On Co-Optimization Of Constrained Satisfiability Problems For Hardware Software Applications

Manufacturing technology has permitted an exponential growth in transistor count and density. However, making efficient use of the available transistors in the design has become exceedingly difficult. Standard design flow involves synthesis, verification, placement and routing followed by final tape out of the design. Due to the presence of various undesirable effects like capacitive crosstalk, supply noise, high temperatures, etc., verification/validation of the design has become a challenging problem. Therefore, having a good design convergence may not be possible within the target time, due to a need for a large number of design iterations. Capacitive crosstalk is one of the major causes of design convergence problems in deep sub-micron era. With scaling, the number of crosstalk violations has been increasing because of reduced inter-wire distances. Consequently only the most severe crosstalk faults are fixed pre-silicon while the rest are tested post-silicon. Testing for capacitive crosstalk involves generation of input patterns which can be applied post-silicon to the integrated circuit and comparison of the output response. These patterns are generated at the gate/ Register Transfer Level (RTL) of abstraction using Automatic Test Pattern Generation (ATPG) tools. In this dissertation, anInteger Linear Programming (ILP) based ATPG technique for maximizing crosstalk induced delay increase at the victim net, for multiple aggressor crosstalk faults, is presented. Moreover, various solutions for pattern generation considering both zero as well as unit delay models is also proposed. With voltage scaling, power supply switching noise has become one of the leading causes of signal integrity related failures in deep sub-micron designs. Hence, during power supply network design and analysis of power supply switching noise, computation of peak supply current is an essential step. Traditional peak current estimation approaches involve addition of peak current associated with all the CMOS gates which are switching in a combinational circuit. Consequently, this approach does not take the Boolean and temporal relationships of the circuit into account. This work presents an ILP based technique for generation of an input pattern pair which maximizes switching supply currents for a combinational circuit in the presence of integer gate delays. The input pattern pair generated using the above approach can be applied post-silicon for power droop testing. With high level of integration, Multi-Processor Systems on Chip (MPSoC) feature multiple processor cores and accelerators on the same die, so as to exploit the instruction level parallelism in the application. For hardware-software co-design, application programming model is based on a Task Graph, which represents task dependencies and execution/transfer times for various threads and processes within an application. Mapping an application to an MPSoC traditionally involves representing it in the form of a task graph and employing static scheduling in order to minimize the schedule length. Dynamic system behavior is not taken into consideration during static scheduling, while dynamic scheduling requires the knowledge of task graph at runtime. A run-time task graph extraction heuristic to facilitate dynamic scheduling is also presented here. A novel game theory based approach uses this extracted task graph to perform run-time scheduling in order to minimize total schedule length. With increase in transistor density, power density has gone up substantially. This has lead to generation of regions with very high temperature called Hotspots. Hotspots lead to reliability and performance issues and affect design convergence. In current generation Integrated Circuits (ICs) temperature is controlled by reducing power dissipation using Dynamic Thermal Management (DTM) techniques like frequency and/or voltage scaling. These techniques are reactive in nature and have detrimental effects on performance. Here, a look-ahead based task migration technique is proposed, in order to utilize the multitude of cores available in an MPSoC to eliminate thermal emergencies. Our technique is based on temperature prediction, leveraging upon a novel wavelet based thermal modeling approach. Hence, this work addresses several optimization problems that can be reduced to constrained max-satisfiability, involving integer as well as Boolean constraints in hardware and software domains. Moreover, it provides domain specific heuristic solutions for each of them

Nonlinear Load Compensation

Nonlinear loads pose significant problems to power engineers, and have proliferated in occurrence over the past few decades. This project seeks to design and simulate a process by which one might mitigate the harmful consequences that result from their usage, employing signals processing techniques, logical decision-making processes, and currently available power electronics hardware

