Design of Touch Screen Controller IC for Transparent Fingerprint Sensor

Department of Electrical EngineeringA design of system architecture and analog-front-end (AFE) with high SNR and high frame rate for mutual capacitive touch screen with multiple electrodes is presented. Firstly, a differential continuous-mode parallel operation architecture (DCPA) is proposed for large-sized TSP. The proposed architecture achieves a high product of signal-to-noise ratio (SNR) and frame rate, which is a requirement of ROIC for large-sized TSP. DCPA is accomplished by using the proposed differential sensing method with a parallel architecture in a continuous-mode. A continuous-type differential charge amplifier removes the common-mode noise component, and reduces the self-noise by the band-pass filtering effect of the continuous-mode charge amplifier. In addition, the differential parallel architecture cancels the timing skew problem caused by the continuous-mode parallel operation and effectively enhances the power spectrum density of the signal. The proposed ROIC was fabricated using a 0.18-um CMOS process and occupied an active area of 1.25 mm2. The proposed system achieved a 72 dB SNR and 240 Hz frame rate with a 32 channel TX by 10 channel RX mutual capacitive TSP. Moreover, the proposed differential-parallel architecture demonstrated higher immunity to lamp noise and display noise. The proposed system consumed 42.5 mW with a 3.3-V supply. Secondly, readout IC (ROIC) with a differential coded multiple signaling method (DCMS) is proposed to detect an atto-farad capacitance difference for fingerprint recognition in fingerprint TSP. A readout IC with high SNR and fast frame rate are required in the fingerprint recognition. However, the capacitance difference by the ridge and valley of the fingerprint is very small, so that the signal-to-noise ratio is very low. In addition, it takes long time to scan whole fingerprint TSP with multiple electrodes. A fully differential architecture with differential signaling is proposed to detect the low capacitance difference in fingerprint TSP. The internal noise generated is minimized by 2nd fully differential operational amplifier and external noise is eliminated by a lock-in sensing structure. In addition, DCMS reduces an AC offset and enhances a higher product of SNR and frame rate in multiple channels. The proposed architectures can distinguish a 50-atto-farad which is a capacitance difference resulted from the ridges and valley of the finger under the 0.3T glass. The total scan time for 42 ?? 42 fingerprint TSP is less than 21 ms and the power consumption is below 20 mW at 3.3 V supply voltage. IC has been fabricated using a 0.18 ??m standard CMOS process.ope

Design of Analog Front-End of Touch-Screen Controller with Enhanced Noise Immunity and Configurable SNR and Frame Rate

