차세대 자동차용 카메라 데이터 통신을 위한 비대칭 동시 양방향 송수신기의 설계

학위논문(박사) -- 서울대학교대학원 : 공과대학 전기·정보공학부, 2022.2. 정덕균.본 학위 논문에서는 차세대 자동차용 카메라 링크를 위해 높은 속도의 4레벨 펄스 진폭 변조 신호와 낮은 속도의 2레벨 펄스 진폭 변조 신호를 통신하는 비대칭 동시 양방향 송수신기의 설계 기술에 대해 제안하고 검증되었다. 첫번째 프로토타입 설계에서는, 10B6Q 직류 밸런스 코드를 탑재한 4레벨 펄스 진폭 변조 송신기와 고정된 데이터와 참조 레벨을 가지는 4레벨 펄스 진폭 변조 적응형 수신기에 대한 내용이 기술되었다. 4레벨 펄스 진폭 변조 송신기에서는 교류 연결 링크 시스템에 대응하기 위한 면적 및 전력 효율성이 좋은 10B6Q 코드가 제안되었다. 이 코드는 직류 밸런스를 맞추고 연속적으로 같은 심볼을 가지는 길이를 6개로 제한 시킨다. 비록 여기서는 입력 데이터 길이 10비트를 사용하였지만, 제안된 기술은 카메라의 다양한 데이터 타입에 대응할 수 있도록 입력 데이터 길이에 대한 확장성을 가진다. 반면, 4레벨 펄스 진폭 변조 적응형 수신기에서는, 샘플러의 옵셋을 최적으로 제거하여 더 낮은 비트에러율을 얻기 위해서, 기존의 데이터 및 참조 레벨을 조절하는 대신, 이 레벨들은 고정시키고 가변 게인 증폭기를 적응형으로 조절하도록 하였다. 상기 10B6Q 코드 및 고정 데이터 및 참조레벨 기술을 가진 프로토타입 칩들은 40 나노미터 상호보완형 메탈 산화 반도체 공정으로 제작되었고 칩 온 보드 형태로 평가되었다. 10B6Q 코드는 합성 게이트 숫자는 645개와 함께 단 0.0009 mm2 의 면적 만을 차지한다. 또한, 667 MHz 동작 주파수에서 단 0.23 mW 의 전력을 소모한다. 10B6Q 코드를 탑재한 송신기에서 8-Gb/s 4레벨 펄스 진폭 변조 신호를 고정 데이터 및 참조 레벨을 가지는 적응형 수신기로 12-m 케이블 (22-dB 채널 로스) 을 통해서 보낸 결과 최소 비트 에러율 108 을 달성하였고, 비트 에러율 105 에서는 아이 마진이 0.15 UI x 50 mV 보다 크게 측정되었다. 송수신기를 합친 전력 소모는 65.2 mW (PLL 제외) 이고, 성과의 대표수치는 0.37 pJ/b/dB 를 보여주었다. 첫번째 프로토타입 설계을 포함하여 개선된 두번째 프로토타입 설계에서는, 12-Gb/s 4레벨 펄스 진폭 변조 정방향 채널 신호와 125-Mb/s 2레벨 펄스 진폭 변조 역방향 채널 신호를 탑재한 비대칭 동시 양방향 송수신기에 대해 기술되고 검증되었다. 제안된 넓은 선형 범위를 가지는 하이브리드는 gmC 저대역 통과 필터와 에코 제거기와 함께 아웃바운드 신호를 24 dB 이상 효율적으로 감소시켰다. 또한, 넓은 선형 범위를 가지는 하이브리드와 함께 게인 감소기를 형성하게 되는 선형 범위 증폭기를 통해 4레벨 펄스 진폭 변조 신호의 선형성과 진폭의 트레이드 오프 관계를 깨는 것이 가능하였다. 동시 양방향 송수신기 칩은 40 나노미터 상호보완형 메탈 산화 반도체 공정으로 제작되었다. 상기 설계 기술들을 이용하여, 4레벨 펄스 진폭 변조 및 2레벨 펄스 진폭 변조 송수신기 모두 5m 채널 (채널 로스 15.9 dB) 에서 1E-12 보다 낮은 비트 에러율을 달성하였고, 총 78.4 mW 의 전력 소모를 기록하였다. 종합적인 송수신기는 성과 대표지표로 0.41 pJ/b/dB 와 함께 동시 양방향 통신 아래에서 4레벨 펄스 진폭 변조 신호 및 2레벨 펄스 진폭 변조 신호 각각에서 아이 마진 0.15 UI 와 0.57 UI 를 달성하였다. 이 수치는 성과 대표지표 0.5 이하를 가지는 기존 동시 양방향 송수신기와의 비교에서 최고의 아이 마진을 기록하였다.In this dissertation, design techniques of a highly asymmetric simultaneous bidirectional (SB) transceivers with high-speed PAM-4 and low-speed PAM-2 signals are proposed and demonstrated for the next-generation automotive camera link. In a first prototype design, a PAM-4 transmitter with 10B6Q DC balance code and a PAM-4 adaptive receiver with fixed data and threshold levels (dtLevs) are presented. In PAM-4 transmitter, an area- and power-efficient 10B6Q code for an AC coupled link system that guarantees DC balance and limited run length of six is proposed. Although the input data width of 10 bits is used here, the proposed scheme has an extensibility for the input data width to cover various data types of the camera. On the other hand, in the PAM-4 adaptive receiver, to optimally cancel the sampler offset for a lower BER, instead of adjusting dtLevs, the gain of a programmable gain amplifier is adjusted adaptively under fixed dtLevs. The prototype chips including above proposed 10B6Q code and fixed dtLevs are fabricated in 40-nm CMOS technology and tested in chip-on-board assembly. The 