Robust low-power digital circuit design in nano-CMOS technologies

Device scaling has resulted in large scale integrated, high performance, low-power, and low cost systems. However the move towards sub-100 nm technology nodes has increased variability in device characteristics due to large process variations. Variability has severe implications on digital circuit design by causing timing uncertainties in combinational circuits, degrading yield and reliability of memory elements, and increasing power density due to slow scaling of supply voltage. Conventional design methods add large pessimistic safety margins to mitigate increased variability, however, they incur large power and performance loss as the combination of worst cases occurs very rarely. In-situ monitoring of timing failures provides an opportunity to dynamically tune safety margins in proportion to on-chip variability that can significantly minimize power and performance losses. We demonstrated by simulations two delay sensor designs to detect timing failures in advance that can be coupled with different compensation techniques such as voltage scaling, body biasing, or frequency scaling to avoid actual timing failures. Our simulation results using 45 nm and 32 nm technology BSIM4 models indicate significant reduction in total power consumption under temperature and statistical variations. Future work involves using dual sensing to avoid useless voltage scaling that incurs a speed loss. SRAM cache is the first victim of increased process variations that requires handcrafted design to meet area, power, and performance requirements. We have proposed novel 6 transistors (6T), 7 transistors (7T), and 8 transistors (8T)-SRAM cells that enable variability tolerant and low-power SRAM cache designs. Increased sense-amplifier offset voltage due to device mismatch arising from high variability increases delay and power consumption of SRAM design. We have proposed two novel design techniques to reduce offset voltage dependent delays providing a high speed low-power SRAM design. Increasing leakage currents in nano-CMOS technologies pose a major challenge to a low-power reliable design. We have investigated novel segmented supply voltage architecture to reduce leakage power of the SRAM caches since they occupy bulk of the total chip area and power. Future work involves developing leakage reduction methods for the combination logic designs including SRAM peripherals

Modeling and Analysis of Noise and Interconnects for On-Chip Communication Link Design

This thesis considers modeling and analysis of noise and interconnects in onchip communication. Besides transistor count and speed, the capabilities of a modern design are often limited by on-chip communication links. These links typically consist of multiple interconnects that run parallel to each other for long distances between functional or memory blocks. Due to the scaling of technology, the interconnects have considerable electrical parasitics that affect their performance, power dissipation and signal integrity. Furthermore, because of electromagnetic coupling, the interconnects in the link need to be considered as an interacting group instead of as isolated signal paths. There is a need for accurate and computationally effective models in the early stages of the chip design process to assess or optimize issues affecting these interconnects. For this purpose, a set of analytical models is developed for on-chip data links in this thesis. First, a model is proposed for modeling crosstalk and intersymbol interference. The model takes into account the effects of inductance, initial states and bit sequences. Intersymbol interference is shown to affect crosstalk voltage and propagation delay depending on bus throughput and the amount of inductance. Next, a model is proposed for the switching current of a coupled bus. The model is combined with an existing model to evaluate power supply noise. The model is then applied to reduce both functional crosstalk and power supply noise caused by a bus as a trade-off with time. The proposed reduction method is shown to be effective in reducing long-range crosstalk noise. The effects of process variation on encoded signaling are then modeled. In encoded signaling, the input signals to a bus are encoded using additional signaling circuitry. The proposed model includes variation in both the signaling circuitry and in the wires to calculate the total delay variation of a bus. The model is applied to study level-encoded dual-rail and 1-of-4 signaling. In addition to regular voltage-mode and encoded voltage-mode signaling, current-mode signaling is a promising technique for global communication. A model for energy dissipation in RLC current-mode signaling is proposed in the thesis. The energy is derived separately for the driver, wire and receiver termination.Siirretty Doriast

Impacts of midpoint FACTS controllers on the coordiantion between generator phase backup protection and generator capability limits

