16-bit Digital Adder Design in 250nm and 64-bit Digital Comparator Design in 90nm CMOS Technologies

High speed, low power, and area efficient adders and comparators continue to play a key role in hardware implementation of digital signal processing applications. Adders based on Complimentary Pass Transistor Logic (CPL) are power and area efficient, but are slower compared to Square Root Carry Select (SQRT-CS) based adders. This thesis demonstrates a unique custom designed 16-bit adder in 250-nm CMOS technology to obtain fast and power/area efficient features by combining CPL and CS logic. Comparing the results obtained for proposed 16-bit Linear CPL/CS adder with the BEC (Binary Excess-1 Code) based low power SQRT-CS adder, the delay is reduced by approximately one thirds, power is reduced by 19.2%, and the number of transistors is reduced by 23.4%. Also, new tree-based 64-bit static and dynamic digital comparators are presented in this thesis to perform high speed and low power operations. This tree-based architecture combines a new approach of designing dynamic comparator using a low duty cycle clock to reduce the short circuit power consumption in pre-charge (or pre-discharge) mode. This work also introduces a new sizing strategy and load balancing techniques to improve self-pipelining tendency of a tree based design. A resource sharing technique is also integrated in both static and dynamic comparator designs. At 1.2V power supply in CMOS 90nm technology, worst path delay and worst power are 374ps and 822µW, respectively for low cost static design with 1244 (768+476) transistors in total. 768 transistors are used for resource sharing. The proposed full and partially dynamic designs show superior power efficiency compared to recent state of art designs. The worst power consumptions at 5GHz and 25% (50ps) duty cycle clock for the 64-bit full and partially dynamic comparator designs are 5.00mW and 2.78mW, respectively. 769 (320+449) transistors includes 320 transistors for resource sharing, and 1217 (768+449) includes 768 transistors for resource sharing for full and partial dynamic comparators, respectively

A RISC-V Vector Processor With Simultaneous-Switching Switched-Capacitor DC-DC Converters in 28 nm FDSOI

This work demonstrates a RISC-V vector microprocessor implemented in 28 nm FDSOI with fully integrated simultaneous-switching switched-capacitor DC-DC (SC DC-DC) converters and adaptive clocking that generates four on-chip voltages between 0.45 and 1 V using only 1.0 V core and 1.8 V IO voltage inputs. The converters achieve high efficiency at the system level by switching simultaneously to avoid charge-sharing losses and by using an adaptive clock to maximize performance for the resulting voltage ripple. Details about the implementation of the DC-DC switches, DC-DC controller, and adaptive clock are provided, and the sources of conversion loss are analyzed based on measured results. This system pushes the capabilities of dynamic voltage scaling by enabling fast transitions (20 ns), simple packaging (no off-chip passives), low area overhead (16%), high conversion efficiency (80%-86%), and high energy efficiency (26.2 DP GFLOPS/W) for mobile devices

Fine-grained parallelization of fitness functions in bioinformatics optimization problems: gene selection for cancer classification and biclustering of gene expression data