10B6Q code only occupies an active area of 0.0009 mm2 with a synthesized gate count of 645. It also consumes 0.23 mW at the operating clock frequency of 667 MHz. The transmitter with 10B6Q code delivers 8-Gb/s PAM-4 signal to the adaptive receiver using fixed dtLevs through a lossy 12-m cable (22-dB channel loss) with a BER of 1E-8, and the eye margin larger than 0.15 UI x 50 mV is measured for a BER of 1E-5. The proto-type chips consume 65.2 mW (excluding PLL), exhibiting an FoM of 0.37 pJ/b/dB. In a second prototype design advanced from the first prototypes, An asymmetric SB transceivers incorporating a 12-Gb/s PAM-4 forward channel and a 125-Mb/s PAM-2 back channel are presented and demonstrated. The proposed wide linear range (WLR) hybrid combined with a gmC low-pass filter and an echo canceller effectively suppresses the outbound signals by more than 24dB. In addition, linear range enhancer which forms a gain attenuator with WLR hybrid breaks the trade-off between the linearity and the amplitude of the PAM-4 signal. The SB transceiver chips are separately fabricated in 40-nm CMOS technology. Using above design techniques, both PAM-4 and PAM-2 SB transceivers achieve BER less than 1E-12 over a 5-m channel (15.9 dB channel loss), consuming 78.4 mW. The overall transceivers achieve an FoM of 0.41 pJ/b/dB and eye margin (at BER of 1E-12) of 0.15 UI and 0.57 UI for the forward PAM-4 and back PAM-2 signals, respectively, under SB communication. This is the best eye margin compared to the prior art SB transceivers with an FoM less than 0.5.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 DISSERTATION ORGANIZATION 4 CHAPTER 2 BACKGROUND ON AUTOMOTIVE CAMERA LINK 6 2.1 OVERVIEW 6 2.2 SYSTEM REQUIREMENTS 10 2.2.1 CHANNEL 10 2.2.2 POWER OVER DIFFERENTIAL LINE (PODL) 12 2.2.3 AC COUPLING AND DC BALANCE CODE 15 2.2.4 SIMULTANEOUS BIDIRECTIONAL COMMUNICATION 18 2.2.4.1 HYBRID 18 2.2.4.2 ECHO CANCELLER 20 2.2.5 ADAPTIVE RECEIVE EQUALIZATION 22 CHAPTER 3 AREA AND POWER EFFICIENT 10B6Q ENCODER FOR DC BALANCE 25 3.1 INTRODUCTION 25 3.2 PRIOR WORKS 28 3.3 PROPOSED AREA- AND POWER-EFFICIENT 10B6Q PAM-4 CODER 30 3.4 DESIGN OF THE 10B6Q CODE 33 3.4.1 PAM-4 DC BALANCE 35 3.4.2 PAM-4 TRANSITION DENSITY 35 3.4.3 10B6Q DECODER 37 3.5 IMPLEMENTATION AND MEASUREMENT RESULTS 40 CHAPTER 4 PAM-4 TRANSMITTER AND ADAPTIVE RECEIVER WITH FIXED DATA AND THRESHOLD LEVELS 45 4.1 INTRODUCTION 45 4.2 PRIOR WORKS 47 4.3 ARCHITECTURE AND IMPLEMENTATION 49 4.2.1 PAM-4 TRANSMITTER 49 4.2.2 PAM-4 ADAPTIVE RECEIVER 52 4.3 MEASUREMENT RESULTS 62 CHAPTER 5 ASYMMETRIC SIMULTANEOUS BIDIRECTIONAL TRANSCEIVERS USING WIDE LINEAR RANGE HYBRID 68 5.1 INTRODUCTION 68 5.2 PRIOR WORKS 70 5.3 WIDE LINEAR RANGE (WLR) HYBRID 75 5.3 IMPLEMENTATION 78 5.3.1 SERIALIZER (SER) DESIGN 78 5.3.2 DESERIALIZER (DES) DESIGN 79 5.4 HALF CIRCUIT ANALYSIS OF WLR HYBRID AND LRE 82 5.5 MEASUREMENT RESULTS 88 CHAPTER 6 CONCLUSION 97 BIBLIOGRAPHY 99 초 록 106박