The thesis reports the results of comprehensive studies carried out to explore the impact of midpoint FACTS Controllers (STATCOM and SVC) on the generator distance phase backup protection in order to identify important issues that protection engineers need to consider when designing and setting a generator protection system. In addition, practical, feasible and simple solutions to mitigate the adverse impact of midpoint FACTS Controllers on the generator distance phase backup protection are explored. The results of these studies show that midpoint FACTS Controllers have an adverse effect on the generator distance phase backup protection. This adverse effect, which can be in the form of underreach, overreach or a time delay, varies according to the fault type, fault location and generator loading. Moreover, it has been found that the adverse effect of the midpoint FACTS Controllers extends to affect the coordination between the generator distance phase backup protection and the generator steady-state overexcited capability limit. The Support Vector Machines classification technique is proposed as a replacement for the existing generator distance phase backup protection relay in order to alleviate potential problems. It has been demonstrated that this technique is a very promising solution, as it is fast, reliable and has a high performance efficiency. This will result in enhancing the coordination between the generator phase backup protection and the generator steady-state overexcited capability limit in the presence of midpoint FACTS Controllers. The thesis also presents the results of investigations carried out to explore the impact of the generator distance phase backup protection relay on the generator overexcitation thermal capability. The results of these investigations reveal that with the relay settings according to the current standards, the generator is over-protected and the generator distance phase backup protection relay restricts the generator overexcitation thermal capability during system disturbances. This restriction does not allow the supply of the maximum reactive power of the generating unit during such events. The restriction on the generator overexcitation thermal capability caused by the generator distance phase backup protection relay highlights the necessity to revise the relay settings. The proposed solution in this thesis is to reduce the generator distance phase backup protection relay reach in order to provide secure performance during system disturbances

A verilog-based simulation methodology for estimating power and area

Accurate modeling and estimating of the power dissipation in the early stages of the design flow is becoming more important, as the aggressive scaling of transistors results in higher leakage currents. New and complex systems are being implemented using highly advanced Electronic Design Automation (EDA) tools. As the complexity increases, the dissipation of power has emerged as one of the very significant design constraints. Low power designs are not only used in small size applications like cell phones and handheld devices but also in high-performance computing applications. Numerous tools have emerged in recent years to address this issue of power consumption and power optimization. With a vast number of these power measurement tools emerging, analyzing power consumed by digital circuits has not only become easier but also more effective methods are deployed to optimize digital circuits to dissipate less power. In this work, we present a Verilog-based technique to estimate an accurate power dissipation of a design considering the state-dependency of the leakage power and path dependency of dynamic power. We develop the verilog models of cells which trace the probability of the static levels of the signals in the course of a simulation. Then, these data are used to calculate the power dissipation in the overall design. The power dissipation of some benchmark circuits is estimated using the proposed approach

Quantifiable Assurance: From IPs to Platforms

Hardware vulnerabilities are generally considered more difficult to fix than software ones because they are persistent after fabrication. Thus, it is crucial to assess the security and fix the vulnerabilities at earlier design phases, such as Register Transfer Level (RTL) and gate level. The focus of the existing security assessment techniques is mainly twofold. First, they check the security of Intellectual Property (IP) blocks separately. Second, they aim to assess the security against individual threats considering the threats are orthogonal. We argue that IP-level security assessment is not sufficient. Eventually, the IPs are placed in a platform, such as a system-on-chip (SoC), where each IP is surrounded by other IPs connected through glue logic and shared/private buses. Hence, we must develop a methodology to assess the platform-level security by considering both the IP-level security and the impact of the additional parameters introduced during platform integration. Another important factor to consider is that the threats are not always orthogonal. Improving security against one threat may affect the security against other threats. Hence, to build a secure platform, we must first answer the following questions: What additional parameters are introduced during the platform integration? How do we define and characterize the impact of these parameters on security? How do the mitigation techniques of one threat impact others? This paper aims to answer these important questions and proposes techniques for quantifiable assurance by quantitatively estimating and measuring the security of a platform at the pre-silicon stages. We also touch upon the term security optimization and present the challenges for future research directions