학위논문 (박사)-- 서울대학교 대학원 : 전기·컴퓨터공학부, 2017. 2. 정덕균.A design of analog front-end (AFE) for touch-screen controller (TSC) with highly enhanced noise immunity and configurable signal-to-noise ratio (SNR) and frame rate is proposed. First, the AFE for the mobile TSC is presented, which provides a configurable SNR and frame rate. The AFE configures its SNR and frame rate by adjusting the sampling cycles of the employed ADC. The test chip is fabricated in a 0.18-μm CMOS process and occupies a 2.2-mm2 active area. The test chip achieves 60-dB SNR and 200-Hz frame rate with 12 × 8 TSP. The SNR can be adjusted from 40 to 67 dB, while the frame rate is then inversely scaled from 50 Hz to 6.4 kHz. The test chip consumes 6.26 mW from a 3.3-V supply. The AFE for the tablet TSC is also presented, which provides highly enhanced noise immunity and configurable SNR and frame rate. The proposed AFE provides TX channels of 36 and RX channels of 64 in order to support a large-size TSP. A multi-driving TX structure with frequency-hopping signal generator is employed to improve the SNR and noise immunity. For a suppression of severe noise interference injected through the TSP, the RX sensing block adopts pre-filtering differential sensing method and high-order noise filtering structure. The AFE supports configurable SNR and frame rate with on-chip frame-rate controller. The test chip is fabri-cated in a 0.18-μm CMOS process. The active area of the test chip is 36 mm2. A 12.2-inch TSP with TX channels of 36 and RX channels of 64 is used in the measurement. The test chip achieves 54-dB SNR and 120-Hz frame rate with a finger touch. The frame rate can be adjusted from 85 to 385 Hz. The test chip achieves up to 20-Vpp noise immunity. The test chip consumes 94.5 mW with a 3.3-V supply.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 3 CHAPTER 2 BASIC STUDY ON TOUCH-SCREEN CONTROLLER 5 2.1 TOUCH-SCREEN PANEL 5 2.2 TOUCH-SCREEN CONTROLLER 8 2.2.1 OVERVIEW ON TSC 8 2.3 ANALOG FRONT-END OF TSC 11 2.3.1 PERFORMANCE METRIC 12 2.3.2 DESIGN ISSUES OF AFE 15 CHAPTER 3 AFE OF MOBILE TSC WITH CONFIGURABLE SNR AND FRAME RATE 18 3.1 OVERVIEW 18 3.2 SYSTEM ARCHITECTURE 21 3.3 CONFIGURABLE SNR AND FRAME RATE 23 3.4 MEASUREMENT RESULTS 29 CHAPTER 4 AFE OF TABLET TSC WITH ENHANCED NOISE IMMUNITY 35 4.1 OVERVIEW 35 4.2 DESIGN ISSUES BY LARGE-SIZE TSP 38 4.3 DESIGN ISSUES BY NOISE INTERFERENCE 40 4.3.1 NOISE INTERFERENCE 40 4.3.2 DISPLAY NOISE REJECTION TECHNIQUE 43 4.3.3 CHARGER NOISE FILTERING TECHNIQUE 46 4.3.4 HIGH-VOLTAGE TX TECHNIQUE 50 4.3.5 MULTI-DRIVING TX TECHNIQUE 52 4.4 PROPOSED ARCHITECTURE 66 4.4.1 TX DRIVING ARCHITECTURE 67 4.4.2 RX SENSING ARCHITECTURE 71 4.5 MULTI-DRIVING TX STRUCTURE 75 4.5.1 CONSIDERATIONS FOR TX MODULATION SEQUENCE 75 4.5.2 COMPARISON OF MODULATION SEQUENCES 76 4.5.3 MODIFIED BUSH-TYPE HADAMARD MATRIX 79 4.6 NOISE FILTERING RX 83 4.6.1 PRE-FILTERING DIFFERENTIAL SENSING METHOD 83 4.6.2 NOISE-IMMUNE SENSING STRUCTURE 87 4.6.3 CONFIGURABLE SNR AND FRAME RATE 106 4.6.4 RX MODULATION 112 4.7 CIRCUIT IMPLEMENTATION 120 4.7.1 CHARGE AMPLIFIER AND BAND-PASS FILTER 121 4.7.2 CAPACITIVE DIFFERENTIAL AMPLIFIER 123 4.7.3 MIXER AND RX MODULATION 125 4.7.4 LOW-PASS FILTER 127 4.7.5 INCREMENTAL ΔΣ ADC 128 4.7.6 DIGITAL DEMODULATION 130 4.7.7 TX DRIVING BLOCK 131 4.8 MEASUREMENT RESULTS 132 4.8.1 TOUCH-SCREEN PANEL (TSP) 132 4.8.2 MEASUREMENT ENVIRONMENTS 133 4.8.3 FABRICATED AFE 134 4.8.4 OPERATION OF THE FABRICATED AFE 135 4.8.5 SNR MEASUREMENT 139 4.8.6 CONFIGURABLE SNR AND FRAME RATE 139 4.8.7 NOISE IMMUNITY 141 4.8.8 COMPARISON WITH OTHER WORKS 157 CHAPTER 5 CONCLUSION 158 BIBLIOGRAPHY 160 초 록 170Docto

?????? ?????? ???????????? ?????? ???????????? ??????????????? ?????????????????? ??? ???????????????

