A Biofuel-Cell-Based Energy Harvester With 86% Peak Efficiency and 0.25-V Minimum Input Voltage Using Source-Adaptive MPPT

This article presents an efficient cold-starting energy harvester system, fabricated in 65-nm CMOS. The proposed harvester uses no external electrical components and is compatible with biofuel-cell (BFC) voltage and power ranges. A power-efficient system architecture is proposed to keep the internal circuitry operating at 0.4 V while regulating the output voltage at 1 V using switched-capacitor dc–dc converters and a hysteretic controller. A startup enhancement block is presented to facilitate cold startup with any arbitrary input voltage. A real-time on-chip 2-D maximum power point tracking with source degradation tracing is also implemented to maintain power efficiency maximized over time. The system performs cold startup with a minimum input voltage of 0.39 V and continues its operation if the input voltage degrades to as low as 0.25 V. Peak power efficiency of 86% is achieved at 0.39 V of input voltage and 1.34 μW of output power with 220 nW of average power consumption of the chip. The end-to-end power efficiency is kept above 70% for a wide range of loading powers from 1 to 12 μW. The chip is integrated with a pair of lactate BFC electrodes with 2 mm of diameter on a prototype-printed circuit board (PCB). Integrated operation of the chip with the electrodes and a lactate solution is demonstrated

Single-Chip Isolated DC-DC Converter with Self-Tuned Maximum Power Transfer Frequency

abstract: There is an increasing demand for fully integrated point-of-load (POL) isolated DC-DC converters that can provide an isolation barrier between the primary and the secondary side, while delivering a low ripple, low noise regulated voltage at their isolated sides to a high dynamic range, sensitive mixed signal devices, such as sensors, current-shunt-monitors and ADCs. For these applications, smaller system size and integration level is important because the whole system may need to fit to limited space. Traditional methods for providing isolated power are discrete solutions using bulky transformers. Miniaturization of isolated POL regulators is becoming highly desirable for low power applications. A fully integrated, low noise isolated point-of-load DC-DC converter for supply regulation of high dynamic range analog and mixed signal sensor signal-chains is presented. The isolated DC-DC converter utilizes an integrated planar air-core micro-transformer as a coupled resonator and isolation barrier and enables direct connection of low-voltage mixed signal circuits to higher supply rails. The air core transformer is driven at its primary resonant frequency of 100 MHz to achieve maximum power transfer. A mixed-signal perturb-and-observe based frequency search algorithm is developed to improve maximum power transfer efficiency by 60% across the isolation barrier compared to fixed driving frequency method. The isolated converter’s output ripple is reduced by utilizing spread spectrum clocking in the driver. An isolated PMOS LDO in the secondary side is used to suppress switching noise and ripple by 21dB. Conducted and radiated EMI distribution on the IC is measured by a set of integrated ring oscillator based noise sensors with -68dBm noise sensitivity. The proposed isolated converter achieves highest level of integration with respect to earlier reported integrated isolated converters, while providing 50V on-chip junction isolation without the need for extra silicon post-processing steps.Dissertation/ThesisDoctoral Dissertation Electrical Engineering 201

Efficient and Scalable Computing for Resource-Constrained Cyber-Physical Systems: A Layered Approach

