A 128-point Multi-Path SC FFT Architecture

This paper presents a new radix-2^k multi-path FFT architecture, named MSC FFT, which is based on a single-path radix-2 serial commutator (SC) FFT architecture. The proposed multi-path architecture has a very high hardware utilization that results in a small chip area, while providing high throughput. In addition, the adoption of radix-2^k FFT algorithms allows for simplifying the rotators even further. It is achieved by optimizing the structure of the processing element (PE). The implemented architecture is a 128-point 4-parallel multi-path SC FFT using 90 nm process. Its area and power consumption at 250 MHz are only 0.167 mm2 and 14.81 mW, respectively. Compared with existing works, the proposed design reduces significantly the chip rea and the power consumption, while providing high throughput.Comment: Conference paper, ISCAS 2020, 5 page

Efficient FPGA implementation of high-throughput mixed radix multipath delay commutator FFT processor for MIMO-OFDM

This article presents and evaluates pipelined architecture designs for an improved high-frequency Fast Fourier Transform (FFT) processor implemented on Field Programmable Gate Arrays (FPGA) for Multiple Input Multiple Output Orthogonal Frequency Division Multiplexing (MIMO-OFDM). The architecture presented is a Mixed-Radix Multipath Delay Commutator. The presented parallel architecture utilizes fewer hardware resources compared to Radix-2 architecture, while maintaining simple control and butterfly structures inherent to Radix-2 implementations. The high-frequency design presented allows enhancing system throughput without requiring additional parallel data paths common in other current approaches, the presented design can process two and four independent data streams in parallel and is suitable for scaling to any power of two FFT size N. FPGA implementation of the architecture demonstrated significant resource efficiency and high-throughput in comparison to relevant current approaches within literature. The proposed architecture designs were realized with Xilinx System Generator (XSG) and evaluated on both Virtex-5 and Virtex-7 FPGA devices. Post place and route results demonstrated maximum frequency values over 400 MHz and 470 MHz for Virtex-5 and Virtex-7 FPGA devices respectively

FPGA Implementation of Fast Fourier Transform Core Using NEDA

Transforms like DFT are a major block in communication systems such as OFDM, etc. This thesis reports architecture of a DFT core using NEDA. The advantage of the proposed architecture is that the entire transform can be implemented using adder/subtractors and shifters only, thus minimising the hardware requirement compared to other architectures. The proposed design is implemented for 16-bit data path (12–bit for comparison) considering both integer representation as well as fixed point representation, thus increasing the scope of usage. The proposed design is mapped on to Xilinx XC2VP30 FPGA, which is fabricated using 130 nm process technology. The maximum on board frequency of operation of the proposed design is 122 MHz. NEDA is one of the techniques to implement many signal processing systems that require multiply and accumulate units. FFT is one of the most employed blocks in many communication and signal processing systems. The FPGA implementation of a 16 point radix-4 complex FFT is proposed. The proposed design has improvement in terms of hardware utilization compared to traditional methods. The design has been implemented on a range of FPGAs to compare the performance. The maximum frequency achieved is 114.27 MHz on XC5VLX330 FPGA and the maximum throughput, 1828.32 Mbit/s and minimum slice delay product, 9.18. The design is also implemented using synopsys DC synthesis in both 65 nm and 180 nm technology libraries. The advantages of multiplier-less architectures are reduced hardware and improved latency. The multiplier-less architectures for the implementation of radix-2^2 folded pipelined complex FFT core are based on NEDA. The number of points considered in the work is sixteen and the folding is done by a factor of four. The proposed designs are implemented on Xilinx XC5VSX240T FPGA. Proposed designs based on NEDA have reduced area over 83%. The observed slice-delay product for NEDA based designs are 2.196 and 5.735

Efficient multiplier-less VLSI architectures for folded pipelined complex FFT core