Department of Electrical EngineeringA Sensor system is advanced along sensor technologies are developed. The performance improvement of sensor system can be expected by using the internet of things (IoT) communication technology and artificial neural network (ANN) for data processing and computation. Sensors or systems exchanged the data through this wireless connectivity, and various systems and applications are possible to implement by utilizing the advanced technologies. And the collected data is computed using by the ANN and the efficiency of system can be also improved. Gas monitoring system is widely need from the daily life to hazardous workplace. Harmful gas can cause a respiratory disease and some gas include cancer-causing component. Even though it may cause dangerous situation due to explosion. There are various kinds of hazardous gas and its characteristics that effect on human body are different each gas. The optimal design of gas monitoring system is necessary due to each gas has different criteria such as the permissible concentration and exposure time. Therefore, in this thesis, conventional sensor system configuration, operation, and limitation are described and gas monitoring system with wireless connectivity and neural network is proposed to improve the overall efficiency. As I already mentioned above, dangerous concentration and permissible exposure time are different depending on gas types. During the gas monitoring, gas concentration is lower than a permissible level in most of case. Thus, the gas monitoring is enough with low resolution for saving the power consumption in this situation. When detecting the gas, the high-resolution is required for the accurate concentration detecting. If the gas type is varied in the above situation, the amount of calculation increases exponentially. Therefore, in the conventional systems, target specifications are decided by the highest requirement in the whole situation, and it occurs increasing the cost and complexity of readout integrated circuit (ROIC) and system. In order to optimize the specification, the ANN and adaptive ROIC are utilized to compute the complex situation and huge data processing. Thus, gas monitoring system with learning-based algorithm is proposed to improve its efficiency. In order to optimize the operation depending on situation, dual-mode ROIC that monitoring mode and precision mode is implemented. If the present gas concentration is decided to safe, monitoring mode is operated with minimal detecting accuracy for saving the power consumption. The precision mode is switched when the high-resolution or hazardous situation are detected. The additional calibration circuits are necessary for the high-resolution implementation, and it has more power consumption and design complexity. A high-resolution Analog-to-digital converter (ADC) is kind of challenges to design with efficiency way. Therefore, in order to reduce the effective resolution of ADC and power consumption, zooming correlated double sampling (CDS) circuit and prediction successive approximation register (SAR) ADC are proposed for performance optimization into precision mode. A Microelectromechanical systems (MEMS) based gas sensor has high-integration and high sensitivity, but the calibration is needed to improve its low selectivity. Conventionally, principle component analysis (PCA) is used to classify the gas types, but this method has lower accuracy in some case and hard to verify in real-time. Alternatively, ANN is powerful algorithm to accurate sensing through collecting the data and training procedure and it can be verified the gas type and concentration in real-time. ROIC was fabricated in complementary metal-oxide-semiconductor (CMOS) 180-nm process and then the efficiency of the system with adaptive ROIC and ANN algorithm was experimentally verified into gas monitoring system prototype. Also, Bluetooth supports wireless connectivity to PC and mobile and pattern recognition and prediction code for SAR ADC is performed in MATLAB. Real-time gas information is monitored by Android-based application in smartphone. The dual-mode operation, optimization of performance and prediction code are adjusted with microcontroller unit (MCU). Monitoring mode is improved by x2.6 of figure-of-merits (FoM) that compared with previous resistive interface.clos

Polymer-Based Microfluidic Devices for High Throughput Single Molecule Detection: Applications in Biological and Drug Discovery

The realization of high throughput sample processing has become a primary ambition in many research applications with an example being high throughput screening (HTS), which represents the first step in the drug discovery pipeline. Microfluidics is a viable platform for parallel processing of biochemical reactions to increase data production rates due to its ability to generate fluidic networks with a high number of processors over small footprints suitable for optical imaging. Single-molecule detection (SMD) is another technology which has emerged to facilitate the realization of high throughput data processing afforded by its ability to eliminate sample processing steps and generate results with high statistical accuracy. A combination of microfluidics and SMD with wide-field fluorescence detection provides the ability to monitor biochemical reactions in a high throughput format with single-molecule sensitivity. In this dissertation, the integration of these techniques was presented for HTS applications in drug discovery. An ultra-sensitive fluorescence detection system with a wide field-of-view (FoV) was constructed to transduce fluorescence signatures from single chromophores that were electrokinetically transported through a series of tightly packed fluidic channels poised on poly(methylmethacrylate), PMMA and contained within the FoV of a laser detection system. The system was used to monitor biochemical reactions at the single-molecule level in a continuous-flow format. Enhancement in sampling-throughput was demonstrated by constructing a high density fluidic network for parallel analysis of multiple biochemical assays. In another development, the ability to enhance single-molecule sensitivity in a flow-based biochemical assay was investigated using a novel cyclic olefin copolymer (COC) planar waveguide embedded in PMMA and situated orthogonal to multiple fluidic channels. This design allowed for fluorescence detection from multiple fluidic channels using evanescent excitation and a wide FoV fluorescence detection system for parallel readout. Results from these technologies were presented as well as their applications in drug discovery for increasing data production rates and quality. An approach toward monitoring the efficacy of therapeutic agents, which is important in clinical evaluation of drug potency in the drug discovery process, was also considered, by designing a microfluidic system with integrated conductivity sensor for label-free enumeration of isolated tumor cells from clinical samples