Design for Reliability and Low Power in Emerging Technologies

Die fortlaufende Verkleinerung von Transistor-Strukturgrößen ist einer der wichtigsten Antreiber für das Wachstum in der Halbleitertechnologiebranche. Seit Jahrzehnten erhöhen sich sowohl Integrationsdichte als auch Komplexität von Schaltkreisen und zeigen damit einen fortlaufenden Trend, der sich über alle modernen Fertigungsgrößen erstreckt. Bislang ging das Verkleinern von Transistoren mit einer Verringerung der Versorgungsspannung einher, was zu einer Reduktion der Leistungsaufnahme führte und damit eine gleichbleibenden Leistungsdichte sicherstellte. Doch mit dem Beginn von Strukturgrößen im Nanometerbreich verlangsamte sich die fortlaufende Skalierung. Viele Schwierigkeiten, sowie das Erreichen von physikalischen Grenzen in der Fertigung und Nicht-Idealitäten beim Skalieren der Versorgungsspannung, führten zu einer Zunahme der Leistungsdichte und, damit einhergehend, zu erschwerten Problemen bei der Sicherstellung der Zuverlässigkeit. Dazu zählen, unter anderem, Alterungseffekte in Transistoren sowie übermäßige Hitzeentwicklung, nicht zuletzt durch stärkeres Auftreten von Selbsterhitzungseffekten innerhalb der Transistoren. Damit solche Probleme die Zuverlässigkeit eines Schaltkreises nicht gefährden, werden die internen Signallaufzeiten üblicherweise sehr pessimistisch kalkuliert. Durch den so entstandenen zeitlichen Sicherheitsabstand wird die korrekte Funktionalität des Schaltkreises sichergestellt, allerdings auf Kosten der Performance. Alternativ kann die Zuverlässigkeit des Schaltkreises auch durch andere Techniken erhöht werden, wie zum Beispiel durch Null-Temperatur-Koeffizienten oder Approximate Computing. Wenngleich diese Techniken einen Großteil des üblichen zeitlichen Sicherheitsabstandes einsparen können, bergen sie dennoch weitere Konsequenzen und Kompromisse. Bleibende Herausforderungen bei der Skalierung von CMOS Technologien führen außerdem zu einem verstärkten Fokus auf vielversprechende Zukunftstechnologien. Ein Beispiel dafür ist der Negative Capacitance Field-Effect Transistor (NCFET), der eine beachtenswerte Leistungssteigerung gegenüber herkömmlichen FinFET Transistoren aufweist und diese in Zukunft ersetzen könnte. Des Weiteren setzen Entwickler von Schaltkreisen vermehrt auf komplexe, parallele Strukturen statt auf höhere Taktfrequenzen. Diese komplexen Modelle benötigen moderne Power-Management Techniken in allen Aspekten des Designs. Mit dem Auftreten von neuartigen Transistortechnologien (wie zum Beispiel NCFET) müssen diese Power-Management Techniken neu bewertet werden, da sich Abhängigkeiten und Verhältnismäßigkeiten ändern. Diese Arbeit präsentiert neue Herangehensweisen, sowohl zur Analyse als auch zur Modellierung der Zuverlässigkeit von Schaltkreisen, um zuvor genannte Herausforderungen auf mehreren Designebenen anzugehen. Diese Herangehensweisen unterteilen sich in konventionelle Techniken ((a), (b), (c) und (d)) und unkonventionelle Techniken ((e) und (f)), wie folgt: $\textbf{(a)}$ Analyse von Leistungszunahmen in Zusammenhang mit der Maximierung von Leistungseffizienz beim Betrieb nahe der Transistor Schwellspannung, insbesondere am optimalen Leistungspunkt. Das genaue Ermitteln eines solchen optimalen Leistungspunkts ist eine besondere Herausforderung bei Multicore Designs, da dieser sich mit den jeweiligen Optimierungszielsetzungen und der Arbeitsbelastung verschiebt. $\textbf{(b)}$ Aufzeigen versteckter Interdependenzen zwischen Alterungseffekten bei Transistoren und Schwankungen in der Versorgungsspannung durch „IR-drops“. Eine neuartige Technik wird vorgestellt, die sowohl Über- als auch Unterschätzungen bei der Ermittlung des zeitlichen Sicherheitsabstands vermeidet und folglich den kleinsten, dennoch ausreichenden Sicherheitsabstand ermittelt. $\textbf{(c)}$ Eindämmung von Alterungseffekten bei Transistoren durch „Graceful Approximation“, eine Technik zur Erhöhung der Taktfrequenz bei Bedarf. Der durch Alterungseffekte bedingte zeitlich Sicherheitsabstand wird durch Approximate Computing Techniken ersetzt. Des Weiteren wird Quantisierung verwendet um ausreichend Genauigkeit bei den Berechnungen zu gewährleisten. $\textbf{(d)}$ Eindämmung von temperaturabhängigen Verschlechterungen der Signallaufzeit durch den Betrieb nahe des Null-Temperatur Koeffizienten (N-ZTC). Der Betrieb bei N-ZTC minimiert temperaturbedingte Abweichungen der Performance und der Leistungsaufnahme. Qualitative und quantitative Vergleiche gegenüber dem traditionellen zeitlichen Sicherheitsabstand werden präsentiert. $\textbf{(e)}$ Modellierung von Power-Management Techniken für NCFET-basierte Prozessoren. Die NCFET Technologie hat einzigartige Eigenschaften, durch die herkömmliche Verfahren zur Spannungs- und Frequenzskalierungen zur Laufzeit (DVS/DVFS) suboptimale Ergebnisse erzielen. Dies erfordert NCFET-spezifische Power-Management Techniken, die in dieser Arbeit vorgestellt werden. $\textbf{(f)}$ Vorstellung eines neuartigen heterogenen Multicore Designs in NCFET Technologie. Das Design beinhaltet identische Kerne; Heterogenität entsteht durch die Anwendung der individuellen, optimalen Konfiguration der Kerne. Amdahls Gesetz wird erweitert, um neue system- und anwendungsspezifische Parameter abzudecken und die Vorzüge des neuen Designs aufzuzeigen. Die Auswertungen der vorgestellten Techniken werden mithilfe von Implementierungen und Simulationen auf Schaltkreisebene (gate-level) durchgeführt. Des Weiteren werden Simulatoren auf Systemebene (system-level) verwendet, um Multicore Designs zu implementieren und zu simulieren. Zur Validierung und Bewertung der Effektivität gegenüber dem Stand der Technik werden analytische, gate-level und system-level Simulationen herangezogen, die sowohl synthetische als auch reale Anwendungen betrachten

