Innovative Wireless Power Receiver for Inductive Coupling and Magnetic Resonance Applications

This chapter presents a wireless power receiver for inductive coupling and magnetic resonance applications. The active rectifier with shared delay-locked loop (DLL) is proposed to achieve the high efficiency for different operation frequencies. In the DC–DC converter, the phase-locked loop is adopted for the constant switching frequency in the process, voltage, and temperature variation to solve the efficiency reduction problem, which results in the heat problem. An automatic mode switching between pulse width modulation and pulse frequency modulation is also adopted for the high efficiency over the wide output power. This chip is implemented using 0.18 μm BCD technology with an active area of 5.0 mm × 3.5 mm. The maximum efficiency of the active rectifier is 92%, and the maximum efficiency of the DC–DC converter is 92% when the load current is 700 mA

Design of Power Receiving Units for 6.78MHz Wireless Power Transfer Systems

In the last decade, the wireless power transfer (WPT) technology has been a popular topic in power electronics research and increasingly adopted by consumers. The AirFuel WPT standard utilizes resonant coils to transfer energy at 6.78 MHz, introducing many benefits such as longer charging distance, multi-device charging, and high tolerance of the coil misalignment. However, variations in coil coupling due to the change in receiving coil positions alter the equivalent load reactance, degrading efficiency. In recent studies, active full-bridge rectifiers are employed on WPT receivers because of their superior efficiency, controllability, and ability to compensate for detuned WPT networks. In order to take advantage of those characteristics, the rectifier switching actions must be synchronized with the magnetic field. In the literature, existing solutions for synchronizing the active rectifier in WPT systems are mostly not reliable and bulky, which is not suitable for small receivers. Therefore, a frequency synchronous rectifier with compact on-board control is proposed in this thesis. The rectifier power stage is designed to deliver 40 W to the load while achieving full zero-voltage switching to minimize the loss. The inherent feedback from the power stage dynamics to the sensed signal is analyzed to design stable and robust synchronization control, even at a low power of 0.02 W. The control system is accomplished using commercial components, including a low-cost microcontroller, which eliminates the need for bulky control and external sensing hardware. This high power density design allows the receiver to be integrated into daily consumer electronics such as laptops and monitors. Finally, a wide-range and high v resolution control scheme of the rectifier input phase is proposed to enable the dynamic impedance matching capability, maintaining high system efficiency over wide loading conditions. In addition, to increase the WPT technology adoption to low-power consumer electronics, a small wireless receiver replacing conventional AA batteries is developed. This receiver can supply power to existing AA battery-powered devices while providing the benefit of WPT technologies to consumers

A GaN-Based Synchronous Rectifier with Reduced Voltage Distortion for 6.78 MHz Wireless Power Applications

The call for a larger degree of engineering innovation grows as wireless power transfer increases in popularity. In this thesis, 6.78 MHz resonant wireless power transfer is explained. Challenges in WPT such as dynamic load variation and electromagnetic interference due to harmonic distortion are discussed, and a literature review is conducted to convey how the current state of the art is addressing these challenges.A GaN-based synchronous rectifier is proposed as a viable solution, and a model of the circuit is constructed. The precisely derived model is compared to a linearized model to illustrate the importance of exactness within the model derivation. The model is then used to quantify the design space of circuit parameters Lr and Cr with regard to harmonic distortion, input phase control, and efficiency. Practical design decisions concerning the 6.78 MHz system are explained. These include gate driver choice and mitigation of PCB parasitics. The model is verified with open loop experimentation using a linear power amplifier, FPGA, electronic load, and two function generators. Current zero-crossing sensing is then introduced in order to achieve self-regulation of both the switching frequency and input phase. The details of the FPGA code and sensing scheme used to obtain this closed loop functionality are described in detail. Finally, conclusions are drawn, and future work is identified

Wireless Power Transfer

Wireless power transfer techniques have been gaining researchers' and industry attention due to the increasing number of battery-powered devices, such as mobile computers, mobile phones, smart devices, intelligent sensors, mainly as a way to replace the standard cable charging, but also for powering battery-less equipment. The storage capacity of batteries is an extremely important element of how a device can be used. If we talk about battery-powered electronic equipment, the autonomy is one factor that may be essential in choosing a device or another, making the solution of remote powering very attractive. A distinction has to be made between the two forms of wireless power transmission, as seen in terms of how the transmitted energy is used at the receiving point: - Transmission of information or data, when it is essential for an amount of energy to reach the receiver to restore the transmitted information; - Transmission of electric energy in the form of electromagnetic field, when the energy transfer efficiency is essential, the power being used to energize the receiving equipment. The second form of energy transfer is the subject of this book

High Efficiency Power Management Unit for Implantable Optical-Electrical Stimulators

