The control of space manipulators subject to spacecraft attitude control saturation limits

The motions of robotic manipulators mounted on spacecraft can disturb the spacecraft's positions and attitude. These disturbances can surpass the ability of the system's attitude control reaction jets to control them, for the disturbances increase as manipulator speeds increase. If the manipulator moves too quickly the resulting disturbances can exceed the saturation levels of the reaction jets, causing excessive spacecraft motions. A method for planning space manipulator's motions is presented, so that tasks can be performed as quickly as possible without saturating the system's attitude control jets

Dynamics and Motion of a Six Degree of Freedom Robot Manipulator

In this thesis, a strategy to accomplish pick-and-place operations using a six degree-of-freedom (DOF) robotic arm attached to a wheeled mobile robot is presented. This research work is part of a bigger project in developing a robotic-assisted nursing to be used in medical settings. The significance of this project relies on the increasing demand for elderly and disabled skilled care assistance which nowadays has become insufficient. Strong efforts have been made to incorporate technology to fulfill these needs. Several methods were implemented to make a 6-DOF manipulator capable of performing pick-and-place operations. Some of these methods were used to achieve specific tasks such as: solving the inverse kinematics problem, or planning a collision-free path. Other methods, such as forward kinematics description, workspace evaluation, and dexterity analysis, were used to describe the manipulator and its capabilities. The manipulator was accurately described by obtaining the link transformation matrices from each joint using the Denavit-Hartenberg (DH) notations. An Iterative Inverse Kinematics method (IIK) was used to find multiple configurations for the manipulator along a given path. The IIK method was based on the specific geometric characteristic of the manipulator, in which several joints share a common plane. To find admissible solutions along the path, the workspace of the manipulator was considered. Algebraic formulations to obtain the specific workspace of the 6-DOF manipulator on the Cartesian coordinate space were derived from the singular configurations of the manipulator. Local dexterity analysis was also required to identify possible orientations of the end-effector for specific Cartesian coordinate positions. The closed-form expressions for the range of such orientations were derived by adapting an existing dexterity method. Two methods were implemented to plan the free-collision path needed to move an object from one place to another without colliding with an obstacle. Via-points were added to avoid the robot mobile platform and the zones in which the manipulator presented motion difficulties. Finally, the segments located between initial, final, and via-points positions, were connected using straight lines forming a global path. To form the collision-free path, the straight-line were modified to avoid the obstacles that intersected the path. The effectiveness of the proposed analysis was verified by comparing simulation and experimental results. Three predefined paths were used to evaluate the IIK method. Ten different scenarios with different number and pattern of obstacles were used to verify the efficiency of the entire path planning algorithm. Overall results confirmed the efficiency of the implemented methods for performing pick-and-place operations with a 6-DOF manipulator

Evaluation of automated decisionmaking methodologies and development of an integrated robotic system simulation

A generic computer simulation for manipulator systems (ROBSIM) was implemented and the specific technologies necessary to increase the role of automation in various missions were developed. The specific items developed are: (1) capability for definition of a manipulator system consisting of multiple arms, load objects, and an environment; (2) capability for kinematic analysis, requirements analysis, and response simulation of manipulator motion; (3) postprocessing options such as graphic replay of simulated motion and manipulator parameter plotting; (4) investigation and simulation of various control methods including manual force/torque and active compliances control; (5) evaluation and implementation of three obstacle avoidance methods; (6) video simulation and edge detection; and (7) software simulation validation

Kinematics, controls, and path planning results for a redundant manipulator

The inverse kinematics solution, a modal position control algorithm, and path planning results for a 7 degree of freedom manipulator are presented. The redundant arm consists of two links with shoulder and elbow joints and a spherical wrist. The inverse kinematics problem for tip position is solved and the redundant joint is identified. It is also shown that a locus of tip positions exists in which there are kinematic limitations on self-motion. A computationally simple modal position control algorithm has been developed which guarantees a nearly constant closed-loop dynamic response throughout the workspace. If all closed-loop poles are assigned to the same location, the algorithm can be implemented with very little computation. To further reduce the required computation, the modal gains are updated only at discrete time intervals. Criteria are developed for the frequency of these updates. For commanding manipulator movements, a 5th-order spline which minimizes jerk provides a smooth tip-space path. Schemes for deriving a corresponding joint-space trajectory are discussed. Modifying the trajectory to avoid joint torque saturation when a tip payload is added is also considered. Simulation results are presented

Collision-free inverse kinematics of the redundant seven-link manipulator used in a cucumber picking robot

The paper presents results of research on an inverse kinematics algorithm that has been used in a functional model of a cucumber-harvesting robot consisting of a redundant P6R manipulator. Within a first generic approach, the inverse kinematics problem was reformulated as a non-linear programming problem and solved with a Genetic Algorithm (GA). Although solutions were easily obtained, the considerable calculation time needed to solve the problem prevented on-line implementation. To circumvent this problem, a second, less generic, approach was developed which consisted of a mixed numerical-analytic solution of the inverse kinematics problem exploiting the particular structure of the P6R manipulator. Using the latter approach, calculation time was considerably reduced. During the early stages of the cucumber-harvesting project, this inverse kinematics algorithm was used off-line to evaluate the ability of the robot to harvest cucumbers using 3D-information obtained from a cucumber crop in a real greenhouse. Thereafter, the algorithm was employed successfully in a functional model of the cucumber harvester to determine if cucumbers were hanging within the reachable workspace of the robot and to determine a collision-free harvest posture to be used for motion control of the manipulator during harvesting. The inverse kinematics algorithm is presented and demonstrated with some illustrative examples of cucumber harvesting, both off-line during the design phase as well as on-line during a field test

Autonomous space processor for orbital debris

The development of an Autonomous Space Processor for Orbital Debris (ASPOD) was the goal. The nature of this craft, which will process, in situ, orbital debris using resources available in low Earth orbit (LEO) is explained. The serious problem of orbital debris is briefly described and the nature of the large debris population is outlined. The focus was on the development of a versatile robotic manipulator to augment an existing robotic arm, the incorporation of remote operation of the robotic arms, and the formulation of optimal (time and energy) trajectory planning algorithms for coordinated robotic arms. The mechanical design of the new arm is described in detail. The work envelope is explained showing the flexibility of the new design. Several telemetry communication systems are described which will enable the remote operation of the robotic arms. The trajectory planning algorithms are fully developed for both the time optimal and energy optimal problems. The time optimal problem is solved using phase plane techniques while the energy optimal problem is solved using dynamic programming