A 1.2 V and 69 mW 60 GHz Multi-channel Tunable CMOS Receiver Design

A multi-channel receiver operating between 56 GHz and 70 GHz for coverage of different 60 GHz bands worldwide is implemented with a 90 nm Complementary Metal-Oxide Semiconductor (CMOS) process. The receiver containing an LNA, a frequency down-conversion mixer and a variable gain amplifier incorporating a band-pass filter is designed and implemented. This integrated receiver is tested at four channels of centre frequencies 58.3 GHz, 60.5 GHz, 62.6 GHz and 64.8 GHz, employing a frequency plan of an 8 GHz-intermediate frequency (IF). The achieved conversion gain by coarse gain control is between 4.8 dB–54.9 dB. The millimeter-wave receiver circuit is biased with a 1.2V supply voltage. The measured power consumption is 69 mW

An in-band full-duplex radio receiver with a passive vector modulator downmixer for self-interference cancellation

In-band full-duplex (FD) wireless, i.e., simultaneous transmission and reception at the same frequency, introduces strong self-interference (SI) that masks the signal to be received. This paper proposes a receiver in which a copy of the transmit signal is fed through a switched-resistor vector modulator (VM)that provides simultaneous downmixing, phase shift, and amplitude scaling and subtracts it in the analog baseband for up to 27 dB SI-cancellation. Cancelling before active baseband amplification avoids self-blocking, and highly linear mixers keep SIinduced distortion low, for a receiver SI-to-noise-and-distortionratio (SINDR) of up to 71.5 dB in 16.25 MHz BW. When combined with a two-port antenna with only 20 dB isolation, the low RX distortion theoretically allows sufficient digital cancellation for over 90 dB link budget, sufficient for short-range, low-power FD links

A self-interference-cancelling receiver for in-band full-duplex wireless with low distortion under cancellation of strong TX leakage

In-band full-duplex (FD) wireless communication, i.e. simultaneous transmission and reception at the same frequency, in the same channel, promises up to 2x spectral efficiency, along with advantages in higher network layers [1]. the main challenge is dealing with strong in-band leakage from the transmitter to the receiver (i.e. self-interference (SI)), as TX powers are typically >100dB stronger than the weakest signal to be received, necessitating TX-RX isolation and SI cancellation. Performing this SI-cancellation solely in the digital domain, if at all possible, would require extremely clean (low-EVM) transmission and a huge dynamic range in the RX and ADC, which is currently not feasible [2]. Cancelling SI entirely in analog is not feasible either, since the SI contains delayed TX components reflected by the environment. Cancelling these requires impractically large amounts of tunable analog delay. Hence, FD-solutions proposed thus far combine SI-rejection at RF, analog BB, digital BB and cross-domain

Hybrid MIMO Architectures for Millimeter Wave Communications: Phase Shifters or Switches?

Hybrid analog/digital MIMO architectures were recently proposed as an alternative for fully-digitalprecoding in millimeter wave (mmWave) wireless communication systems. This is motivated by the possible reduction in the number of RF chains and analog-to-digital converters. In these architectures, the analog processing network is usually based on variable phase shifters. In this paper, we propose hybrid architectures based on switching networks to reduce the complexity and the power consumption of the structures based on phase shifters. We define a power consumption model and use it to evaluate the energy efficiency of both structures. To estimate the complete MIMO channel, we propose an open loop compressive channel estimation technique which is independent of the hardware used in the analog processing stage. We analyze the performance of the new estimation algorithm for hybrid architectures based on phase shifters and switches. Using the estimated, we develop two algorithms for the design of the hybrid combiner based on switches and analyze the achieved spectral efficiency. Finally, we study the trade-offs between power consumption, hardware complexity, and spectral efficiency for hybrid architectures based on phase shifting networks and switching networks. Numerical results show that architectures based on switches obtain equal or better channel estimation performance to that obtained using phase shifters, while reducing hardware complexity and power consumption. For equal power consumption, all the hybrid architectures provide similar spectral efficiencies.Comment: Submitted to IEEE Acces