Wireless Power Transfer System for Battery-Less Body Implantable Devices

Department of Electrical EngineeringAs the life expectancy is increased and the welfare is promoted, researches on the body implantable medical devices (BIMD) are actively being carried out, and products providing more various functions are being released. On the other hand, due to these various functions, the power consumption of the BIMD is also increased, so that the primary battery alone cannot provide sufficient power for the devices. The limited capacity and life time of batteries force patients to make an additional payment and suffering for the power supply of the BIMD. Wireless power transfer technology is the technology which has been making remarkable progress mainly in wireless charging for personal portable devices and electric vehicles. Convergence of wireless power transfer technology (WPT) and rechargeable battery can extend the life time of the BIMD and reduce the suffering and the cost for battery replacements. Furthermore, WPT enables the devices which do not need to operate consistently such as body implantable sensor devices to be used without batteries. In this dissertation, techniques to support WPT for BIMD are introduced and proposed. First, basic researches on magnetic coupled WPT are presented. The basics which are important factors to analyze power transmission are introduced. In addition, circuits that make up the WPT system are described. There are three common technical challenges in WPT. Those are efficiency degradation on coil geometry, voltage gain variation with coil geometry, and power losses in WPT. The common challenges are discussed in chapter II. Moreover, additional challenges which are arisen in WPT for BIMD and approaches to resolve the challenges are addressed in chapter II. Then, efficiency improvement techniques and control techniques in WPT are presented in chapter III. The presented techniques to improve efficiency are applied in coil parts and circuit parts. In coil parts, efficiency enhancement technique by geometric variation is proposed. In circuit parts, instantaneous power consuming technique for step-down converter is suggested. Li-ion battery charger is also discussed in chapter III. Additionally, the wireless controlled constant current / constant voltage charging mode and the proposed step charging method are described. After that, WPT system for BIMD is discussed one by one with the proposed techniques for each part in chapter IV. A load transformation is suggested to improve efficiency in weak coupling, and suppress voltage gain variation under coil displacement. Power conversion efficiency improvement techniques for rectifier and converter are also proposed. By using the proposed technique for the converter, we can remove the bootstrap capacitors, and reduce the overall size of power circuits. In conclusion, techniques in coil parts and circuit parts to handle challenges in WPT for BIMD are fully investigated in this thesis in addition to the efficiency improvement and control techniques in common WPT. All the techniques are verified through simulations or experiments. The approaches realized in the thesis can be applied to other applications employing the WPT.clos

The First Multichroic Receiver and Results from ACTPol.