ANTECEDENTES: las metaheurísticas se utilizan ampliamente para resolver grandes problemas de optimización combinatoria en bioinformática debido al enorme conjunto de posibles soluciones. Dos problemas representativos son la selección de genes para la clasificación del cáncer y el agrupamiento de los datos de expresión génica. En la mayoría de los casos, estas metaheurísticas, así como otras técnicas no lineales, aplican una función de adecuación a cada solución posible con una población de tamaño limitado, y ese paso involucra latencias más altas que otras partes de los algoritmos, lo cual es la razón por la cual el tiempo de ejecución de las aplicaciones dependerá principalmente del tiempo de ejecución de la función de aptitud. Además, es habitual encontrar formulaciones aritméticas de punto flotante para las funciones de fitness. De esta manera, una paralelización cuidadosa de estas funciones utilizando la tecnología de hardware reconfigurable acelerará el cálculo, especialmente si se aplican en paralelo a varias soluciones de la población. RESULTADOS: una paralelización de grano fino de dos funciones de aptitud de punto flotante de diferentes complejidades y características involucradas en el biclustering de los datos de expresión génica y la selección de genes para la clasificación del cáncer permitió obtener mayores aceleraciones y cómputos de potencia reducida con respecto a los microprocesadores habituales. CONCLUSIONES: Los resultados muestran mejores rendimientos utilizando tecnología de hardware reconfigurable en lugar de los microprocesadores habituales, en términos de tiempo de consumo y consumo de energía, no solo debido a la paralelización de las operaciones aritméticas, sino también gracias a la evaluación de aptitud concurrente para varios individuos de la población en La metaheurística. Esta es una buena base para crear soluciones aceleradas y de bajo consumo de energía para escenarios informáticos intensivos.BACKGROUND: Metaheuristics are widely used to solve large combinatorial optimization problems in bioinformatics because of the huge set of possible solutions. Two representative problems are gene selection for cancer classification and biclustering of gene expression data. In most cases, these metaheuristics, as well as other non-linear techniques, apply a fitness function to each possible solution with a size-limited population, and that step involves higher latencies than other parts of the algorithms, which is the reason why the execution time of the applications will mainly depend on the execution time of the fitness function. In addition, it is usual to find floating-point arithmetic formulations for the fitness functions. This way, a careful parallelization of these functions using the reconfigurable hardware technology will accelerate the computation, specially if they are applied in parallel to several solutions of the population. RESULTS: A fine-grained parallelization of two floating-point fitness functions of different complexities and features involved in biclustering of gene expression data and gene selection for cancer classification allowed for obtaining higher speedups and power-reduced computation with regard to usual microprocessors. CONCLUSIONS: The results show better performances using reconfigurable hardware technology instead of usual microprocessors, in computing time and power consumption terms, not only because of the parallelization of the arithmetic operations, but also thanks to the concurrent fitness evaluation for several individuals of the population in the metaheuristic. This is a good basis for building accelerated and low-energy solutions for intensive computing scenarios.• Ministerio de Economía y Competitividad y Fondos FEDER. Contrato TIN2012-30685 (I+D+i) • Gobierno de Extremadura. Ayuda GR15011 para grupos TIC015 • CONICYT/FONDECYT/REGULAR/1160455. Beca para Ricardo Soto Guzmán • CONICYT/FONDECYT/REGULAR/1140897. Beca para Broderick CrawfordpeerReviewe

Baseband analog front-end and digital back-end for reconfigurable multi-standard terminals

Multimedia applications are driving wireless network operators to add high-speed data services such as Edge (E-GPRS), WCDMA (UMTS) and WLAN (IEEE 802.11a,b,g) to the existing GSM network. This creates the need for multi-mode cellular handsets that support a wide range of communication standards, each with a different RF frequency, signal bandwidth, modulation scheme etc. This in turn generates several design challenges for the analog and digital building blocks of the physical layer. In addition to the above-mentioned protocols, mobile devices often include Bluetooth, GPS, FM-radio and TV services that can work concurrently with data and voice communication. Multi-mode, multi-band, and multi-standard mobile terminals must satisfy all these different requirements. Sharing and/or switching transceiver building blocks in these handsets is mandatory in order to extend battery life and/or reduce cost. Only adaptive circuits that are able to reconfigure themselves within the handover time can meet the design requirements of a single receiver or transmitter covering all the different standards while ensuring seamless inter-interoperability. This paper presents analog and digital base-band circuits that are able to support GSM (with Edge), WCDMA (UMTS), WLAN and Bluetooth using reconfigurable building blocks. The blocks can trade off power consumption for performance on the fly, depending on the standard to be supported and the required QoS (Quality of Service) leve

Integrated temperature sensors in deep sub-micron CMOS technologies

textIntegrated temperature sensors play an important role in enhancing the performance of on-chip power and thermal management systems in today's highly-integrated system-on-chip (SoC) platforms, such as microprocessors. Accurate on-chip temperature measurement is essential to maximize the performance and reliability of these SoCs. However, due to non-uniform power consumption by different functional blocks, microprocessors have fairly large thermal gradient (and variation) across their chips. In the case of multi-core microprocessors for example, there are task-specific thermal gradients across different cores on the same die. As a result, multiple temperature sensors are needed to measure the temperature profile at all relevant coordinates of the chip. Subsequently, the results of the temperature measurements are used to take corrective measures to enhance the performance, or save the SoC from catastrophic over-heating situations which can cause permanent damage. Furthermore, in a large multi-core microprocessor, it is also imperative to continuously monitor potential hot-spots that are prone to thermal runaway. The locations of such hot spots depend on the operations and instruction the processor carries out at a given time. Due to practical limitations, it is an overkill to place a big size temperature sensor nearest to all possible hot spots. Thus, an ideal on-chip temperature sensor should have minimal area so that it can be placed non-invasively across the chip without drastically changing the chip floor plan. In addition, the power consumption of the sensors should be very low to reduce the power budget overhead of thermal monitoring system, and to minimize measurement inaccuracies due to self-heating. The objective of this research is to design an ultra-small size and ultra-low power temperature sensor such that it can be placed in the intimate proximity of all possible hot spots across the chip. The general idea is to use the leakage current of a reverse-bias p-n junction diode as an operand for temperature sensing. The tasks within this project are to examine the theoretical aspect of such sensors in both Silicon-On-Insulator (SOI), and bulk Complementary Metal-Oxide Semiconductor (CMOS) technologies, implement them in deep sub-micron technologies, and ultimately evaluate their performances, and compare them to existing solutions.Electrical and Computer Engineerin