A High-speed and Low Power Electrical Link Transceiver

On-chip wires will present increasing latency and energy problems as VLSI technologies continue to scale. Interconnects have an RC-limited bandwidth approximately proportional to the area of the metal cross section and inversely proportional to the squared length. To overcome RC-limited channels, an energy-efficient on-chip transceiver is presented that contains a hybrid transmitter, a current-sense receiver, and self-testing blocks. The main goal of this research is having a relatively low-power transceiver, which can be used as an on-chip communication system. By adding a pre-emphasis circuit in the transmitter, pre-cursor inter-symbol interference can be canceled. A hybrid transmitter which combines voltage-mode pre-emphasis with a current-mode main driver is used. This structure can save pre-emphasis current, and leads to reduced power dissipation especially in the static situation. A current-sense amplifier is implemented with a cross-coupled stage and an active inductor equalizer at the receiver, in order to boost the data rate while maintaining good energy efficiency. An offset cancelation circuit is incorporated to make a robust comparator for the receiver. According to simulation results, the transceiver has low power consumption with 1.2 V, 130 nm CMOS technology. The performance shows that it operates at 8 Gb/s over a 5 mm and 19 dB loss differential channel. The overall dynamic power consumption is 2.05 mW, without the PRBS generator/checker. Therefore, this transceiver has high data rate and low power consumption

