Wireless wire - ultra-low-power and high-data-rate wireless communication systems

With the rapid development of communication technologies, wireless personal-area communication systems gain momentum and become increasingly important. When the market gets gradually saturated and the technology becomes much more mature, new demands on higher throughput push the wireless communication further into the high-frequency and high-data-rate direction. For example, in the IEEE 802.15.3c standard, a 60-GHz physical layer is specified, which occupies the unlicensed 57 to 64 GHz band and supports gigabit links for applications such as wireless downloading and data streaming. Along with the progress, however, both wireless protocols and physical systems and devices start to become very complex. Due to the limited cut-off frequency of the technology and high parasitic and noise levels at high frequency bands, the power consumption of these systems, especially of the RF front-ends, increases significantly. The reason behind this is that RF performance does not scale with technology at the same rate as digital baseband circuits. Based on the challenges encountered, the wireless-wire system is proposed for the millimeter wave high-data-rate communication. In this system, beamsteering directional communication front-ends are used, which confine the RF power within a narrow beam and increase the level of the equivalent isotropic radiation power by a factor equal to the number of antenna elements. Since extra gain is obtained from the antenna beamsteering, less front-end gain is required, which will reduce the power consumption accordingly. Besides, the narrow beam also reduces the interference level to other nodes. In order to minimize the system average power consumption, an ultra-low power asynchronous duty-cycled wake-up receiver is added to listen to the channel and control the communication modes. The main receiver is switched on by the wake-up receiver only when the communication is identified while in other cases it will always be in sleep mode with virtually no power consumed. Before transmitting the payload, the event-triggered transmitter will send a wake-up beacon to the wake-up receiver. As long as the wake-up beacon is longer than one cycle of the wake-up receiver, it can be captured and identified. Furthermore, by adopting a frequency-sweeping injection locking oscillator, the wake-up receiver is able to achieve good sensitivity, low latency and wide bandwidth simultaneously. In this way, high-data-rate communication can be achieved with ultra-low average power consumption. System power optimization is achieved by optimizing the antenna number, data rate, modulation scheme, transceiver architecture, and transceiver circuitries with regards to particular application scenarios. Cross-layer power optimization is performed as well. In order to verify the most critical elements of this new approach, a W-band injection-locked oscillator and the wake-up receiver have been designed and implemented in standard TSMC 65-nm CMOS technology. It can be seen from the measurement results that the wake-up receiver is able to achieve about -60 dBm sensitivity, 10 mW peak power consumption and 8.5 µs worst-case latency simultaneously. When applying a duty-cycling scheme, the average power of the wake-up receiver becomes lower than 10 µW if the event frequency is 1000 times/day, which matches battery-based or energy harvesting-based wireless applications. A 4-path phased-array main receiver is simulated working with 1 Gbps data rate and on-off-keying modulation. The average power consumption is 10 µW with 10 Gb communication data per day

Design and Implementation of a Low‐Power Wireless Respiration Monitoring Sensor

Wireless devices for monitoring of respiration activities can play a major role in advancing modern home-based health care applications. Existing methods for respiration monitoring require special algorithms and high precision filters to eliminate noise and other motion artifacts. These necessitate additional power consuming circuitry for further signal conditioning. This dissertation is particularly focused on a novel approach of respiration monitoring based on a PVDF-based pyroelectric transducer. Low-power, low-noise, and fully integrated charge amplifiers are designed to serve as the front-end amplifier of the sensor to efficiently convert the charge generated by the transducer into a proportional voltage signal. To transmit the respiration data wirelessly, a lowpower transmitter design is crucial. This energy constraint motivates the exploration of the design of a duty-cycled transmitter, where the radio is designed to be turned off most of the time and turned on only for a short duration of time. Due to its inherent duty-cycled nature, impulse radio ultra-wideband (IR-UWB) transmitter is an ideal candidate for the implementation of a duty-cycled radio. To achieve better energy efficiency and longer battery lifetime a low-power low-complexity OOK (on-off keying) based impulse radio ultra-wideband (IR-UWB) transmitter is designed and implemented using standard CMOS process. Initial simulation and test results exhibit a promising advancement towards the development of an energy-efficient wireless sensor for monitoring of respiration activities