Analyses and design strategies for fundamental enabling building blocks: Dynamic comparators, voltage references and on-die temperature sensors

Dynamic comparators and voltage references are among the most widely used fundamental building blocks for various types of circuits and systems, such as data converters, PLLs, switching regulators, memories, and CPUs. As thermal constraints quickly emerged as a dominant performance limiter, on-die temperature sensors will be critical to the reliable operation of future integrated circuits. This dissertation investigates characteristics of these three enabling circuits and design strategies for improving their performances. One of the most critical specifications of a dynamic comparator is its input referred offset voltage, which is pivotal to achieving overall system performance requirements of many mixed-signal circuits and systems. Unlike offset voltages in other circuits such as amplifiers, the offset voltage in a dynamic comparator is extremely challenging to analyze and predict analytically due to its dependence on transient response and due to internal positive feedback and time-varying operating points in the comparator. In this work, a novel balanced method is proposed to facilitate the evaluation of time-varying operating points of transistors in a dynamic comparator. Two types of offsets are studied in the model: (1) static offset voltage caused by mismatches in mobilities, transistor sizes, and threshold voltages, and (2) dynamic offset voltage caused by mismatches in parasitic capacitors or loading capacitors. To validate the proposed method, dynamic comparators in two prevalent topologies are implemented in 0.25 μm and 40 nm CMOS technologies. Agreement between predicted results and simulated results verifies the effectiveness of the proposed method. The new method and the analytical models enable designers to identify the most dominant contributors to offset and to optimize the dynamic comparators\u27 performances. As an illustrating example, the Lewis-Gray dynamic comparator was analyzed using the balanced method and redesigned to minimize its offset voltage. Simulation results show that the offset voltage was easily reduced by 41% while maintaining the same silicon area. A bandgap voltage reference is one of the core functional blocks in both analog and digital systems. Despite the reported improvements in performance of voltage references, little attention has been focused on theoretical characterizations of non-ideal effects on the value of the output voltage, on the inflection point location and on the curvature of the reference voltage. In this work, a systematic approach is proposed to analytically determine the effects of two non-ideal elements: the temperature dependent gain-determining resistors and the amplifier offset voltage. The effectiveness of the analytical models is validated by comparing analytical results against Spectre simulation results. Research on on-die temperature sensor design has received rapidly increasing attention since component and power density induced thermal stress has become a critical factor in the reliable operation of integrated circuits. For effective power and thermal management of future multi-core systems, hundreds of sensors with sufficient accuracy, small area and low power are required on a single chip. This work introduces a new family of highly linear on chip temperature sensors. The proposed family of temperature sensors expresses CMOS threshold voltage as an output. The sensor output is independent of power supply voltage and independent of mobility values. It can achieve very high temperature linearity, with maximum nonlinearity around +/- 0.05oC over a temperature range of -20oC to 100oC. A sizing strategy based on combined analytical analysis and numerical optimization has been presented. Following this method, three circuits A, B and C have been designed in standard 0.18 ym CMOS technology, all achieving excellent linearity as demonstrated by Cadence Spectre simulations. Circuits B and C are the modified versions of circuit A, and have improved performance at the worst corner-low voltage supply and high threshold voltage corner. Finally, a direct temperature-to-digital converter architecture is proposed as a master-slave hybrid temperature-to-digital converter. It does not require any traditional constant reference voltage or reference current, it does not attempt to make any node voltage or branch current constant or precisely linear to temperature, yet it generates a digital output code that is very linear with temperature

Merged Two-Stage Power Converter With Soft Charging Switched-Capacitor Stage in 180 nm CMOS

In this paper, we introduce a merged two-stage dc-dc power converter for low-voltage power delivery. By separating the transformation and regulation function of a dc-dc power converter into two stages, both large voltage transformation and high switching frequency can be achieved. We show how the switched-capacitor stage can operate under soft charging conditions by suitable control and integration (merging) of the two stages. This mode of operation enables improved efficiency and/or power density in the switched-capacitor stage. A 5-to-1 V, 0.8 W integrated dc-dc converter has been developed in 180 nm CMOS. The converter achieves a peak efficiency of 81%, with a regulation stage switching frequency of 10 MHz.Interconnect Focus Center (United States. Defense Advanced Research Projects Agency and Semiconductor Research Corporation