With the evolution of computing and communication technology, cyber-physical systems such as self-driving cars, unmanned aerial vehicles, and mobile cognitive robots are achieving increasing levels of multifunctionality and miniaturization, enabling them to execute versatile tasks in a resource-constrained environment. Therefore, the computing systems that power these resource-constrained cyber-physical systems (RCCPSs) have to achieve high efficiency and scalability. First of all, given a fixed amount of onboard energy, these computing systems should not only be power-efficient but also exhibit sufficiently high performance to gracefully handle complex algorithms for learning-based perception and AI-driven decision-making. Meanwhile, scalability requires that the current computing system and its components can be extended both horizontally, with more resources, and vertically, with emerging advanced technology. To achieve efficient and scalable computing systems in RCCPSs, my research broadly investigates a set of techniques and solutions via a bottom-up layered approach. This layered approach leverages the characteristics of each system layer (e.g., the circuit, architecture, and operating system layers) and their interactions to discover and explore the optimal system tradeoffs among performance, efficiency, and scalability. At the circuit layer, we investigate the benefits of novel power delivery and management schemes enabled by integrated voltage regulators (IVRs). Then, between the circuit and microarchitecture/architecture layers, we present a voltage-stacked power delivery system that offers best-in-class power delivery efficiency for many-core systems. After this, using Graphics Processing Units (GPUs) as a case study, we develop a real-time resource scheduling framework at the architecture and operating system layers for heterogeneous computing platforms with guaranteed task deadlines. Finally, fast dynamic voltage and frequency scaling (DVFS) based power management across the circuit, architecture, and operating system layers is studied through a learning-based hierarchical power management strategy for multi-/many-core systems

A Charge-Recycling Scheme and Ultra Low Voltage Self-Startup Charge Pump for Highly Energy Efficient Mixed Signal Systems-On-A-Chip

The advent of battery operated sensor-based electronic systems has provided a pressing need to design energy-efficient, ultra-low power integrated circuits as a means to improve the battery lifetime. This dissertation describes a scheme to lower the power requirement of a digital circuit through the use of charge-recycling and dynamic supply-voltage scaling techniques. The novel charge-recycling scheme proposed in this research demonstrates the feasibility of operating digital circuits using the charge scavenged from the leakage and dynamic load currents inherent to digital design. The proposed scheme efficiently gathers the “ground-bound” charge into storage capacitor banks. This reclaimed charge is then subsequently recycled to power the source digital circuit. The charge-recycling methodology has been implemented on a 12-bit Gray-code counter operating at frequencies of less than 50 MHz. The circuit has been designed in a 90-nm process and measurement results reveal more than 41% reduction in the average energy consumption of the counter. The total energy savings including the power consumed for the generation of control signals aggregates to an average of 23%. The proposed methodology can be applied to an existing digital path without any design change to the circuit but with only small loss to the performance. Potential applications of this scheme are described, specifically in wide-temperature dynamic power reduction and as a source for energy harvesters. The second part of this dissertation deals with the design and development of a self-starting, ultra-low voltage, switched-capacitor (SC) DC-DC converter that is essential to an energy harvesting system. The proposed charge-pump based SC-converter operates from 125-mV input and thus enables battery-less operation in ultra-low voltage energy harvesters. The charge pump does not require any external components or expensive post-fabrication processing to enable low-voltage operation. This design has been implemented in a 130-nm CMOS process. While the proposed charge pump provides significant efficiency enhancement in energy harvesters, it can also be incorporated within charge recycling systems to facilitate adaptable charge-recycling levels. In total, this dissertation provides key components needed for highly energy-efficient mixed signal systems-on-a-chip

Small Form Factor Hybrid CMOS/GaN Buck Converters for 10W Point of Load Applications

abstract: Point of Load (PoL) converters are important components to the power distribution system in computer power supplies as well as automotive, space, nuclear, and medical electronics. These converters often require high output current capability, low form factor, and high conversion ratios (step-down) without sacrificing converter efficiency. This work presents hybrid silicon/gallium nitride (CMOS/GaN) power converter architectures as a solution for high-current, small form-factor PoL converters. The presented topologies use discrete GaN power devices and CMOS integrated drivers and controller loop. The presented power converters operate in the tens of MHz range to reduce the form factor by reducing the size of the off-chip passive inductor and capacitor. Higher conversion ratio is achieved through a fast control loop and the use of GaN power devices that exhibit low parasitic gate capacitance and minimize pulse swallowing. This work compares three discrete buck power converter architectures: single-stage, multi-phase with 2 phases, and stacked-interleaved, using components-off-the-shelf (COTS). Each of the implemented power converters achieves over 80% peak efficiency with switching speeds up-to 10MHz for high conversion ratio from 24V input to 5V output and maximum load current of 10A. The performance of the three architectures is compared in open loop and closed loop configurations with respect to efficiency, output voltage ripple, and power stage form factor. Additionally, this work presents an integrated CMOS gate driver solution in CMOS 0.35um technology. The CMOS integrated circuit (IC) includes the gate driver and the closed loop controller for directly driving a single-stage GaN architecture. The designed IC efficiently drives the GaN devices up to 20MHz switching speeds. The presented controller technique uses voltage mode control with an innovative cascode driver architecture to allow a 3.3V CMOS devices to effectively drive GaN devices that require 5V gate signal swing. Furthermore, the designed power converter is expected to operate under 400MRad of total dose, thus enabling its use in high-radiation environments for the large hadron collider at CERN and nuclear facilities.Dissertation/ThesisMasters Thesis Electrical Engineering 201