Power-efficient Circuit Architectures for Receivers Leveraging Nanoscale CMOS

Cellular and mobile communication markets, together with CMOS technology scaling, have made complex systems-on-chip integrated circuits (ICs) ubiquitous. Moving towards the internet of things that aims to extend this further requires ultra-low power and efficient radio communication that continues to take advantage of nanoscale CMOS processes. At the heart of this lie orthogonal challenges in both system and circuit architectures of current day technology. By enabling transceivers at center frequencies ranging in several tens of GHz, modern CMOS processes support bandwidths of up to several GHz. However, conventional narrowband architectures cannot directly translate or trade-off these speeds to lower power consumption. Pulse-radio UWB (PR-UWB), a fundamentally different system of communication enables this trade-off by bit-level duty-cycling i.e., power-gating and has emerged as an alternative to conventional narrowband systems to achieve better energy efficiency. However, system-level challenges in the implementation of transceiver synchronization and duty-cycling have remained an open challenge to realize the ultra-low power numbers that PR-UWB promises. Orthogonally, as CMOS scaling continues, approaching 28nm and 14nm in production digital processes, the key transistor characteristics have rapidly changed. Changes in supply voltage, intrinsic gain and switching speeds have rendered conventional analog circuit design techniques obsolete, since they do not scale well with the digital backend engines that dictate scaling. Consequently, circuit architectures that employ time-domain processing and leverage the faster switching speeds have become attractive. However, they are fundamentally limited by their inability to support linear domain-to-domain conversion and hence, have remained un-suited to high-performance applications. Addressing these requirements in different dimensions, two pulse-radio UWB receiver and a continuous-time filter silicon prototypes are presented in this work. The receiver prototypes focus on system level innovation while the filter serves as a demonstration vehicle for novel circuit architectures developed in this work. The PR-UWB receiver prototypes are implemented in a 65nm LP CMOS technology and are fully integrated solutions. The first receiver prototype is a compact UWB receiver front end operating at 4.85GHz that is aggressively duty-cycled. It occupies an active area of only 0.4 mm², thanks to the use of few inductors and RF G_m-C filters and incorporates an automatic-threshold-recovery-based demodulator for digitization. The prototype achieves a sensitivity of -88dBm at a data rate of 1Mbps (for a BER of 10^-3), while achieving the lowest energy consumption gradient (dP/df_data=450pJ/bit) amongst other receivers operating in the lower UWB band, for the same sensitivity. However, this prototype is limited by idle-time power consumption (e.g., bias) and lacks synchronization capability. A fully self-duty-cycled and synchronized UWB pulse-radio receiver SoC targeted at low-data-rate communication is presented as the second prototype. The proposed architecture builds on the automatic-threshold-recovery-based demodulator to achieve synchronization using an all-digital clock and data recovery loop. The SoC synchronizes with the incoming pulse stream from the transmitter and duty-cycles itself. The SoC prototype achieves a -79.5dBm, 1Mbps-normalized sensitivity for a >5X improvement over the state of the art in power consumption (375pJ/bit), thanks to aggressive signal path and bias circuit duty-cycling. The SoC is fully integrated to achieve RF-in to bit-out operation and can interface with off-chip, low speed digital components. Finally, switched-mode signal processing, a signal processing paradigm that enables the design of highly linear, power-efficient feedback amplifiers is presented. A 0.6V continuous-time filter prototype that demonstrates the advantages of this technique is presented in a 65nm GP CMOS process. The filter draws 26.2mW from the supply while operating at a full-scale that is 73% of the V_dd, a bandwidth of 70MHz and a peak signal-to-noise-and-distortion ratio (SNDR) of 55.8dB. This represents a 2-fold improvement in full-scale and a 10-fold improvement in the bandwidth over state-of-the-art filter implementations, while demonstrating excellent linearity and signal-to-noise ratio. To sum up, innovations spanning both system and circuit architectures that leverage the speeds of nanoscale CMOS processes to enable power-efficient solutions to next-generation wireless receivers are presented in this work

