A robust high-efficiency cross-coupled charge pump circuit without blocking transistors

This document is the Accepted Manuscript version of the following article: Minglin Ma, Xinglong Cai, Yichuang Sun, and Nike George, ‘A robust high-efficiency cross-coupled charge pump circuit without blocking transistors’, Analog Integrated Circuits and Signal Processing, Vol. 95 (3): 395-401, June 2018. Under embargo until 16 March 2019. The final publication is available at Springer via: https://doi.org/10.1007/s10470-018-1149-xA fully integrated cross-coupled charge pump circuit with a new clock scheme has been presented in this paper. The new clock scheme ensures that all NMOS pre-charge transistors are turned off when the voltages of main clock signals are high. Notably, all PMOS transfer transistors will be turned off when the voltages of the main clock signals are low. As a result, the charge pump eliminates all of the reversion power loss and reduces the ripple voltage. The proposed charge pump has a better performance even in scenarios where the main clock signals are mismatched. The proposed charge pump circuit was simulated using spectre in the TSMC 0.18 µm CMOS process. The simulation results show that the proposed charge pump circuit has a high voltage conversion efficiency and low ripple voltage.Peer reviewe

A High Efficiency and Low Ripple Cross-Coupled Charge Pump Circuit

A fully integrated cross-coupled charge pump circuit with four-clock signals and a new method of body bias have been proposed. The new clock scheme eliminates all of the reversion power loss and reduces the ripple voltage. In addition, the largest voltage differences between the terminals of all transistors do not exceed the supply voltage. We have also solved the gate-oxide overstress problem in the conventional charge pump circuits and enhanced the reliability. The proposed charge pump circuit has been simulated using Spectre and in the TSMC 0.18um CMOS process. The simulation results show that the maximum voltage conversion efficiency of the new 3-stage cross-coupled circuit with an input voltage of 1.5V is 99.8%. Moreover, the output ripple voltage has been significantly reduced.Peer reviewe

High-efficiency high voltage hybrid charge pump design with an improved chip area

A hybrid charge pump was developed in a 0.13- $\mu \text{m}$ Bipolar-CMOS-DMOS (BCD) process which utilised high drain-source voltage MOS devices and low-voltage integrated metal-insulator-metal (MIM) capacitors. The design consisted of a zero-reversion loss cross-coupled stage and a new self-biased serial-parallel charge pump design. The latter has been shown to have an area reduction of 60% in comparison to a Schottky diode-based Dickson charge pump operating at the same frequency. Post-layout simulations were carried out which demonstrated a peak efficiency of 38% at the output voltage of 18.5 V; the maximum specified output voltage of 27 V was also achieved. A standalone serial-parallel charge pump was shown to have a better transient response and a flatter efficiency curve; these are preferable for time-sensitive applications with a requirement of a broader range of output currents. These findings have significant implications for reducing the total area of implantable high-voltage devices without sacrificing charge pump efficiency or maximum output voltage

Energy-Efficient Start-up Power Management for Batteryless Biomedical Implant Devices

This paper presents a solar energy harvesting power management using the high-efficiency switched capacitor DC-DC converter for biomedical implant applications. By employing an on-chip start-up circuit with parallel connected Photovoltaic (PV) cells, a small efficiency improvement can be obtained when compared with the traditional stacked photodiode methodology to boost the harvested voltage while preserving a single-chip solution. The PV cells have been optimised in the PC1D software and the optimal parameters modelled in the Cadence environment. A cross-coupled circuit with level shifter loop is also proposed to improve the overall step up voltage output and hybrid converter increases the start-up speed by 23.5%. The proposed system is implemented in a standard 0.18-μm CMOS technology. Simulation results show that the 4-phase start-up and cross coupled with level-shifter can achieve a maximum efficiency of 60%

Energy-Efficient Start-up Power Management for Batteryless Biomedical Implant Devices

This paper presents a solar energy harvesting power management using the high-efficiency switched capacitor DC-DC converter for biomedical implant applications. By employing an on-chip start-up circuit with parallel connected Photovoltaic (PV) cells, a small efficiency improvement can be obtained when compared with the traditional stacked photodiode methodology to boost the harvested voltage while preserving a single-chip solution. The PV cells have been optimised in the PC1D software and the optimal parameters modelled in the Cadence environment. A cross-coupled circuit with level shifter loop is also proposed to improve the overall step up voltage output and hybrid converter increases the start-up speed by 23.5%. The proposed system is implemented in a standard 0.18-μm CMOS technology. Simulation results show that the 4-phase start-up and cross coupled with level-shifter can achieve a maximum efficiency of 60%