Low-Power Energy Efficient Circuit Techniques for Small IoT Systems

Although the improvement in circuit speed has been limited in recent years, there has been increased focus on the internet of things (IoT) as technology scaling has decreased circuit size, power usage and cost. This trend has led to the development of many small sensor systems with affordable costs and diverse functions, offering people convenient connection with and control over their surroundings. This dissertation discusses the major challenges and their solutions in realizing small IoT systems, focusing on non-digital blocks, such as power converters and analog sensing blocks, which have difficulty in following the traditional scaling trends of digital circuits. To accommodate the limited energy storage and harvesting capacity of small IoT systems, this dissertation presents an energy harvester and voltage regulators with low quiescent power and good efficiency in ultra-low power ranges. Switched-capacitor-based converters with wide-range energy-efficient voltage-controlled oscillators assisted by power-efficient self-oscillating voltage doublers and new cascaded converter topologies for more conversion ratio configurability achieve efficient power conversion down to several nanowatts. To further improve the power efficiency of these systems, analog circuits essential to most wireless IoT systems are also discussed and improved. A capacitance-to-digital sensor interface and a clocked comparator design are improved by their digital-like implementation and operation in phase and frequency domain. Thanks to the removal of large passive elements and complex analog blocks, both designs achieve excellent area reduction while maintaining state-of-art energy efficiencies. Finally, a technique for removing dynamic voltage and temperature variations is presented as smaller circuits in advanced technologies are more vulnerable to these variations. A 2-D simultaneous feedback control using an on-chip oven control locks the supply voltage and temperature of a small on-chip domain and protects circuits in this locked domain from external voltage and temperature changes, demonstrating 0.0066 V/V and 0.013 °C/°C sensitivities to external changes. Simple digital implementation of the sensors and most parts of the control loops allows robust operation within wide voltage and temperature ranges.PHDElectrical EngineeringUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttps://deepblue.lib.umich.edu/bitstream/2027.42/138743/1/wanyeong_1.pd

A fully integrated 2:1 self-oscillating switched-capacitor DC-DC converter in 28 nm UTBB FD-SOI

The importance of energy-constrained processors continues to grow especially for ultra-portable sensor-based platforms for the Internet-of-Things (IoT). Processors for these IoT applications primarily operate at near-threshold (NT) voltages and have multiple power modes. Achieving high conversion efficiency within the DC–DC converter that supplies these processors is critical since energy consumption of the DC–DC/processor system is proportional to the DC–DC converter efficiency. The DC–DC converter must maintain high efficiency over a large load range generated from the multiple power modes of the processor. This paper presents a fully integrated step-down self-oscillating switched-capacitor DC–DC converter that is capable of meeting these challenges. The area of the converter is 0.0104 mm2 and is designed in 28 nm ultra-thin body and buried oxide fully-depleted SOI (UTBB FD-SOI). Back-gate biasing within FD-SOI is utilized to increase the load power range of the converter. With an input of 1 V and output of 460 mV, measurements of the converter show a minimum efficiency of 75% for 79 nW to 200 µW loads. Measurements with an off-chip NT processor load show efficiency up to 86%. The converter’s large load power range and high efficiency make it an excellent fit for energy-constrained processors.</p