Ultra-Wideband Transceiver Design And Optimization

University of Minnesota Ph.D. dissertation. July 2015. Major: Electrical Engineering. Advisor: Ramesh Harjani. 1 computer file (PDF); xiii, 128 pages.The technology landscape has quickly changed over the last few years. Developments in personal area networks, IC technology, DSP processing and bio-medical devices have enabled the integration of short range communication into low cost personal health care solutions. Newer technologies and solutions are being developed to cater to the personal operating space(POS) and body area networks(BAN). Health care is driving towards using multiple sensor and therapeutic nodes inside the POS. Technology has enabled remote patient care where the patient has low cost on-body wearables that allow the patient/physician to access vital signs without the patient physically visiting the clinic. Big semiconductor giants want to move into the wearable health monitor space. Along with the developments in fitness based health wearables, there has been a lot of interest towards developing BAN devices catering to the 'mission-critical' wearables and implants. Hearing aids, EKG monitors, neurostimulators are some examples. This work explores the use of the 802.15 ulta wideband (UWB) standard for designing a radio to operate in the a wireless sensor network in the BAN. The specific application targeted is a hearing aid. However, the design in this work is capable of working in a low power low range application with the ability to have multiple data rates ranging from a few kHz to 10's of MHz. The first radio designed by Marconi using spark-gap transmitters was an impulse radio (IR). The IR UWB technology boasts of low power, low cost, high data rates, multiple channels, simultaneous networking, the ability to carry information through obstacles that more limited bandwidths cannot, and also potentially lower complexity hardware design. The inherent timing accuracy associated with the technology gives UWB transmissions immunity to multipath fading and are hence make them more suitable for a cluttered indoor environment. The key difference with the traditional narrowband transceiver is that instead of using continuous wave (CW) transmission, impulses in time are used. The timing accuracy associated with these impulses require synchronization in time, rather than synchronization in frequency for carrier-based CW systems. A complete fully integrated system is presented in thesis. This work presents a low-power noncoherent IR UWB transceiver operating at 5GHz in 0.13um CMOS. A fully-digital transmitter generates a shaped output pulse of 1GHz 3-dB bandwidth. DLLs provide a PVT-tolerant time-step resolution of 1ns over the entire symbol period and regulate the pulse generator center frequency. The transmitter outputs -31dBm (0.88pJ/pulse at 1Mpulse/s) with a dynamic (energy) efficiency of 16pJ/pulse. The transmit out pulse is FCC part 15 compliant over process voltage and temperature (PVT) variations. The transmitter is semi-compliant with IEEE 802.15.6 and IEEE 802.15.4 standards and will become completely compliant with minor modifications. The receiver presented in this work is a non-coherent energy detect IR UWB receiver. The receiver has an on-chip transformer preceding the LNA, which is followed by a super-regenerative amplifier (SRA), envelope detector, sample-and-holds, and a bank of comparators. The design is SRA based energy-detection receiver. Measured results show a receiver efficiency of 0.32nJ/bit at 20.8Mb/s and operation with inputs as low as -70dBm. The SRA based energy-detection receiver utilizes early/late detection for a two-step baseband synchronization algorithm. An integrated solution to the issue of synchronization is also proposed. The system proposed is capable of synchronization and tracking control. The system in this work utilizes early/late detection for a two-step baseband synchronization algorithm. The algorithm is implemented in Matlab and the time to synchronization is observed to be between 250us to a few couple of ms. Measurements have also been made using the receiver and manually implementing the algorithm. This work addresses all aspects time synchronization in an IR transceiver. The initial mismatch is addressed by two methods. Beyond the initial synchronization, the system presented in this system is also capable of tracking. This would mean that once the transceiver has been synchronized, the timing generation would continue to track the phase and the frequency changes depending upon crystal drift over time or movement between the receiver and the transmitter. A test was also performed on the complete transceiver system with two radios talking to each other over a highly attenuated wired channel

A Sub-nW 2.4 GHz Transmitter for Low Data-Rate Sensing Applications

This paper presents the design of a narrowband transmitter and antenna system that achieves an average power consumption of 78 pW when operating at a duty-cycled data rate of 1 bps. Fabricated in a 0.18 μm CMOS process, the transmitter employs a direct-RF power oscillator topology where a loop antenna acts as a both a radiative and resonant element. The low-complexity single-stage architecture, in combination with aggressive power gating techniques and sizing optimizations, limited the standby power of the transmitter to only 39.7 pW at 0.8 V. Supporting both OOK and FSK modulations at 2.4 GHz, the transmitter consumed as low as 38 pJ/bit at an active-mode data rate of 5 Mbps. The loop antenna and integrated diodes were also used as part of a wireless power transfer receiver in order to kick-start the system power supply prior to energy harvesting operation.Semiconductor Research Corporation. Interconnect Focus CenterSemiconductor Research Corporation. C2S2 Focus CenterNational Institutes of Health (U.S.) (Grant K08 DC010419)National Institutes of Health (U.S.) (Grant T32 DC00038)Bertarelli Foundatio

Crystal-Less RF Communication Integrated Circuits for Wireless Sensor Networks.