Power management using photovoltaic cells for implantable devices

This paper presents a novel inductor-less switched capacitor (SC) DC-DC converter, which generates simultaneous dual-output voltages for implantable electronic devices. Present dual output converters are limited to fixed ratio gain, which degrade conversion efficiency when the input voltage changes. The proposed power converter offers both step-up and step-down conversion with 4-phase reconfigurable logic. With an input voltage of 1 V provided by photovoltaic (PV) cells, the proposed converter achieves step-up, step-down and synchronised voltage conversions in four gain modes. These are 1.5 V and 0.5 V for Normal mode, 2 V and 1 V for High mode, 2 V for Double Boost mode, as well as 3 V and 2 V for Super Boost mode with the ripple variation of 14-59 mV. The converter circuit has been simulated in standard 0.18 μm CMOS technology and the results agree with state-of-the-art SC converters. However, our proposed monolithically integrated PV powered circuit achieves a conversion efficiency of 85.26% and provides extra flexibility in terms of gain, which is advantageous for future implantable applications that have a range of inputs. This research is therefore an important step in achieving truly autonomous implantable electronic devices

Analysis and design of switched-capacitor DC-DC converters with discrete event models

Ph. D. Thesis.Switched-capacitor DC-DC converters (SCDDCs) play a critical role in low power integrated systems. The analysis and design processes of an SCDDC impact the performance and power efficiency of the whole system. Conventionally, researchers carry out the analysis and design processes by viewing SCDDCs as analogue circuits. Analogue attributes of an SCDDC, such as the charge flow current or the equivalent output impedance, have been studied in considerable detail for performance enhancement. However, in most existing work, less attention is paid to the analysis of discrete events (e.g. digital signal transitions) and the relationships between discrete events in SCDDCs. These discrete events and the relationships between discrete events also affect the performance of SCDDCs. Certain negative effects of SCDDCs such as leakage current are introduced by unhealthy discrete states. For example, MOS devices in an SCDDC could conduct undesirably under certain combinations of signals, resulting in reversion losses (a type of leakage in SCDDCs). However, existing work only use verbal reasoning and waveform descriptions when studying these discrete events, which may cause confusion and result in an informal design process consisting of intuitive design and backed up merely by validation based on natural language discussions and simulations. There is therefore a need for formalised methods to describe and analyse these discrete events which may facilitate systematic design techniques. This thesis presents a new method of analysing and designing SCDDCs using discrete event models. Discrete event models such as Petri nets and Signal Transition Graphs (STGs) are commonly used in asynchronous circuits to formally describe and analyse the relationships between discrete transitions. Modelling SCDDCs with discrete event models provides a formal way to describe the relations between discrete transitions in SCDDCs. These discrete event models can be used for analysis, verification and even design guidance for SCDDC design. The rich set of existing analysis methods and tools for discrete event models could be applied to SCDDCs, potentially improving the analysis and design flow for them. Moreover, since Petri nets and STGs are generally used to analyse and design asynchronous circuits, modelling and designing SCDDCs with STG models may additionally facilitate the incorporation of positive features of asynchronous circuits in SCDDCs (e.g. no clock skew). In this thesis, the relations between discrete events in SCDDCs are formally described with SC-STG (an extended STG targeting multi-voltage systems, to which SCDDCs belong), which avoids the potential confusion due to natural language and waveform descriptions. Then the concurrency and causality relations described in SC-STG model are extended to Petri nets, with which the presence of reversion losses can be formally determined and verified. Finally, based on the STG and Petri net models, a new design method for reversion-loss-free SCDDCs is proposed. In SCDDCs designed with the new method, reversion losses are entirely removed by introducing asynchronous controls, synthesised with the help of a software synthesis toolkit “Workcraft”. To demonstrate the analysis capabilities of the method, several cross-coupled voltage doublers (a type of SCDDC) are analysed and studied with discrete event models as examples in this thesis. To demonstrate the design capabilities of the method, a new reversion-loss-free cross-coupled voltage doubler is designed. The cross-coupled voltage doubler is widely used in low power integrated systems such as flash memories, LCD drivers and wireless energy harvesting systems. The proposed modelling method is potentially used in both research and industrial area of those applications for a formal and high-efficiency design proces

