Transformer based front-end for a low power 2.4 GHz transceiver

A low power transceiver architecture for the 2.4 GHz ISM band using a 1.0 V supply is presented. It employs a transformer to convert the 100 Ω antenna impedance to almost 1 kΩ and so facilitates a low power transmitter and receiver. The simulated post-layout output power of the differential class-E power amplifier is 2.0 dBm with a drain efficiency of 28.4%. The direct-conversion receiver achieves a very low power consumption of 420 μW and a noise figure of 15.0 dB.Ministerio de Ciencia e Innovación TEC2009-08447Junta de Andalucía TIC-0281

Ultra Small Antenna and Low Power Receiver for Smart Dust Wireless Sensor Networks

Wireless Sensor Networks have the potential for profound impact on our daily lives. Smart Dust Wireless Sensor Networks (SDWSNs) are emerging members of the Wireless Sensor Network family with strict requirements on communication node sizes (1 cubic centimeter) and power consumption (< 2mW during short on-states). In addition, the large number of communication nodes needed in SDWSN require highly integrated solutions. This dissertation develops new design techniques for low-volume antennas and low-power receivers for SDWSN applications. In addition, it devises an antenna and low noise amplifier co-design methodology to increase the level of design integration, reduce receiver noise, and reduce the development cycle. This dissertation first establishes stringent principles for designing SDWSN electrically small antennas (ESAs). Based on these principles, a new ESA, the F-Inverted Compact Antenna (FICA), is designed at 916MHz. This FICA has a significant advantage in that it uses a small-size ground plane. The volume of this FICA (including the ground plane) is only 7% of other state-of-the-art ESAs, while its efficiency (48.53%) and gain (-1.38dBi) are comparable to antennas of much larger dimensions. A physics-based circuit model is developed for this FICA to assist system level design at the earliest stage, including optimization of the antenna performance. An antenna and low noise amplifier (LNA) co-design method is proposed and proven to be valid to design low power LNAs with the very low noise figure of only 1.5dB. To reduce receiver power consumption, this dissertation proposes a novel LNA active device and an input/ouput passive matching network optimization method. With this method, a power efficient high voltage gain cascode LNA was designed in a 0.13um CMOS process with only low quality factor inductors. This LNA has a 3.6dB noise figure, voltage gain of 24dB, input third intercept point (IIP3) of 3dBm, and power consumption of 1.5mW at 1.0V supply voltage. Its figure of merit, using the typical definition, is twice that of the best in the literature. A full low power receiver is developed with a sensitivity of -58dBm, chip area of 1.1mm2, and power consumption of 2.85mW

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Millimeter-Wave and Terahertz Transceivers in SiGe BiCMOS Technologies

This invited paper reviews the progress of silicon–germanium (SiGe) bipolar-complementary metal–oxide–semiconductor (BiCMOS) technology-based integrated circuits (ICs) during the last two decades. Focus is set on various transceiver (TRX) realizations in the millimeter-wave range from 60 GHz and at terahertz (THz) frequencies above 300 GHz. This article discusses the development of SiGe technologies and ICs with the latter focusing on the commercially most important applications of radar and beyond 5G wireless communications. A variety of examples ranging from 77-GHz automotive radar to THz sensing as well as the beginnings of 60-GHz wireless communication up to THz chipsets for 100-Gb/s data transmission are recapitulated. This article closes with an outlook on emerging fields of research for future advancement of SiGe TRX performance

Ultra-Low Power Wake Up Receiver For Medical Implant Communications Service Transceiver

This thesis explores the specific requirements and challenges for the design of a dedicated wake-up receiver for medical implant communication services equipped with a novel “uncertain-IF†architecture combined with a high – Q filtering MEMS resonator and a free running CMOS ring oscillator as the RF LO. The receiver prototype, implements an IBM 0.18μm mixed-signal 7ML RF CMOS technology and achieves a sensitivity of -62 dBm at 404MHz while consuming \u3c100 μW from a 1 V supply

Low power CMOS IC, biosensor and wireless power transfer techniques for wireless sensor network application

The emerging field of wireless sensor network (WSN) is receiving great attention due to the interest in healthcare. Traditional battery-powered devices suffer from large size, weight and secondary replacement surgery after the battery life-time which is often not desired, especially for an implantable application. Thus an energy harvesting method needs to be investigated. In addition to energy harvesting, the sensor network needs to be low power to extend the wireless power transfer distance and meet the regulation on RF power exposed to human tissue (specific absorption ratio). Also, miniature sensor integration is another challenge since most of the commercial sensors have rigid form or have a bulky size. The objective of this thesis is to provide solutions to the aforementioned challenges

ULTRA LOW POWER FSK RECEIVER AND RF ENERGY HARVESTER

This thesis focuses on low power receiver design and energy harvesting techniques as methods for intelligently managing energy usage and energy sources. The goal is to build an inexhaustibly powered communication system that can be widely applied, such as through wireless sensor networks (WSNs). Low power circuit design and smart power management are techniques that are often used to extend the lifetime of such mobile devices. Both methods are utilized here to optimize power usage and sources. RF energy is a promising ambient energy source that is widely available in urban areas and which we investigate in detail. A harvester circuit is modeled and analyzed in detail at low power input. Based on the circuit analysis, a design procedure is given for a narrowband energy harvester. The antenna and harvester co-design methodology improves RF to DC energy conversion efficiency. The strategy of co-design of the antenna and the harvester creates opportunities to optimize the system power conversion efficiency. Previous surveys have found that ambient RF energy is spread broadly over the frequency domain; however, here it is demonstrated that it is theoretically impossible to harvest RF energy over a wide frequency band if the ambient RF energy source(s) are weak, owing to the voltage requirements. It is found that most of the ambient RF energy lies in a series of narrow bands. Two different versions of harvesters have been designed, fabricated, and tested. The simulated and measured results demonstrate a dual-band energy harvester that obtains over 9% efficiency for two different bands (900MHz and 1800MHz) at an input power as low as -19dBm. The DC output voltage of this harvester is over 1V, which can be used to recharge the battery to form an inexhaustibly powered communication system. A new phase locked loop based receiver architecture is developed to avoid the significant conversion losses associated with OOK architectures. This also helps to minimize power consumption. A new low power mixer circuit has also been designed, and a detailed analysis is provided. Based on the mixer, a low power phase locked loop (PLL) based receiver has been designed, fabricated and measured. A power management circuit and a low power transceiver system have also been co-designed to provide a system on chip solution. The low power voltage regulator is designed to handle a variety of battery voltage, environmental temperature, and load conditions. The whole system can work with a battery and an application specific integrated circuit (ASIC) as a sensor node of a WSN network

A Fully-Integrated Quad-Band GSM/GPRS CMOS Power Amplifier

Concentric distributed active transformers (DAT) are used to implement a fully-integrated quad-band power amplifier (PA) in a standard 130 nm CMOS process. The DAT enables the power amplifier to integrate the input and output matching networks on the same silicon die. The PA integrates on-chip closed-loop power control and operates under supply voltages from 2.9 V to 5.5 V in a standard micro-lead-frame package. It shows no oscillations, degradation, or failures for over 2000 hours of operation with a supply of 6 V at 135° under a VSWR of 15:1 at all phase angles and has also been tested for more than 2 million device-hours (with ongoing reliability monitoring) without a single failure under nominal operation conditions. It produces up to +35 dBm of RF power with power-added efficiency of 51%