The evolution of computing devices has changed daily life significantly over the past decades, and it is still advancing towards pervasive and ubiquitous networks. At each step, the volume shrinks by 2-3 orders of magnitude while the functionality and computing power remains constant or increases. Wireless sensor networks (WSN) are perceived as the next big step of computing technology for a variety of applications, including environmental sensing, health monitoring, un-obtrusive surveillance and invisible labeling. With thin-film micro-battery technology and CMOS scaling, we can now envision complete sensor nodes with cubic-mm form factors. As node volume reduces, external components like a crystal frequency reference, which does not scale with frequency or process, becomes one of the bottlenecks of realizing cubic-mm WSN node devices. This dissertation covers several aspects of the energy and integration challenges associated with cubic-mm WSN nodes without crystal references. Several new compact and low-power RF circuits for the synchronization and communication of WSN nodes are proposed and discussed. A 60GHz antenna-referenced frequency-locked loop (FLL) using an on-chip patch antenna as both the radiator and the frequency reference has been demonstrated for RF synchronization. The FLL, targeting communication of non-coherent energy detection systems, provides adequate frequency accuracy without crystal references. A 10GHz ultra-wideband (UWB) crystal-less transmitter with an on-chip monopole antenna has also been demonstrated. It operates over the supply voltage range of a micro-battery; generate tunable pulse durations and center frequencies, and lives on an on-chip local decoupling capacitor only. A 1MHz temperature-compensated relaxation oscillator is also proposed in the dissertation for baseband data synchronization. With the modified RC network of the conventional relaxation oscillator, the transfer function of the network has a transmission zero, introducing an additional degree-of-freedom for temperature compensation design. Finally, a 60GHz transmit/receive (T/R) switch-less antenna front-end using an on-chip patch antenna is presented, which has an in-band isolation inherited from the standing wave pattern without implementing a T/R switch. The research projects have explored the circuit design techniques and system integration for cubic-mm energy-constrained devices, achieving both long lifetimes and small volumes for WSN applications.PhDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/99763/1/kkhuang_1.pd

Ultra-Low-Power Uwb Impulse Radio Design: Architecture, Circuits, And Applications

Recent advances in home healthcare, environmental sensing, and low power computing have created a need for wireless communication at very low power for low data rate applications. Due to higher energy/bit requirements at lower data -rate, achieving power levels low enough to enable long battery lifetime (~10 years) or power-harvesting supplies have not been possible with traditional approaches. Dutycycled radios have often been proposed in literature as a solution for such applications due to their ability to shut off the static power consumption at low data rates. While earlier radio nodes for such systems have been proposed based on a type of sleepwake scheduling, such implementations are still power hungry due to large synchronization uncertainty (~1[MICRO SIGN]s). In this dissertation, we utilize impulsive signaling and a pulse-coupled oscillator (PCO) based synchronization scheme to facilitate a globally synchronized wireless network. We have modeled this network over a widely varying parameter space and found that it is capable of reducing system cost as well as providing scalability in wireless sensor networks. Based on this scheme, we implemented an FCC compliant, 3-5GHz, timemultiplexed, dual-band UWB impulse radio transceiver, measured to consume only 20[MICRO SIGN]W when the nodes are synchronized for peer-peer communication. At the system level the design was measured to consume 86[MICRO SIGN]W of power, while facilitating multi- hop communication. Simple pulse-shaping circuitry ensures spectral efficiency, FCC compliance and ~30dB band-isolation. Similarly, the band-switchable, ~2ns turn-on receiver implements a non-coherent pulse detection scheme that facilitates low power consumption with -87dBm sensitivity at 100Kbps. Once synchronized the nodes exchange information while duty-cycling, and can use any type of high level network protocols utilized in packet based communication. For robust network performance, a localized synchronization detection scheme based on relative timing and statistics of the PCO firing and the timing pulses ("sync") is reported. No active hand-shaking is required for nodes to detect synchronization. A self-reinforcement scheme also helps maintain synchronization even in the presence of miss-detections. Finally we discuss unique ways to exploit properties of pulse coupled oscillator networks to realize novel low power event communication, prioritization, localization and immediate neighborhood validation for low power wireless sensor applications

LOW-POWER IMPULSE-RADIO ULTRA-WIDEBAND TECHNIQUES FOR BIOMEDICAL APPLICATIONS.

