12,654 research outputs found
Improving latency tolerance of multithreading through decoupling
The increasing hardware complexity of dynamically scheduled superscalar processors may compromise the scalability of this organization to make an efficient use of future increases in transistor budget. SMT processors, designed over a superscalar core, are therefore directly concerned by this problem. The article presents and evaluates a novel processor microarchitecture which combines two paradigms: simultaneous multithreading and access/execute decoupling. Since its decoupled units issue instructions in order, this architecture is significantly less complex, in terms of critical path delays, than a centralized out-of-order design, and it is more effective for future growth in issue-width and clock speed. We investigate how both techniques complement each other. Since decoupling features an excellent memory latency hiding efficiency, the large amount of parallelism exploited by multithreading may be used to hide the latency of functional units and keep them fully utilized. The study shows that, by adding decoupling to a multithreaded architecture, fewer threads are needed to achieve maximum throughput. Therefore, in addition to the obvious hardware complexity reduction, it places lower demands on the memory system. The study also reveals that multithreading by itself exhibits little memory latency tolerance. Results suggest that most of the latency hiding effectiveness of SMT architectures comes from the dynamic scheduling. On the other hand, decoupling is very effective at hiding memory latency. An increase in the cache miss penalty from 1 to 32 cycles reduces the performance of a 4-context multithreaded decoupled processor by less than 2 percent. For the nondecoupled multithreaded processor, the loss of performance is about 23 percent.Peer ReviewedPostprint (published version
A case for merging the ILP and DLP paradigms
The goal of this paper is to show that instruction level parallelism (ILP) and data-level parallelism (DLP) can be merged in a single architecture to execute vectorizable code at a performance level that can not be achieved using either paradigm on its own. We will show that the combination of the two techniques yields very high performance at a low cost and a low complexity. We will show that this architecture can reach a performance equivalent to a superscalar processor that sustained 10 instructions per cycle. We will see that the machine exploiting both types of parallelism improves upon the ILP-only machine by factors of 1.5-1.8. We also present a study on the scalability of both paradigms and show that, when we increase resources to reach a 16-issue machine, the advantage of the ILP+DLP machine over the ILP-only machine increases up to 2.0-3.45. While the peak achieved IPC for the ILP machine is 4, the ILP+DLP machine exceeds 10 instructions per cycle.Peer ReviewedPostprint (published version
Desynchronization: Synthesis of asynchronous circuits from synchronous specifications
Asynchronous implementation techniques, which measure logic delays at run time and activate registers accordingly, are inherently more robust than their synchronous counterparts, which estimate worst-case delays at design time, and constrain the clock cycle accordingly. De-synchronization is a new paradigm to automate the design of asynchronous circuits from synchronous specifications, thus permitting widespread adoption of asynchronicity, without requiring special design skills or tools. In this paper, we first of all study different protocols for de-synchronization and formally prove their correctness, using techniques originally developed for distributed deployment of synchronous language specifications. We also provide a taxonomy of existing protocols for asynchronous latch controllers, covering in particular the four-phase handshake protocols devised in the literature for micro-pipelines. We then propose a new controller which exhibits provably maximal concurrency, and analyze the performance of desynchronized circuits with respect to the original synchronous optimized implementation. We finally prove the feasibility and effectiveness of our approach, by showing its application to a set of real designs, including a complete implementation of the DLX microprocessor architectur
Software trace cache
We explore the use of compiler optimizations, which optimize the layout of instructions in memory. The target is to enable the code to make better use of the underlying hardware resources regardless of the specific details of the processor/architecture in order to increase fetch performance. The Software Trace Cache (STC) is a code layout algorithm with a broader target than previous layout optimizations. We target not only an improvement in the instruction cache hit rate, but also an increase in the effective fetch width of the fetch engine. The STC algorithm organizes basic blocks into chains trying to make sequentially executed basic blocks reside in consecutive memory positions, then maps the basic block chains in memory to minimize conflict misses in the important sections of the program. We evaluate and analyze in detail the impact of the STC, and code layout optimizations in general, on the three main aspects of fetch performance; the instruction cache hit rate, the effective fetch width, and the branch prediction accuracy. Our results show that layout optimized, codes have some special characteristics that make them more amenable for high-performance instruction fetch. They have a very high rate of not-taken branches and execute long chains of sequential instructions; also, they make very effective use of instruction cache lines, mapping only useful instructions which will execute close in time, increasing both spatial and temporal locality.Peer ReviewedPostprint (published version
Commercial-off-the-shelf simulation package interoperability: Issues and futures
Commercial-Off-The-Shelf Simulation Packages (CSPs) are widely used in industry to simulate discrete-event models. Interoperability of CSPs requires the use of distributed simulation techniques. Literature presents us with many examples of achieving CSP interoperability using bespoke solutions. However, for the wider adoption of CSP-based distributed simulation it is essential that, first and foremost, a standard for CSP interoperability be created, and secondly, these standards are adhered to by the CSP vendors. This advanced tutorial is on an emerging standard relating to CSP interoperability. It gives an overview of this standard and presents case studies that implement some of the proposed standards. Furthermore, interoperability is discussed in relation to large and complex models developed using CSPs that require large amount of computing resources. It is hoped that this tutorial will inform the simulation community of the issues associated with CSP interoperability, the importance of these standards and its future
Fault-Tolerant Adaptive Parallel and Distributed Simulation
Discrete Event Simulation is a widely used technique that is used to model
and analyze complex systems in many fields of science and engineering. The
increasingly large size of simulation models poses a serious computational
challenge, since the time needed to run a simulation can be prohibitively
large. For this reason, Parallel and Distributes Simulation techniques have
been proposed to take advantage of multiple execution units which are found in
multicore processors, cluster of workstations or HPC systems. The current
generation of HPC systems includes hundreds of thousands of computing nodes and
a vast amount of ancillary components. Despite improvements in manufacturing
processes, failures of some components are frequent, and the situation will get
worse as larger systems are built. In this paper we describe FT-GAIA, a
software-based fault-tolerant extension of the GAIA/ART\`IS parallel simulation
middleware. FT-GAIA transparently replicates simulation entities and
distributes them on multiple execution nodes. This allows the simulation to
tolerate crash-failures of computing nodes; furthermore, FT-GAIA offers some
protection against byzantine failures since synchronization messages are
replicated as well, so that the receiving entity can identify and discard
corrupted messages. We provide an experimental evaluation of FT-GAIA on a
running prototype. Results show that a high degree of fault tolerance can be
achieved, at the cost of a moderate increase in the computational load of the
execution units.Comment: Proceedings of the IEEE/ACM International Symposium on Distributed
Simulation and Real Time Applications (DS-RT 2016
Model evaluation, recommendation and prioritizing of future work for the manipulator emulator testbed
The Manipulator Emulator Testbed (MET) is to provide a facility capable of hosting the simulation of various manipulator configurations to support concept studies, evaluation, and other engineering development activities. Specifically, the testbed is intended to support development of the Space Station Remote Manipulator System (SSRMS) and related systems. The objective of this study is to evaluate the math models developed for the MET simulation of a manipulator's rigid body dynamics and the servo systems for each of the driven manipulator joints. Specifically, the math models are examined with regard to their amenability to pipeline and parallel processing. Based on this evaluation and the project objectives, a set of prioritized recommendations are offered for future work
- …