Fast Fourier transform (FFT) has become ubiquitous in many engineering applications. FFT is one of the most employed blocks in many communication and signal processing systems. Efficient algorithms are being designed to improve the architecture of FFT. Higher radix FFT algorithms have the traditional advantage of using less number of computational elements and are more suitable for calculating FFT of long data sequence. Among the different proposed algorithms, the split-radix FFT has shown considerable improvement in terms of reducing hardware complexity of the architecture compared to radix-2 and radix-4 FFT algorithms. Here radix-4, radix-8, and split-radix algorithms have been used in the design of different proposed complex FFT cores. The growing popularity of adopting virtual instrumentation (modular, customizable, software-defined instrumentation) has only became possible due to the use of LabVIEW with a highly interactive process known as graphical system design. The CompactRIO programmable automation controller is an advanced embedded control and data acquisition system designed for applications that require high performance and reliability. The work explains the real-time implementation of 256-point FFT and finding the power spectrum using LabVIEW and CompactRIO. New distributed arithmetic (NEDA) is one of the most used techniques in implementing multiplier-less architectures of many digital systems. In this thesis, four architectures for different FFT cores have been proposed: • Real-time implementation of FFT using CompactRIO • 32-Point Complex FFT Core Using Split-Radix Algorithm • 64-Point Complex FFT Core Using Radix-4 Algorithm • 64-Point Complex FFT Core Using Radix-8 Algorithm The proposed designs have implemented in both FPGA as well as ASIC design flows. 180nm process technology is being used for ASIC implementation. The results show the improvements of proposed designs compared to the other existing architectures

Deterministic analysis of the accuracy in FFT hardware architectures

Projecte realitzat en el marc d'un programa de mobilitat amb la Linköpings Universitet.[ANGLÈS] This Master Thesis studies the different quantization effects in hardware architecture due to the use of finite word lenght. This master thesis gives a deterministic analysis with relation to the accuracy and presents a relationship between input bits and coefficient bits for minimizing recourses and to obtain the best relation with the accuracy. Furthermore, the objective of this master thesis is to find a direct relation between the input bits and coefficient bits. This can be used as guide for the design of FFT hardware architectures (Fast Fourier Transform).[CASTELLÀ] Este proyecto fin de carrera estudia los efectos de diferentes cuantificaciones encontradas en diferentes arquitecturas de hardware debido al uso de un tamaño finito en los datos. Este proyecto da un análisis determinista con respecto a la exactitud y presenta una relación entre los bits de entrada y los bits de coeficientes para minimizar recursos y para conseguir la mejor relación con la exactitud. Además, el objetivo de este proyecto es encontrar una relación directa entre los bits de entrada y bits de coeficiente. Esto se puede utilizar como guía para el diseño de arquitecturas de hardware de una FFT (Transformada rápida de Fourier).[CATALÀ] Aquest projecte final de carrera estudia els efectes de quantificació de diferents arquitectures de hardware causades per l'ús d'una longitud finita en les dades. Aquest projecta dóna una anàlisi determinista pel que fa a l'exactitud i presenta una relació entre els bits d'entrada i els bits de coeficients per tal de minimitzar recursos i per aconseguir la millor relació amb l'exactitud. A més, l'objectiu d'aquest projecte és trobar una relació directa entre els bits d'entrada i bits de coeficients. Això es pot utilitzar com a guia per al disseny d'arquitectures de hardware d'una FFT (Transformada ràpida de Fourier)

Selected Papers from IEEE ICASI 2019

The 5th IEEE International Conference on Applied System Innovation 2019 (IEEE ICASI 2019, https://2019.icasi-conf.net/), which was held in Fukuoka, Japan, on 11–15 April, 2019, provided a unified communication platform for a wide range of topics. This Special Issue entitled “Selected Papers from IEEE ICASI 2019” collected nine excellent papers presented on the applied sciences topic during the conference. Mechanical engineering and design innovations are academic and practical engineering fields that involve systematic technological materialization through scientific principles and engineering designs. Technological innovation by mechanical engineering includes information technology (IT)-based intelligent mechanical systems, mechanics and design innovations, and applied materials in nanoscience and nanotechnology. These new technologies that implant intelligence in machine systems represent an interdisciplinary area that combines conventional mechanical technology and new IT. The main goal of this Special Issue is to provide new scientific knowledge relevant to IT-based intelligent mechanical systems, mechanics and design innovations, and applied materials in nanoscience and nanotechnology