Ph.DDOCTOR OF PHILOSOPH

Energy-Efficient Wireless Circuits and Systems for Internet of Things

As the demand of ultra-low power (ULP) systems for internet of thing (IoT) applications has been increasing, large efforts on evolving a new computing class is actively ongoing. The evolution of the new computing class, however, faced challenges due to hard constraints on the RF systems. Significant efforts on reducing power of power-hungry wireless radios have been done. The ULP radios, however, are mostly not standard compliant which poses a challenge to wide spread adoption. Being compliant with the WiFi network protocol can maximize an ULP radio’s potential of utilization, however, this standard demands excessive power consumption of over 10mW, that is hardly compatible with in ULP systems even with heavy duty-cycling. Also, lots of efforts to minimize off-chip components in ULP IoT device have been done, however, still not enough for practical usage without a clean external reference, therefore, this limits scaling on cost and form-factor of the new computer class of IoT applications. This research is motivated by those challenges on the RF systems, and each work focuses on radio designs for IoT applications in various aspects. First, the research covers several endeavors for relieving energy constraints on RF systems by utilizing existing network protocols that eventually meets both low-active power, and widespread adoption. This includes novel approaches on 802.11 communication with articulate iterations on low-power RF systems. The research presents three prototypes as power-efficient WiFi wake-up receivers, which bridges the gap between industry standard radios and ULP IoT radios. The proposed WiFi wake-up receivers operate with low power consumption and remain compatible with the WiFi protocol by using back-channel communication. Back-channel communication embeds a signal into a WiFi compliant transmission changing the firmware in the access point, or more specifically just the data in the payload of the WiFi packet. With a specific sequence of data in the packet, the transmitter can output a signal that mimics a modulation that is more conducive for ULP receivers, such as OOK and FSK. In this work, low power mixer-first receivers, and the first fully integrated ultra-low voltage receiver are presented, that are compatible with WiFi through back-channel communication. Another main contribution of this work is in relieving the integration challenge of IoT devices by removing the need for external, or off-chip crystals and antennas. This enables a small form-factor on the order of mm3-scale, useful for medical research and ubiquitous sensing applications. A crystal-less small form factor fully integrated 60GHz transceiver with on-chip 12-channel frequency reference, and good peak gain dual-mode on-chip antenna is presented.PHDElectrical and Computer EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/162975/1/jaeim_1.pd

Energy-efficient, short-range ultra-wideband radio transceivers

Short-range wireless communications continually attract interest from both industry and academia, and it is changing our life in every aspect in the last decade. The design of wireless transceivers is the bottleneck for variety applications, due to RF modeling inaccuracy, stringent FCC regulations over the transmitted power spectrum, interference, multi-path reflections, modulation scheme, receiver sensitivity, and synchronization. In addition, energy efficiency is always one of the most important design goals. Ultra-Wideband(UWB) is found to be very energy-efficient due to its low duty cycle and potentially high data rate due to its wide bandwidth. However, there still remain unsolved issues with UWB transceivers, such as pulse shaping, multi-path reflections, and receiver clock synchronization. To address these, novel techniques such as wireless multi-path equalization, pulse injection-locking for receiver clock synchronization, reconfigurable pulse shaping, low power wireless clock distribution, and an ultra-low-power super-regenerative receiver are implemented and verified on silicon. Three chips are designed and verified: a 3-5GHz Impulse-Radio(IR) UWB transceiver, a 3-60GHz all digital reconfigurable transmitter, and a 402-405MHz MICS/UWB(Sub-GHz) super-regenerative receiver incorporating wireless clock synchronization. A detailed design methodology, measurement results, and discussions are presented