차세대 HBM 용 고집적, 저전력 송수신기 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 정덕균.This thesis presents design techniques for high-density power-efficient transceiver for the next-generation high bandwidth memory (HBM). Unlike the other memory interfaces, HBM uses a 3D-stacked package using through-silicon via (TSV) and a silicon interposer. The transceiver for HBM should be able to solve the problems caused by the 3D-stacked package and TSV. At first, a data (DQ) receiver for HBM with a self-tracking loop that tracks a phase skew between DQ and data strobe (DQS) due to a voltage or thermal drift is proposed. The self-tracking loop achieves low power and small area by uti-lizing an analog-assisted baud-rate phase detector. The proposed pulse-to-charge (PC) phase detector (PD) converts the phase skew to a voltage differ-ence and detects the phase skew from the voltage difference. An offset calibra-tion scheme that can compensates for a mismatch of the PD is also proposed. The proposed calibration scheme operates without any additional sensing cir-cuits by taking advantage of the write training of HBM. Fabricated in 65 nm CMOS, the DQ receiver shows a power efficiency of 370 fJ/b at 4.8 Gb/s and occupies 0.0056 mm2. The experimental results show that the DQ receiver op-erates without any performance degradation under a ± 10% supply variation. In a second prototype IC, a high-density transceiver for HBM with a feed-forward-equalizer (FFE)-combined crosstalk (XT) cancellation scheme is pre-sented. To compensate for the XT, the transmitter pre-distorts the amplitude of the FFE output according to the XT. Since the proposed XT cancellation (XTC) scheme reuses the FFE implemented to equalize the channel loss, additional circuits for the XTC is minimized. Thanks to the XTC scheme, a channel pitch can be significantly reduced, allowing for the high channel density. Moreover, the 3D-staggered channel structure removes the ground layer between the verti-cally adjacent channels, which further reduces a cross-sectional area of the channel per lane. The test chip including 6 data lanes is fabricated in 65 nm CMOS technology. The 6-mm channels are implemented on chip to emulate the silicon interposer between the HBM and the processor. The operation of the XTC scheme is verified by simultaneously transmitting 4-Gb/s data to the 6 consecutive channels with 0.5-um pitch and the XTC scheme reduces the XT-induced jitter up to 78 %. The measurement result shows that the transceiver achieves the throughput of 8 Gb/s/um. The transceiver occupies 0.05 mm2 for 6 lanes and consumes 36.6 mW at 6 x 4 Gb/s.본 논문에서는 차세대 HBM을 위한 고집적 저전력 송수신기 설계 방법을 제안한다. 첫 번째로, 전압 및 온도 변화에 의한 데이터와 클럭 간 위상 차이를 보상할 수 있는 자체 추적 루프를 가진 데이터 수신기를 제안한다. 제안하는 자체 추적 루프는 데이터 전송 속도와 같은 속도로 동작하는 위상 검출기를 사용하여 전력 소모와 면적을 줄였다. 또한 메모리의 쓰기 훈련 (write training) 과정을 이용하여 효과적으로 위상 검출기의 오프셋을 보상할 수 있는 방법을 제안한다. 제안하는 데이터 수신기는 65 nm 공정으로 제작되어 4.8 Gb/s에서 370 fJ/b을 소모하였다. 또한 10 % 의 전압 변화에 대하여 안정적으로 동작하는 것을 확인하였다. 두 번째로, 피드 포워드 이퀄라이저와 결합된 크로스 토크 보상 방식을 활용한 고집적 송수신기를 제안한다. 제안하는 송신기는 크로스 토크 크기에 해당하는 만큼 송신기 출력을 왜곡하여 크로스 토크를 보상한다. 제안하는 크로스 토크 보상 방식은 채널 손실을 보상하기 위해 구현된 피드 포워드 이퀄라이저를 재활용함으로써 추가적인 회로를 최소화한다. 제안하는 송수신기는 크로스 토크가 보상 가능하기 때문에, 채널 간격을 크게 줄여 고집적 통신을 구현하였다. 또한 집적도를 더 증가시키기 위해 세로로 인접한 채널 사이의 차폐 층을 제거한 적층 채널 구조를 제안한다. 6개의 송수신기를 포함한 프로토타입 칩은 65 nm 공정으로 제작되었다. HBM과 프로세서 사이의 silicon interposer channel 을 모사하기 위한 6 mm 의 채널이 칩 위에 구현되었다. 제안하는 크로스 토크 보상 방식은 0.5 um 간격의 6개의 인접한 채널에 동시에 데이터를 전송하여 검증되었으며, 크로스 토크로 인한 지터를 최대 78 % 감소시켰다. 제안하는 송수신기는 8 Gb/s/um 의 처리량을 가지며 6 개의 송수신기가 총 36.6 mW의 전력을 소모하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 4 CHAPTER 2 BACKGROUND ON HIGH-BANDWIDTH MEMORY 6 2.1 OVERVIEW 6 2.2 TRANSCEIVER ARCHITECTURE 10 2.3 READ/WRITE OPERATION 15 2.3.1 READ OPERATION 15 2.3.2 WRITE OPERATION 19 CHAPTER 3 BACKGROUNDS ON COUPLED WIRES 21 3.1 GENERALIZED MODEL 21 3.2 EFFECT OF CROSSTALK 26 CHAPTER 4 DQ RECEIVER WITH BAUD-RATE SELF-TRACKING LOOP 29 4.1 OVERVIEW 29 4.2 FEATURES OF DQ RECEIVER FOR HBM 33 4.3 PROPOSED PULSE-TO-CHARGE PHASE DETECTOR 35 4.3.1 OPERATION OF PULSE-TO-CHARGE PHASE DETECTOR 35 4.3.2 OFFSET CALIBRATION 37 4.3.3 OPERATION SEQUENCE 39 4.4 CIRCUIT IMPLEMENTATION 42 4.5 MEASUREMENT RESULT 46 CHAPTER 5 HIGH-DENSITY TRANSCEIVER FOR HBM WITH 3D-STAGGERED CHANNEL AND CROSSTALK CANCELLATION SCHEME 57 5.1 OVERVIEW 57 5.2 PROPOSED 3D-STAGGERED CHANNEL 61 5.2.1 IMPLEMENTATION OF 3D-STAGGERED CHANNEL 61 5.2.2 CHANNEL CHARACTERISTICS AND MODELING 66 5.3 PROPOSED FEED-FORWARD-EQUALIZER-COMBINED CROSSTALK CANCELLATION SCHEME 72 5.4 CIRCUIT IMPLEMENTATION 77 5.4.1 OVERALL ARCHITECTURE 77 5.4.2 TRANSMITTER WITH FFE-COMBINED XTC 79 5.4.3 RECEIVER 81 5.5 MEASUREMENT RESULT 82 CHAPTER 6 CONCLUSION 93 BIBLIOGRAPHY 95 초 록 102Docto