The Cosmic Microwave Background (CMB) is a unique and powerful tool for the study of cosmology and fundamental physics. The next frontier of CMB research is to extract the wealth of cosmological information available from its polarization. Accurate measurement of this polarization signal will enable us to probe inflation, provide an alternative means to measure the neutrino mass sum and number of neutrino species; improve our understanding of dark energy; explore the reionization history of our Universe; probe the large scale structure through gravitational lensing; and enable a multitude of other astrophysical studies. The polarized signatures of the early universe are extremely weak, dominated by foregrounds, and its measurement is susceptible to instrumental effects. Extracting the information contained in these faint signals requires instruments with high sensitivity, excellent control over systematic errors, and careful data analysis. The Atacama Cosmology Telescope Polarimeter (ACTPol) is a state-of-the-art experiment that measures CMB polarization over finer angular scales from the Atacama desert in Chile. In this thesis, I present an overview of this project and then describe my work on the project including development of a new polarization sensitive dichroic camera for ACTPol designed to increase the sensitivity of CMB telescopes and enable high precision measurements of CMB polarization; the development of novel metamaterial antireflection coatings for silicon lenses; diffraction from panel gaps; calibration of detector pass-bands; and a detailed description of my analysis of the polarization properties of extragalactic point sources discovered with the ACTPol data. I conclude with a discussion of the science of ACTPol, and the impact of my technical work on future CMB experiments.PHDPhysicsUniversity of Michigan, Horace H. Rackham School of Graduate Studieshttp://deepblue.lib.umich.edu/bitstream/2027.42/135767/1/dattar_1.pd

72 dB SNR, 240 Hz Frame Rate Readout IC With Differential Continuous-Mode Parallel Architecture for Larger Touch-Screen Panel Applications

This paper presents a mutual capacitive touch screen panel (TSP) readout IC (ROIC) with a differential continuousmode parallel operation architecture (DCPA). The proposed architecture achieves a high product of signal-to-noise ratio (SNR) and frame rate, which is a requirement of ROIC for large-sized TSP. DCPA is accomplished by using the proposed differential sensing method with a parallel architecture in a continuousmode. This architecture is implemented using a continuous-type transmitter for parallel signaling and a differential-architecture receiver. A continuous-type differential charge amplifier removes the common-mode noise component, and reduces the self-noise by the band-pass filtering effect of the continuous-mode charge amplifier. In addition, the differential parallel architecture cancels the timing skew problem caused by the continuous-mode parallel operation and effectively enhances the power spectrum density of the signal. The proposed ROIC was fabricated using a 0.18-??m CMOS process and occupied an active area of 1.25 mm2. The proposed system achieved a 72 dB SNR and 240 Hz frame rate with a 32 channel TX by 10 channel RX mutual capacitive TSP. Moreover, the proposed differential-parallel architecture demonstrated higher immunity to lamp noise and display noise. The proposed system consumed 42.5 mW with a 3.3-V supply.clos

Machine Learning in Sensors and Imaging

Machine learning is extending its applications in various fields, such as image processing, the Internet of Things, user interface, big data, manufacturing, management, etc. As data are required to build machine learning networks, sensors are one of the most important technologies. In addition, machine learning networks can contribute to the improvement in sensor performance and the creation of new sensor applications. This Special Issue addresses all types of machine learning applications related to sensors and imaging. It covers computer vision-based control, activity recognition, fuzzy label classification, failure classification, motor temperature estimation, the camera calibration of intelligent vehicles, error detection, color prior model, compressive sensing, wildfire risk assessment, shelf auditing, forest-growing stem volume estimation, road management, image denoising, and touchscreens

MEMS Technology for Biomedical Imaging Applications

Biomedical imaging is the key technique and process to create informative images of the human body or other organic structures for clinical purposes or medical science. Micro-electro-mechanical systems (MEMS) technology has demonstrated enormous potential in biomedical imaging applications due to its outstanding advantages of, for instance, miniaturization, high speed, higher resolution, and convenience of batch fabrication. There are many advancements and breakthroughs developing in the academic community, and there are a few challenges raised accordingly upon the designs, structures, fabrication, integration, and applications of MEMS for all kinds of biomedical imaging. This Special Issue aims to collate and showcase research papers, short commutations, perspectives, and insightful review articles from esteemed colleagues that demonstrate: (1) original works on the topic of MEMS components or devices based on various kinds of mechanisms for biomedical imaging; and (2) new developments and potentials of applying MEMS technology of any kind in biomedical imaging. The objective of this special session is to provide insightful information regarding the technological advancements for the researchers in the community

Development of the Beam Position Monitors for the Diagnostics of the Test Beam Line in the CTF3 at CERN