Adaptive Baseband Pro cessing and Configurable Hardware for Wireless Communication

The world of information is literally at one’s fingertips, allowing access to previously unimaginable amounts of data, thanks to advances in wireless communication. The growing demand for high speed data has necessitated theuse of wider bandwidths, and wireless technologies such as Multiple-InputMultiple-Output (MIMO) have been adopted to increase spectral efficiency.These advanced communication technologies require sophisticated signal processing, often leading to higher power consumption and reduced battery life.Therefore, increasing energy efficiency of baseband hardware for MIMO signal processing has become extremely vital. High Quality of Service (QoS)requirements invariably lead to a larger number of computations and a higherpower dissipation. However, recognizing the dynamic nature of the wirelesscommunication medium in which only some channel scenarios require complexsignal processing, and that not all situations call for high data rates, allowsthe use of an adaptive channel aware signal processing strategy to provide adesired QoS. Information such as interference conditions, coherence bandwidthand Signal to Noise Ratio (SNR) can be used to reduce algorithmic computations in favorable channels. Hardware circuits which run these algorithmsneed flexibility and easy reconfigurability to switch between multiple designsfor different parameters. These parameters can be used to tune the operations of different components in a receiver based on feedback from the digitalbaseband. This dissertation focuses on the optimization of digital basebandcircuitry of receivers which use feedback to trade power and performance. Aco-optimization approach, where designs are optimized starting from the algorithmic stage through the hardware architectural stage to the final circuitimplementation is adopted to realize energy efficient digital baseband hardwarefor mobile 4G devices. These concepts are also extended to the next generation5G systems where the energy efficiency of the base station is improved.This work includes six papers that examine digital circuits in MIMO wireless receivers. Several key blocks in these receiver include analog circuits thathave residual non-linearities, leading to signal intermodulation and distortion.Paper-I introduces a digital technique to detect such non-linearities and calibrate analog circuits to improve signal quality. The concept of a digital nonlinearity tuning system developed in Paper-I is implemented and demonstratedin hardware. The performance of this implementation is tested with an analogchannel select filter, and results are presented in Paper-II. MIMO systems suchas the ones used in 4G, may employ QR Decomposition (QRD) processors tosimplify the implementation of tree search based signal detectors. However,the small form factor of the mobile device increases spatial correlation, whichis detrimental to signal multiplexing. Consequently, a QRD processor capableof handling high spatial correlation is presented in Paper-III. The algorithm and hardware implementation are optimized for carrier aggregation, which increases requirements on signal processing throughput, leading to higher powerdissipation. Paper-IV presents a method to perform channel-aware processingwith a simple interpolation strategy to adaptively reduce QRD computationcount. Channel properties such as coherence bandwidth and SNR are used toreduce multiplications by 40% to 80%. These concepts are extended to usetime domain correlation properties, and a full QRD processor for 4G systemsfabricated in 28 nm FD-SOI technology is presented in Paper-V. The designis implemented with a configurable architecture and measurements show thatcircuit tuning results in a highly energy efficient processor, requiring 0.2 nJ to1.3 nJ for each QRD. Finally, these adaptive channel-aware signal processingconcepts are examined in the scope of the next generation of communicationsystems. Massive MIMO systems increase spectral efficiency by using a largenumber of antennas at the base station. Consequently, the signal processingat the base station has a high computational count. Paper-VI presents a configurable detection scheme which reduces this complexity by using techniquessuch as selective user detection and interpolation based signal processing. Hardware is optimized for resource sharing, resulting in a highly reconfigurable andenergy efficient uplink signal detector