Design Techniques for High Pin Efficiency Wireline Transceivers

While the majority of wireline research investigates bandwidth improvement and how to overcome the high channel loss, pin efficiency is also critical in high-performance wireline applications. This dissertation proposes two different implementations for high pin efficiency wireline transceivers. The first prototype achieves twice pin efficiency than unidirectional signaling, which is 32Gb/s simultaneous bidirectional transceiver supporting transmission and reception on the same channel at the same time. It includes an efficient low-swing voltage-mode driver with an R-gm hybrid for signal separation, combining the continuous-time-linear-equalizer (CTLE) and echo cancellation (EC) in a single stage, and employing a low-complexity 5/4X CDA system. Support of a wide range of channels is possible with foreground adaptation of the EC finite impulse response (FIR) filter taps with a sign-sign least-mean-square (SSLMS) algorithm. Fabricated in TSMC 28-nm CMOS, the 32Gb/s SBD transceiver occupies $0.09 mm^{2}$ area and achieves 16Gb/s uni-directional and 32Gb/s simultaneous bi-directional signals. 32Gb/s SBD operation consumes 1.83mW/Gb/s with 10.8dB channel loss at Nyquist rate. The second prototype presents an optical transmitter with a quantum-dot (QD) microring laser. This can support wavelength-division multiplexing allowing for high pin efficiency application by packing multiple high-bandwidth signals onto one optical channel. The development QD microring laser model accurately captures the intrinsic photonic high-speed dynamics and allows for the future co-design of the circuits and photonic device. To achieve higher bandwidth than intrinsic one, utilizing both techniques of optical injection locking (OIL) and 2-tap asymmetric Feed-forward equalizer (FFE) can perform 22Gb/s operation with 3.2mW/Gb/s. The first hybrid-integration directly-modulated OIL QD microring laser system is demonstrated

Design Techniques for Energy Efficient Multi-GB/S Serial I/O Transceivers

Total I/O bandwidth demand is growing in high-performance systems due to the emergence of many-core microprocessors and in mobile devices to support the next generation of multi-media features. High-speed serial I/O energy efficiency must improve in order to enable continued scaling of these parallel computing platforms in applications ranging from data centers to smart mobile devices. The first work, a low-power forwarded-clock I/O transceiver architecture is presented that employs a high degree of output/input multiplexing, supply-voltage scaling with data rate, and low-voltage circuit techniques to enable low-power operation. The transmitter utilizes a 4:1 output multiplexing voltage-mode driver along with 4-phase clocking that is efficiently generated from a passive poly-phase filter. The output driver voltage swing is accurately controlled from 100-200 mV_(ppd) using a low-voltage pseudo-differential regulator that employs a partial negative-resistance load for improved low frequency gain. 1:8 input de-multiplexing is performed at the receiver equalizer output with 8 parallel input samplers clocked from an 8-phase injection-locked oscillator that provides more than 1UI de-skew range. Low-power high-speed serial I/O transmitters which include equalization to compensate for channel frequency dependent loss are required to meet the aggressive link energy efficiency targets of future systems. The second work presents a low power serial link transmitter design that utilizes an output stage which combines a voltage-mode driver, which offers low static-power dissipation, and current-mode equalization, which offers low complexity and dynamic-power dissipation. The utilization of current-mode equalization decouples the equalization settings and termination impedance, allowing for a significant reduction in pre-driver complexity relative to segmented voltage-mode drivers. Proper transmitter series termination is set with an impedance control loop which adjusts the on-resistance of the output transistors in the driver voltage-mode portion. Further reductions in dynamic power dissipation are achieved through scaling the serializer and local clock distribution supply with data rate. Finally, it presents that a scalable quarter-rate transmitter employs an analog-controlled impedance-modulated 2-tap voltage-mode equalizer and achieves fast power-state transitioning with a replica-biased regulator and ILO clock generation. Capacitively-driven 2 mm global clock distribution and automatic phase calibration allows for aggressive supply scaling