PV System Information Enhancement and Better Control of Power Systems.

abstract: Due to the rapid penetration of solar power systems in residential areas, there has been a dramatic increase in bidirectional power flow. Such a phenomenon of bidirectional power flow creates a need to know where Photovoltaic (PV) systems are located, what their quantity is, and how much they generate. However, significant challenges exist for accurate solar panel detection, capacity quantification, and generation estimation by employing existing methods, because of the limited labeled ground truth and relatively poor performance for direct supervised learning. To mitigate these issue, this thesis revolutionizes key learning concepts to (1) largely increase the volume of training data set and expand the labelled data set by creating highly realistic solar panel images, (2) boost detection and quantification learning through physical knowledge and (3) greatly enhance the generation estimation capability by utilizing effective features and neighboring generation patterns. These techniques not only reshape the machine learning methods in the GIS domain but also provides a highly accurate solution to gain a better understanding of distribution networks with high PV penetration. The numerical validation and performance evaluation establishes the high accuracy and scalability of the proposed methodologies on the existing solar power systems in the Southwest region of the United States of America. The distribution and transmission networks both have primitive control methodologies, but now is the high time to work out intelligent control schemes based on reinforcement learning and show that they can not only perform well but also have the ability to adapt to the changing environments. This thesis proposes a sequence task-based learning method to create an agent that can learn to come up with the best action set that can overcome the issues of transient over-voltage.Dissertation/ThesisMasters Thesis Electrical Engineering 201