Battery-less active implantable devices are of interest because they offer longer life span and eliminate costly battery replacement surgical interventions. This is possible as a result of advances in inductive power transfer and development of power management circuits to maximize the overall power transfer and provide various voltage levels for multi-functional implantable devices. Rehabilitation therapy using optical stimulation of genetically modified peripheral neurons requires high current loads. Standard rectification topologies are inefficient and have associated voltage drops unsuited for miniaturized implants. This paper presents an integrated power management unit (PMU) for an optical-electrical stimulator to be used in the treatment of motor neurone disease. It includes a power-efficient regulating rectifier with a novel body biased high-speed comparator providing 3.3 V for the operation of the stimulator, a 3-stage latch-up charge pump with 12 V output for the input stage of the optical-electrical stimulator, and 1.8 V for digital control logic. The chip was fabricated in a 0.18 μm CMOS process. Measured results show that for a regulated output of 3.3 V delivering 30.3 mW power, the peak power conversion efficiency is 84.2% at 6.78 MHz inductive link tunable frequency reducing to 70.3% at 13.56 MHz. The charge pump with on chip capacitors has 90.9% measured voltage conversion efficiency

GaN-Based High Efficiency Transmitter for Multiple-Receiver Wireless Power Transfer

Wireless power transfer (WPT) has attracted great attention from industry and academia due to high charging flexibility. However, the efficiency of WPT is lower and the cost is higher than the wired power transfer approaches. Efforts including converter optimization, power delivery architecture improvement, and coils have been made to increase system efficiency.In this thesis, new power delivery architectures in the WPT of consumer electronics have been proposed to improve the overall system efficiency and increase the power density.First, a two-stage transmitter architecture is designed for a 100 W WPT system. After comparing with other topologies, the front-end ac-dc power factor correction (PFC) rectifier employs a totem-pole rectifier. A full bridge 6.78 MHz resonant inverter is designed for the subsequent stage. An impedance matching network provides constant transmitter coil current. The experimental results verify the high efficiency, high PF, and low total harmonic distortion (THD).Then, a single-stage transmitter is derived based on the verified two-stage structure. By integration of the PFC rectifier and full bridge inverter, two GaN FETs are saved and high efficiency is maintained. The integrated DCM operated PFC rectifier provides high PF and low THD. By adopting a control scheme, the transmitter coil current and power are regulated. A simple auxiliary circuit is employed to improve the light load efficiency. The experimental results verify the achievement of high efficiency.A closed-loop control scheme is implemented in the single-stage transmitter to supply multiple receivers simultaneously. With a controlled constant transmitter current, the system provides a smooth transition during dynamically load change. ZVS detection circuit is proposed to protect the transmitter from continuous hard switching operation. The control scheme is verified in the experiments.The multiple-reciever WPT system with the single-stage transmitter is investigated. The system operating range is discussed. The method of tracking optimum system efficiency is studied. The system control scheme and control procedure, targeting at providing a wide system operating range, robust operation and capability of tracking the optimized system efficiency, are proposed. Experiment results demonstrate the WPT system operation

A 6.78MHz Adaptive-ZVS Class-D PA with Dynamic Dead-Time for Wireless Power Transfer system

Department of Electrical EngineeringIn this thesis, a class-D power amplifier (PA) with adaptive zero-voltage switching (A-ZVS) technique for Low power 6.78 MHz resonant wireless power transfer (R-WPT) system is proposed. In R-WPT operation, the loading impedance of a PA can be varied by the process tolerance of the LC resonant components and WPT environments, such as the resonant topology, coupling coefficient and loading condition of the receiver. The proposed A-ZVS feedback loop of PA calibrates the equivalent resonant capacitance using PWM-controlled switched capacitor in real-time to achieve ZVS by adjusting the loading impedance to be slightly inductive. Furthermore, the proposed PA adjust the dead-time according to variation of WPT environments. The proposed PA was fully integrated except for one switched capacitor used as the tuning element and fabricated in a TSMC 0.18um BCD process. The measurement results demonstrated robust ZVS operation with a peak system efficiency of 52.7% and an enhanced maximum transmitting power of 107%.ope

Inductively Coupled CMOS Power Receiver For Embedded Microsensors

Inductively coupled power transfer can extend the lifetime of embedded microsensors that save costs, energy, and lives. To expand the microsensors' functionality, the transferred power needs to be maximized. Plus, the power receiver needs to handle wide coupling variations in real applications. Therefore, the objective of this research is to design a power receiver that outputs the highest power for the widest coupling range. This research proposes a switched resonant half-bridge power stage that adjusts both energy transfer frequency and duration so the output power is maximally high. A maximum power point (MPP) theory is also developed to predict the optimal settings of the power stage with 98.6% accuracy. Finally, this research addresses the system integration challenges such as synchronization and over-voltage protection. The fabricated self-synchronized prototype outputs up to 89% of the available power across 0.067%~7.9% coupling range. The output power (in percentage of available power) and coupling range are 1.3× and 13× higher than the comparable state of the arts.Ph.D

Design and Control of Power Converters 2019

In this book, 20 papers focused on different fields of power electronics are gathered. Approximately half of the papers are focused on different control issues and techniques, ranging from the computer-aided design of digital compensators to more specific approaches such as fuzzy or sliding control techniques. The rest of the papers are focused on the design of novel topologies. The fields in which these controls and topologies are applied are varied: MMCs, photovoltaic systems, supercapacitors and traction systems, LEDs, wireless power transfer, etc