Design of High-Speed Power-Efficient Transmitter with Time-Based Equalization

본 논문은 고속, 저전력으로 동작하는 유선 송신기의 설계에 대해 설명하고 있다. 분리되지 않은 출력 드라이버가 있는 에너지 효율적인 전압 모드 송신기는 위상 지연 분석을 기반으로 시간 영역에서 채널 손실을 보상한다. 직렬화된 데이터 스트림이 아닌 송신 클럭의 위상을 변조함으로써 제안된 송신기는 데이터 의존적 지터를 크게 줄인다. 수평 아이 오프닝은 전송된 데이터의 실행 길이에 따라 제로 크로싱 시간 변동을 보상함으로써 개선된다. 제안된 방식은 큰 신호 및 스위칭 전력을 소비하는 많은 드라이버 슬라이스를 제거함으로써 드라이버 복잡성을 크게 줄인다. 프로토타입 칩은 28 nm CMOS 공정으로 제작되었으며 0.045 mm2 의 실제 면적을 차지한다. 측정된 결과는 제안된 송신기가 1.0 V 공급에서 440 mVppd의 출력 스윙으로 22 Gb/s의 속도에서 0.95 pJ/b의 에너지 효율을 달성함을 보여준다. 또한 피크 대 피크 지터는 15.0 dB 손실의 채널에 대해 제안된 위상 지연 보상을 통해 22 Gb/s의 속도에서 34 ps에서 20 ps로 감소된다.In this thesis, a design of high-speed, power-efficient wireline transmitter is reported. An energy-efficient voltage-mode transmitter with an un-segmented output driver equalizes channel loss in the time-domain based on the phase de-lay analysis. By modulating the phase of the transmitting clock rather than the serialized data stream, the proposed transmitter significantly reduces the data-dependent jitter. The horizontal eye-opening is improved by compensating for the zero-crossing time variation dependent on the run-length of the transmitted data. The proposed scheme significantly reduces the driver complexity by elim-inating many driver slices that consume significant signaling and switching power. The prototype chip has been fabricated in a 28-nm CMOS process and occupies an active area of 0.045 mm2. The measured results show that the pro-posed transmitter achieves an energy efficiency of 0.95 pJ/b at 22 Gb/s with an output swing of 440 mVppd at 1.0 V supply. In addition, peak-to-peak jitter is reduced from 34 ps to 20 ps at 22 Gb/s with the proposed phase delay compen-sation over the channel with a 15.0 dB loss.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 4 CHAPTER 2 BACKGROUNDS 5 2.1 OVERVIEW 5 2.2 FEED-FORWARD EQUALIZATION 7 2.2.1 AMPLITUDE-DOMAIN EQUALIZATION 7 2.2.2 PHASE-DOMAIN EQUALIZATION 12 2.2.3 PULSE-WIDTH MODULATION 18 2.3 ADAPTIVE FEED-FORWARD EQUALIZATION 21 2.3.1 AMPLITUDE-DOMAIN EQUALIZATION 21 2.3.2 PULSE-WIDTH MODULATION 24 CHAPTER 3 DESIGN OF THE TIME-BASED FEED-FORWARD EQUALIZATION OF THE TRANSMITTER 26 3.1 OVERVIEW 26 3.2 BASIC CONCEPT OF TIME-BASED FFE 28 3.2.1 ZERO-CROSSING TIME 28 3.2.2 PHASE DELAY 32 3.2.3 FINDING THE OPTIMUM COEFFICIENT 39 3.2.4 COMPARISON WITH CONVENTIONAL FFE 43 3.3 ADAPTIVE TIME-BASED FFE 50 3.3.1 OVERVIEW 50 3.3.2 BEHAVIORAL MODELING 51 3.3.3 SIMULATION RESULTS 53 3.4 TRANSMITTER IMPLEMENTATION 60 3.4.1 OVERVIEW 60 3.4.2 PHASE MODULATION 62 3.4.3 SERIALIZER AND CLOCK PATH 67 CHAPTER 4 MEASUREMENT 71 4.1 OVERVIEW 71 4.2 EYE DIAGRAM 76 4.3 POWER CONSUMPTION 81 CHAPTER 5 CONCLUSION 84 BIBLIOGRAPHY 86 초 록 92박