Temporal and spatial combining for 5G mmWave small cells

This chapter proposes the combination of temporal processing through Rake combining based on direct sequence-spread spectrum (DS-SS), and multiple antenna beamforming or antenna spatial diversity as a possible physical layer access technique for fifth generation (5G) small cell base stations (SBS) operating in the millimetre wave (mmWave) frequencies. Unlike earlier works in the literature aimed at previous generation wireless, the use of the beamforming is presented as operating in the radio frequency (RF) domain, rather than the baseband domain, to minimise power expenditure as a more suitable method for 5G small cells. Some potential limitations associated with massive multiple input-multiple output (MIMO) for small cells are discussed relating to the likely limitation on available antennas and resultant beamwidth. Rather than relying, solely, on expensive and potentially power hungry massive MIMO (which in the case of a SBS for indoor use will be limited by a physically small form factor) the use of a limited number of antennas, complimented with Rake combining, or antenna diversity is given consideration for short distance indoor communications for both the SBS) and user equipment (UE). The proposal’s aim is twofold: to solve eroded path loss due to the effective antenna aperture reduction and to satisfy sensitivity to blockages and multipath dispersion in indoor, small coverage area base stations. Two candidate architectures are proposed. With higher data rates, more rigorous analysis of circuit power and its effect on energy efficiency (EE) is provided. A detailed investigation is provided into the likely design and signal processing requirements. Finally, the proposed architectures are compared to current fourth generation long term evolution (LTE) MIMO technologies for their anticipated power consumption and EE

Frequency Multipliers in SiGe BiCMOS for Local Oscillator Generation in D-band Wireless Transceivers

Communications at millimeter-wave (mm-Wave) have drawn a lot of attention in recent years due to the wide available bandwidth which translates directly to higher data transmission capacity. Generation of the transceivers local oscillation (LO) is critical because many contrasting requirements, i.e. tuning range (TR), phase noise (PN), output power, and level of spurious tones, affect the system performance. Differently from what is commonly pursued at Radio Frequency, LO generation with a PLL embedding a VCO at the desired output frequency is not viable at mm-wave. A more promising approach consists of a PLL in the 10-20GHz range, where silicon VCOs feature the best figure of merit, followed by a frequency multiplier. In this thesis, a frequency multiplication chain is investigated to up-convert an LO signal from X-band to D-band by a multiplication factor of 12. The multiplication is done in steps of 3, 2, and 2. A sextupler chip comprises the tripler and the first doubler and the last doubler stage which upconverts the LO signal from E- to D-band is realized in a separate chip, all in a 55nm SiGe BiCMOS technology. The frequency tripler circuit is based on a novel circuit topology which yields a remarkable improvement on the suppression of the driving signal frequency at the output, compared to conventional designs exploiting transistors in class-C. The active core of the circuit approximates the transfer characteristic of a third-order polynomial that ideally produces only a third-harmonic of the input signal. Implemented in a separate break-out chip and consuming 23mW of DC power, the tripler demonstrates ~40dB suppression of the input signal and its 5th harmonic over 16% fractional bandwidth and robustness to power variation of the driving signal over a 15dB range. Including the E-band doubler, the sextupler chip achieves a peak output power of 1.7dBm at 74.4GHz and remains within 2dB variation from 70GHz to 82GHz, corresponding to 16% fractional BW. In this frequency range, the leakages of all harmonics are suppressed by more than 40dBc. The design of the D-band doubler was aimed at delivering high output power with high efficiency and high conversion gain. Toward this end, the efficiency of a push-push pair was improved by a stacked Colpitts oscillator to boost the power conversion gain by 10dB. Moreover, the common-collector configuration keeps separate the oscillator tank from the load, allowing independent optimization of the harmonic conversion efficiency and the load impedance for maximum power delivery. The measured performance of the test chip demonstrated Pout up to 8dBm at 130GHz with 13dB conversion gain and 6.3% Power Added Efficiency

Multicarrier Faster-than-Nyquist Signaling Transceivers: From Theory to Practice

The demand for spectrum resources in cellular systems worldwide has seen a tremendous escalation in the recent past. The mobile phones of today are capable of being cameras taking pictures and videos, able to browse the Internet, do video calling and much more than an yesteryear computer. Due to the variety and the amount of information that is being transmitted the demand for spectrum resources is continuously increasing. Efficient use of bandwidth resources has hence become a key parameter in the design and realization of wireless communication systems. Faster-than-Nyquist (FTN) signaling is one such technique that achieves bandwidth efficiency by making better use of the available spectrum resources at the expense of higher processing complexity in the transceiver. This thesis addresses the challenges and design trade offs arising during the hardware realization of Faster-than-Nyquist signaling transceivers. The FTN system has been evaluated for its achievable performance compared to the processing overhead in the transmitter and the receiver. Coexistence with OFDM systems, a more popular multicarrier scheme in existing and upcoming wireless standards, has been considered by designing FTN specific processing blocks as add-ons to the conventional transceiver chain. A multicarrier system capable of operating under both orthogonal and FTN signaling has been developed. The performance of the receiver was evaluated for AWGN and fading channels. The FTN system was able to achieve 2x improvement in bandwidth usage with similar performance as that of an OFDM system. The extra processing in the receiver was in terms of an iterative decoder for the decoding of FTN modulated signals. An efficient hardware architecture for the iterative decoder reusing the FTN specific processing blocks and realize different functionality has been designed. An ASIC implementation of this decoder was implemented in a 65nm CMOS technology and the implemented chip has been successfully verified for its functionality