AN O-TREE FOR FLOORPLAN

ABSTRACT: Floorplanning is the process to arranging the number of blocks in to boundary. Conventionally different trees are used for Floorplanning. Here a new representation called O-Tree is used. This O-tree is the representation of admissible placement and used for Floorplanning. The admissible placement is to move blocks either left or bottom of the boundary and it reduces the white spaces in the Floorplanning. A deterministic algorithm will propose for the Floorplanning. This algorithm is generating from the O-Tree representation. The effectiveness of the proposed algorithm will be tested in MCNC benchmark suites

The Design of a single chip 8x8 ATM switch in 0.5 micrometers CMOS VLSI

This thesis illustrates the design of a single chip Asynchronous Transfer Mode (ATM) protocol switch using Very Large Scale Integration (VLSI). The ATM protocol is the data communications protocol used in the implementation of the Broadband Integrated Services Digital Network (B-ISDN), A number of switch architecture are first studied and a new architecture is developed based on optimizing performance and practicality of implementation in VLSI. A fully interconnected switch architecture is implemented by permanently connecting every input port to all the output ports. An output buffering scheme is used to handle cells that cannot be routed right away. This new architecture is caned the High Performance (HiPer) Switch Architecture. The performance of the architecture is simulated using a C++ model. Simulation results for a randomly distributed traffic pattern with a 90% probability of cells arriving in a time slot produces a Cell Loss Ratio of 1.Ox 10^-8 with output buffers that can hold 64 cells. The device is then modeled in VHDL to verify its functionality. Finally the layout of an 8x8 switch is produced using a 0.5 micrometer CMOS VLSI process and simulations of that circuit show that a peak throughput of 200 Mbps per output port can be achieve

Bandwidth optimization in asynchronous NoCs by customizing link wire length

Journal ArticleThe bandwidth requirement for each link on a network-on-chip (NoC) may differ based on topology and traffic properties of the IP cores. Available bandwidth on an asynchronous NoC link will also vary depending on the wire length between sender and receiver. We explore the benefit to NoC performance when this property is used to increase bandwidth on specific links that carry the most traffic of an SoC design. Two methods are used to accomplish this: specifying router locations on the floorplan, and adding pipeline latches on long links. Energy and latency characteristics of an asynchronous NoC are compared to a similarly-designed synchronous NoC. The results indicate that the asynchronous network has lower energy, and link-specific bandwidth optimization has improved the average packet latency. Adding pipeline latches to congested links yields the most improvement. This link-specific optimization is applicable not only to the router and network we present here, but any asynchronous NoC used in a eterogeneous SoC

Application-Specific Heterogeneous Network-on-Chip Design

Cataloged from PDF version of article.As a result of increasing communication demands, application-specific and scalable Network-on-Chips (NoCs) have emerged to connect processing cores and subsystems in Multiprocessor System-on-Chips. A challenge in application-specific NoC design is to find the right balance among different tradeoffs, such as communication latency, power consumption and chip area. We propose a novel approach that generates latency-aware heterogeneous NoC topology. Experimental results show that our approach improves the total communication latency up to 27% with modest power consumption. © 2013 The Author 2013. Published by Oxford University Press on behalf of The British Computer Society

B*tree representation based thermal and variability aware floorplanning frame work

Master'sMASTER OF ENGINEERIN

The implementation and applications of multiple-valued logic

Multiple-Valued Logic (MVL) takes two major forms. Multiple-valued circuits can implement the logic directly by using multiple-valued signals, or the logic can be implemented indirectly with binary circuits, by using more than one binary signal to represent a single multiple-valued signal. Techniques such as carry-save addition can be viewed as indirectly implemented MVL. Both direct and indirect techniques have been shown in the past to provide advantages over conventional arithmetic and logic techniques in algorithms required widely in computing for applications such as image and signal processing. It is possible to implement basic MVL building blocks at the transistor level. However, these circuits are difficult to design due to their non binary nature. In the design stage they are more like analogue circuits than binary circuits. Current integrated circuit technologies are biased towards binary circuitry. However, in spite of this, there is potential for power and area savings from MVL circuits, especially in technologies such as BiCMOS. This thesis shows that the use of voltage mode MVL will, in general not provide bandwidth increases on circuit buses because the buses become slower as the number of signal levels increases. Current mode MVL circuits however do have potential to reduce power and area requirements of arithmetic circuitry. The design of transistor level circuits is investigated in terms of a modern production technology. A novel methodology for the design of current mode MVL circuits is developed. The methodology is based upon the novel concept of the use of non-linear current encoding of signals, providing the opportunity for the efficient design of many previously unimplemented circuits in current mode MVL. This methodology is used to design a useful set of basic MVL building blocks, and fabrication results are reported. The creation of libraries of MVL circuits is also discussed. The CORDIC algorithm for two dimensional vector rotation is examined in detail as an example for indirect MVL implementation. The algorithm is extended to a set of three dimensional vector rotators using conventional arithmetic, redundant radix four arithmetic, and Taylor's series expansions. These algorithms can be used for two dimensional vector rotations in which no scale factor corrections are needed. The new algorithms are compared in terms of basic VLSI criteria against previously reported algorithms. A pipelined version of the redundant arithmetic algorithm is floorplanned and partially laid out to give indications of wiring overheads, and layout densities. An indirectly implemented MVL algorithm such as the CORDIC algorithm described in this thesis would clearly benefit from direct implementation in MVL