Integrated Circuit Design for Hybrid Optoelectronic Interconnects

This dissertation focuses on high-speed circuit design for the integration of hybrid optoelectronic interconnects. It bridges the gap between electronic circuit design and optical device design by seamlessly incorporating the compact Verilog-A model for optical components into the SPICE-like simulation environment, such as the Cadence design tool. Optical components fabricated in the IME 130nm SOI CMOS process are characterized. Corresponding compact Verilog-A models for Mach-Zehnder modulator (MZM) device are developed. With this approach, electro-optical co-design and hybrid simulation are made possible. The developed optical models are used for analyzing the system-level specifications of an MZM based optoelectronic transceiver link. Link power budgets for NRZ, PAM-4 and PAM-8 signaling modulations are simulated at system-level. The optimal transmitter extinction ratio (ER) is derived based on the required receiver\u27s minimum optical modulation amplitude (OMA). A limiting receiver is fabricated in the IBM 130 nm CMOS process. By side- by-side wire-bonding to a commercial high-speed InGaAs/InP PIN photodiode, we demonstrate that the hybrid optoelectronic limiting receiver can achieve the bit error rate (BER) of 10-12 with a -6.7 dBm sensitivity at 4 Gb/s. A full-rate, 4-channel 29-1 length parallel PRBS is fabricated in the IBM 130 nm SiGe BiCMOS process. Together with a 10 GHz phase locked loop (PLL) designed from system architecture to transistor level design, the PRBS is demonstrated operating at more than 10 Gb/s. Lessons learned from high-speed PCB design, dealing with signal integrity issue regarding to the PCB transmission line are summarized

Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications

As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well

A PAM-4 VCSEL TRANSMITTER WITH 2.5 TAP NON-LINEAR EQUALIZER IN 65NM CMOS

This thesis presents a Vertical Cavity Surface Emitting Laser (VCSEL) based transmitter that uses a nonlinear equalizer to equalize for nonlinear and bandwidth limited behavior of VCSEL. The transmitter employs PAM4 modulation scheme and a 2.5 tap nonlinear equalizer to maximize the vertical eye opening and reduce the skew in PAM4 eyes resulting from nonlinear behavior. The equalizer can also compensate for the static nonlinearity resulting from finite output impedance of tail current sources and low bandwidth resulting from the large capacitance (parasitic and pad) and large resistance (of VCSEL) at the output node. The nonlinear equalizer reduces to a traditional linear equalizer in cases where VCSEL can be approximated as linear e.g., for high bias currents. For such cases, 2.5 tap equalizer provides performance improvement over traditional 2 tap equalizer due to larger memory. The proposed architecture here implements a 2.5 tap nonlinear equalizer using a look-up-table approach and can equalize for all 32 (4^2.5) rising, falling and non-transitioning edges separately. The proposed architecture also uses a nonuniform DAC in the current mode output driver which utilizes the information related to unused levels and results in improved resolution when compared against the traditionally used uniform DAC. The transmitter consumes a power of 250mW and achieves a data rate of 50Gbps with a power efficiency of 5pJ/bit. The core transmitter area including PRBS, LUT, serializer and output driver is 375um*500um while the total chip area is 1.4mm*1.4mm. The transmitter has been implemented in 65nm CMOS technology