entirely performed in digital domain to avoid analog mixing issues. Moreover, direct RF- sampling receivers facilitate spectrum observation, which is crucial to identify free zones, and detect interferences. Acoustic and distributed filters offer impressive dynamic range and sharp roll off characteristics, but their bulkiness and lack of electronic adjustment capabilities limit their practicality. Active filters, on the other hand, present opportunities for integration in advanced CMOS technology, addressing size constraints and providing versatile programmability. However, concerns about power consumption, noise generation, and linearity in active filters require careful consideration.This thesis primarily focuses on the design and implementation of a low-voltage, low-power RFFE tailored for direct sampling receivers in 5G FR1 applications. The RFFE consists of a balun low-noise amplifier (LNA), a Q-enhanced filter, and a programmable gain amplifier (PGA). The balun-LNA employs noise cancellation, current reuse, and gm boosting for wideband gain and input impedance matching. Leveraging FD-SOI technology allows for programmable gain and linearity via body biasing. The LNA's operational state ranges between high-performance and high-tolerance modes, which are apt for sensitivityand blocking tests, respectively. The Q-enhanced filter adopts noise-cancelling, current-reuse, and programmable Gm-cells to realize a fourth-order response using two resonators. The fourth-order filter response is achieved by subtracting the individual response of these resonators. Compared to cascaded and magnetically coupled fourth-order filters, this technique maintains the large dynamic range of second-order resonators. Fabricated in 22-nm FD-SOI technology, the RFFE achieves 1%-40% fractional bandwidth (FBW) adjustability from 1.7 GHz to 6.4 GHz, 4.6 dB noise figure (NF) and an OOB third-order intermodulation intercept point (IIP3) of 22 dBm. Furthermore, concerning the implementation uncertainties and potential variations of temperature and supply voltage, design margins have been considered and a hybrid calibration scheme is introduced. A combination of on-chip and off-chip calibration based on noise response is employed to effectively adjust the quality factors, Gm-cells, and resonance frequencies, ensuring desired bandpass response. To optimize and accelerate the calibration process, a reinforcement learning (RL) agent is used.Anticipating future trends, the concept of the Q-enhanced filter extends to a multiple-mode filter for 6G upper mid-band applications. Covering the frequency range from 8 to 20 GHz, this RFFE can be configured as a fourth-order dual-band filter, two bandpass filters (BPFs) with an OOB notch, or a BPF with an IB notch. In cognitive radios, the filter’s transmission zeros can be positioned with respect to the carrier frequencies of interfering signals to yield over 50 dB blocker rejection