The work for this thesis is in line with the field of Instrumentation for Particle Accelerators, so called Beam Diagnostics. It is presented the development of a series of electro-mechanical devices called Inductive Pick-Ups (IPU) for Beam Position Monitoring (BPM). A full set of 17 BPM units (16 + 1 spare), named BPS units, were built and installed into the Test Beam Line (TBL), an electron beam decelerator, of the 3rd CLIC Test Facility (CTF3) at CERN ¿European Organization for the Nuclear Research¿. The CTF3, built at CERN by an international collaboration, was meant to demonstrate the technical feasibility of the key concepts for CLIC ¿Compact Linear Collider¿ as a future linear collider based on the novel two-beam acceleration scheme, and in order to achieve the next energy frontier for a lepton collider in theMulti-TeV scale. Modern particle accelerators and in particular future colliders like CLIC requires an extreme alignment and stabilization of the beam in order to enhance its quality, which rely heavily on a beam based alignment techniques. Here the BPMs, like the BPS-IPU, play an important role providing the beam position with precision and high resolution, besides a beam current measurement in the case of the BPS, along the beam lines. The BPS project carried out at IFIC was mainly developed in two phases: prototyping and series production and test for the TBL. In the first project phase two fully functional BPS prototypes were constructed, focusing in this thesis work on the electronic design of the BPS on-board PCBs (Printed Circuit Boards) which are based on transformers for the current sensing and beam position measurement. Furthermore, it is described the monitor mechanical design with emphasis on all the parts directly involved in its electromagnetic functioning, as a result of the coupling of the EM fields generated by the beam with those parts. For that, it was studied its operational parameters, according the TBL specifications, and it was also simulated a new circuital model reproducing the BPS monitor frequency response for its operational bandwidth (1kHz-100MHz). These prototypes were initially tested in the laboratories of the BI-PI section¿Beam Instrumentation - Position and Intensity¿ at CERN. In the second project phase the BPS monitor series, which were built based on the experience acquired during the prototyping phase, the work was focused on the realization of the characterization tests to measure the main operational parameters of each series monitor, for which it was designed and constructed two test benches with different purposes and frequency regions. The first one is designed to work in the low frequency region, between 1kHz-100MHz, in the time scale of the electron beam pulse with a repetition period of 1s and an approximate duration of 140ns. This kind of test setups called Wire Test-bench are commonly used in the accelerators instrumentation field in order to determine the characteristic parameters of a BPM (or pick-up) like its linearity and precision in the position measurement, and also its frequency response (bandwidth). This is done by emulating a low current intensity beam with a stretched wire carrying a current signals which can be precisely positioned with respect the device under test. This test bench was specifically made for the BPS monitor and conceived to perform the measurement data acquisition in an automated way, managing the measurement equipment and the wire positioning motors controller from a PC workstation. Each one of the BPS monitors series were characterized by using this system at the IFIC labs, and the test results and analysis are presented in this work. On the other hand, the high frequency tests, above the X band in the microwave spectrum and at the time scale of the micro-bunch pulses with a bunching period of 83ps (12GHz) inside a long 140ns pulse, were performed in order to measure the longitudinal impedance of the BPS monitor. This must be low enough in order to minimize the perturbations on the beam produced at crossing the monitor, which affects to its stability during the propagation along the line. For that, it was built the high frequency test bench as a coaxial waveguide structure of 24mm diameter matched at 50¿ and with a bandwidth from 18MHz to 30GHz, which was previously simulated, and having room in the middle to place the BPS as the device under test. This high frequency test bench is able to reproduce the TEM (Transversal Electro-Magnetic) propagative modes corresponding to an ultra-relativistic electron beam of 12GHz bunching frequency, so that the Scattering parameters can be measured to obtain the longitudinal impedance of the BPS in the frequency range of interest. Finally, it is also presented the results of the beam test made in the TBL line, with beam currents from 3.5A to 13A (max. available at the moment of the test). In order to determine the minimum resolution attainable by a BPS monitor in the measurement of the beam position, being the device figure of merit, with a resolution goal of 5¿m at maximum beam current of 28A according to the TBL specifications.García Garrigós, JJ. (2013). Development of the Beam Position Monitors for the Diagnostics of the Test Beam Line in the CTF3 at CERN [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/34327TESI