차량용 CIS Interface 를 위한 All-Digital Phase-Locked Loop 의 설계 및 분석

학위논문 (석사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2021. 2. 정덕균.This thesis presents design techniques for All-Digital Phase-Locked Loop (ADPLL) assisting the automotive CMOS image sensor (CIS) interface. To target Gear 3 of the automotive physical system, the proposed AD-PLL has a wide operation range, low RMS jitter, and high PVT tolerance characteristics. Detailed analysis of the loop dynamics and the noise analysis of AD-PLL are done by using Matlab and Verilog behavioral modeling simulation before an actual design. Based on that analysis, the optimal DLF gain configurations are yielded, and also, accurate output responses and performance are predictable. The design techniques to reduce the output RMS jitter are discussed thoroughly and utilized for actual implementation. The proposed AD-PLL is fabricated in the 40 nm CMOS process and occupies an effective area of 0.026 mm2. The PLL output clock pulses exhibit an RMS jitter of 827 fs at 2 GHz. The power dissipation is 5.8 mW at 2 GHz, where the overall supply voltage domain is 0.9 V excluding the buffer which is 1.1 V domain.본 논문에서는 자동차 CMOS 이미지 센서 (CIS) 인터페이스를 지원하 는 AD-PLL 을 제안한다. Automotive Physical 시스템의 Gear 3 를 지원하기 위해 제안된 AD-PLL 은 1.5 GHz 에서 3 GHz 의 동작 주파수를 가지며, 낮 은 RMS Jitter 및 PVT 변화에 대한 높은 둔감성을 갖는다. 설계에 앞서서 Matlab 및 Verilog Behavioral Simulation 을 통해 Loop system 의 역학에 대한 자세한 분석 및 AD-PLL 의 Noise 분석을 수행하였고, 이 분석을 기반으로 최적의 DLF gain 과 정확한 출력 응답 및 성능을 예측 할 수 있었다. 또한, 출력의 Phase Noise 와 RMS Jitter 를 줄이기 위한 설계 기법을 자세히 다루고 있으며 이를 실제 구현에 활용했다. 제안된 회로는 40 nm CMOS 공정으로 제작되었으며 Decoupling Cap 을 제외하고 0.026 mm2 의 유효 면적을 차지한다. 측정된 출력 Clock 신호의 RMS Jitter 값은 2 GHz 에서 827 fs 이며, 총 5.8 mW의 Power 를 소비한다. 이 때, 전체적인 공급 전압은 0.9 V 이며, Buffer 의 Power 만이 1.1 V 를 사용하 였다.ABSTRACT I CONTENTS II LIST OF FIGURES IV LIST OF TABLES VII CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 3 CHAPTER 2 BACKGROUND ON ALL-DIGITAL PLL 4 2.1 OVERVIEW 4 2.2 BUILDING BLOCKS OF AD-PLL 7 2.2.1 TIME-TO-DIGITAL CONVERTER 7 2.2.2 DIGITALLY-CONTROLLED OSCILLATOR 10 2.2.3 DIGITAL LOOP FILTER 13 2.2.4 DELTA-SIGMA MODULATOR 16 2.3 PHASE NOISE ANALYSIS OF AD-PLL 20 2.3.1 BASIC ASSUMPTION OF LINEAR ANALYSIS 20 2.3.2 NOISE SOURCES OF AD-PLL 21 2.3.3 EFFECTS OF LOOP DELAY ON AD-PLL 24 2.3.4 PHASE NOISE ANALYSIS OF PROPOSED AD-PLL 26 CHAPTER 3 DESIGN OF ALL-DIGITAL PLL 28 3.1 DESIGN CONSIDERATION 28 3.2 OVERALL ARCHITECTURE 30 3.3 CIRCUIT IMPLEMENTATION 32 3.3.1 PFD-TDC 32 3.3.2 DCO 37 3.3.3 DIGITAL BLOCK 43 3.3.4 LEVEL SHIFTING BUFFER AND DIVIDER 45 CHAPTER 4 MEASUREMENT AND SIMULATION RESULTS 52 4.1 DIE PHOTOMICROGRAPH 52 4.2 MEASUREMENT SETUP 54 4.3 TRANSIENT ANALYSIS 57 4.4 PHASE NOISE AND SPUR PERFORMANCE 59 4.4.1 FREE-RUNNING DCO 59 4.4.2 PLL PERFORMANCE 61 4.5 PERFORMANCE SUMMARY 65 CHAPTER 5 CONCLUSION 67 BIBLIOGRAPHY 68 초 록 72Maste

Power management systems based on switched-capacitor DC-DC converter for low-power wearable applications

The highly efficient ultra-low-power management unit is essential in powering low-power wearable electronics. Such devices are powered by a single input source, either by a battery or with the help of a renewable energy source. Thus, there is a demand for an energy conversion unit, in this case, a DC-DC converter, which can perform either step-up or step-down conversions to provide the required voltage at the load. Energy scavenging with a boost converter is an intriguing choice since it removes the necessity of bulky batteries and considerably extends the battery life. Wearable devices are typically powered by a monolithic battery. The commonly available battery such as Alkaline or Lithium-ion, degrade over time due to their life spans as it is limited by the number of charge cycles- which depend highly on the environmental and loading condition. Thus, once it reaches the maximum number of life cycles, the battery needs to be replaced. The operation of the wearable devices is limited by usable duration, which depends on the energy density of the battery. Once the stored energy is depleted, the operation of wearable devices is also affected, and hence it needs to be recharged. The energy harvesters- which gather the available energy from the surroundings, however, have no limitation on operating life. The application can become battery-less given that harvestable energy is sufficiently powering the low-power devices. Although the energy harvester may not completely replace the battery source, it ensures the maximum duration of use and assists to become autonomous and self-sustain devices. The photovoltaic (PV) cell is a promising candidate as a hypothetical input supply source among the energy harvesters due to its smaller area and high power density over other harvesters. Solar energy use PV harvester can convert ambient light energy into electrical energy and keep it in the storage device. The harvested output of PV cannot directly connect to wearable loads for two main reasons. Depending on the incoming light, the harvested current result in varying open-circuit voltage. It requires the power management circuit to deal with unregulated input variation. Second, depending on the PV cell's material type and an effective area, the I-V characteristic's performance varies, resulting in a variation of the output power. There are several works of maximum power point tracking (MPPT) methods that allow the solar energy harvester to achieve optimal harvested power. Therefore, the harvested power depends on the size and usually small area cell is sufficient for micro-watt loads low-powered applications. The available harvested voltage, however, is generally very low-voltage range between 0.4-0.6 V. The voltage ratings of electronics in standard wearable applications operate in 1.8-3 V voltages as described in introduction’s application example section. It is higher than the supply source can offer. The overcome the mismatch voltage between source and supply circuit, a DC-DC boost converter is necessary. The switch-mode converters are favoured over the linear converters due to their highly efficient and small area overhead. The inductive converter in the switch-mode converter is common due to its high-efficiency performance. However, the integration of the inductor in the miniaturised integrated on-chip design tends to be bulky. Therefore, the switched-capacitor approach DC-DC converters will be explored in this research. In the switched-capacitor converter universe, there is plenty of work for single-output designs for various topologies. Most converters are reconfigurable to the different DC voltage levels apart from Dickson and cross-coupled charge pump topologies due to their boosting power stage architecture through a number of stages. However, existing multi-output converters are limited to the fixed gain ratio. This work explores the reconfigurable dual-output converter with adjustable gain to compromise the research gap. The thesis's primary focus is to present the inductor-less, switched-capacitor-based DC-DC converter power management system (PMS) supplied by a varying input of PV energy harvester input source. The PMS should deliver highly efficient regulated voltage conversion ratio (VCR) outputs to low-power wearable electronic devices that constitute multi-function building blocks

Development of electronics for microultrasound capsule endoscopy

Development of intracorporeal devices has surged in the last decade due to advancements in the semiconductor industry, energy storage and low-power sensing systems. This work aims to present a thorough systematic overview and exploration of the microultrasound (µUS) capsule endoscopy (CE) field as the development of electronic components will be key to a successful applicable µUSCE device. The research focused on investigating and designing high-voltage (HV, < 36 V) generating and driving circuits as well as a low-noise amplifier (LNA) for battery-powered and volume-limited systems. In implantable applications, HV generation with maximum efficiency is required to improve the operational lifetime whilst reducing the cost of the device. A fully integrated hybrid (H) charge pump (CP) comprising a serial-parallel (SP) stage was designed and manufactured for > 20 V and 0 - 100 µA output capabilities. The results were compared to a Dickson (DKCP) occupying the same chip area; further improvements in the SPCP topology were explored and a new switching scheme for SPCPs was introduced. A second regulated CP version was excogitated and manufactured to use with an integrated µUS pulse generator. The CP was manufactured and tested at different output currents and capacitive loads; its operation with an US pulser was evaluated and a novel self-oscillating CP mechanism to eliminate the need of an auxiliary clock generator with a minimum area overhead was devised. A single-output universal US pulser was designed, manufactured and tested with 1.5 MHz, 3 MHz, and 28 MHz arrays to achieve a means of fully-integrated, low-power transducer driving. The circuit was evaluated for power consumption and pulse generation capabilities with different loads. Pulse-echo measurements were carried out and compared with those from a commercial US research system to characterise and understand the quality of the generated pulse. A second pulser version for a 28 MHz array was derived to allow control of individual elements. The work involved its optimisation methodology and design of a novel HV feedback-based level-shifter. A low-noise amplifier (LNA) was designed for a wide bandwidth µUS array with a centre frequency of 28 MHz. The LNA was based on an energy-efficient inverter architecture. The circuit encompassed a full power-down functionality and was investigated for a self-biased operation to achieve lower chip area. The explored concepts enable realisation of low power and high performance LNAs for µUS frequencies