Cancellation of crosstalk-induced jitter

A novel jitter equalization circuit is presented that addresses crosstalk-induced jitter in high-speed serial links. A simple model of electromagnetic coupling demonstrates the generation of crosstalk-induced jitter. The analysis highlights unique aspects of crosstalk-induced jitter that differ from far-end crosstalk. The model is used to predict the crosstalk-induced jitter in 2-PAM and 4-PAM, which is compared to measurement. Furthermore, the model suggests an equalizer that compensates for the data-induced electromagnetic coupling between adjacent links and is suitable for pre- or post-emphasis schemes. The circuits are implemented using 130-nm MOSFETs and operate at 5-10 Gb/s. The results demonstrate reduced deterministic jitter and lower bit-error rate (BER). At 10 Gb/s, the crosstalk-induced jitter equalizer opens the eye at 10^sup-12 BER from 17 to 45 ps and lowers the rms jitter from 8.7 to 6.3 ps

차세대 HBM 용 고집적, 저전력 송수신기 설계

학위논문 (박사) -- 서울대학교 대학원 : 공과대학 전기·정보공학부, 2020. 8. 정덕균.This thesis presents design techniques for high-density power-efficient transceiver for the next-generation high bandwidth memory (HBM). Unlike the other memory interfaces, HBM uses a 3D-stacked package using through-silicon via (TSV) and a silicon interposer. The transceiver for HBM should be able to solve the problems caused by the 3D-stacked package and TSV. At first, a data (DQ) receiver for HBM with a self-tracking loop that tracks a phase skew between DQ and data strobe (DQS) due to a voltage or thermal drift is proposed. The self-tracking loop achieves low power and small area by uti-lizing an analog-assisted baud-rate phase detector. The proposed pulse-to-charge (PC) phase detector (PD) converts the phase skew to a voltage differ-ence and detects the phase skew from the voltage difference. An offset calibra-tion scheme that can compensates for a mismatch of the PD is also proposed. The proposed calibration scheme operates without any additional sensing cir-cuits by taking advantage of the write training of HBM. Fabricated in 65 nm CMOS, the DQ receiver shows a power efficiency of 370 fJ/b at 4.8 Gb/s and occupies 0.0056 mm2. The experimental results show that the DQ receiver op-erates without any performance degradation under a ± 10% supply variation. In a second prototype IC, a high-density transceiver for HBM with a feed-forward-equalizer (FFE)-combined crosstalk (XT) cancellation scheme is pre-sented. To compensate for the XT, the transmitter pre-distorts the amplitude of the FFE output according to the XT. Since the proposed XT cancellation (XTC) scheme reuses the FFE implemented to equalize the channel loss, additional circuits for the XTC is minimized. Thanks to the XTC scheme, a channel pitch can be significantly reduced, allowing for the high channel density. Moreover, the 3D-staggered channel structure removes the ground layer between the verti-cally adjacent channels, which further reduces a cross-sectional area of the channel per lane. The test chip including 6 data lanes is fabricated in 65 nm CMOS technology. The 6-mm channels are implemented on chip to emulate the silicon interposer between the HBM and the processor. The operation of the XTC scheme is verified by simultaneously transmitting 4-Gb/s data to the 6 consecutive channels with 0.5-um pitch and the XTC scheme reduces the XT-induced jitter up to 78 %. The measurement result shows that the transceiver achieves the throughput of 8 Gb/s/um. The transceiver occupies 0.05 mm2 for 6 lanes and consumes 36.6 mW at 6 x 4 Gb/s.본 논문에서는 차세대 HBM을 위한 고집적 저전력 송수신기 설계 방법을 제안한다. 첫 번째로, 전압 및 온도 변화에 의한 데이터와 클럭 간 위상 차이를 보상할 수 있는 자체 추적 루프를 가진 데이터 수신기를 제안한다. 제안하는 자체 추적 루프는 데이터 전송 속도와 같은 속도로 동작하는 위상 검출기를 사용하여 전력 소모와 면적을 줄였다. 또한 메모리의 쓰기 훈련 (write training) 과정을 이용하여 효과적으로 위상 검출기의 오프셋을 보상할 수 있는 방법을 제안한다. 제안하는 데이터 수신기는 65 nm 공정으로 제작되어 4.8 Gb/s에서 370 fJ/b을 소모하였다. 또한 10 % 의 전압 변화에 대하여 안정적으로 동작하는 것을 확인하였다. 두 번째로, 피드 포워드 이퀄라이저와 결합된 크로스 토크 보상 방식을 활용한 고집적 송수신기를 제안한다. 제안하는 송신기는 크로스 토크 크기에 해당하는 만큼 송신기 출력을 왜곡하여 크로스 토크를 보상한다. 제안하는 크로스 토크 보상 방식은 채널 손실을 보상하기 위해 구현된 피드 포워드 이퀄라이저를 재활용함으로써 추가적인 회로를 최소화한다. 제안하는 송수신기는 크로스 토크가 보상 가능하기 때문에, 채널 간격을 크게 줄여 고집적 통신을 구현하였다. 또한 집적도를 더 증가시키기 위해 세로로 인접한 채널 사이의 차폐 층을 제거한 적층 채널 구조를 제안한다. 6개의 송수신기를 포함한 프로토타입 칩은 65 nm 공정으로 제작되었다. HBM과 프로세서 사이의 silicon interposer channel 을 모사하기 위한 6 mm 의 채널이 칩 위에 구현되었다. 제안하는 크로스 토크 보상 방식은 0.5 um 간격의 6개의 인접한 채널에 동시에 데이터를 전송하여 검증되었으며, 크로스 토크로 인한 지터를 최대 78 % 감소시켰다. 제안하는 송수신기는 8 Gb/s/um 의 처리량을 가지며 6 개의 송수신기가 총 36.6 mW의 전력을 소모하였다.CHAPTER 1 INTRODUCTION 1 1.1 MOTIVATION 1 1.2 THESIS ORGANIZATION 4 CHAPTER 2 BACKGROUND ON HIGH-BANDWIDTH MEMORY 6 2.1 OVERVIEW 6 2.2 TRANSCEIVER ARCHITECTURE 10 2.3 READ/WRITE OPERATION 15 2.3.1 READ OPERATION 15 2.3.2 WRITE OPERATION 19 CHAPTER 3 BACKGROUNDS ON COUPLED WIRES 21 3.1 GENERALIZED MODEL 21 3.2 EFFECT OF CROSSTALK 26 CHAPTER 4 DQ RECEIVER WITH BAUD-RATE SELF-TRACKING LOOP 29 4.1 OVERVIEW 29 4.2 FEATURES OF DQ RECEIVER FOR HBM 33 4.3 PROPOSED PULSE-TO-CHARGE PHASE DETECTOR 35 4.3.1 OPERATION OF PULSE-TO-CHARGE PHASE DETECTOR 35 4.3.2 OFFSET CALIBRATION 37 4.3.3 OPERATION SEQUENCE 39 4.4 CIRCUIT IMPLEMENTATION 42 4.5 MEASUREMENT RESULT 46 CHAPTER 5 HIGH-DENSITY TRANSCEIVER FOR HBM WITH 3D-STAGGERED CHANNEL AND CROSSTALK CANCELLATION SCHEME 57 5.1 OVERVIEW 57 5.2 PROPOSED 3D-STAGGERED CHANNEL 61 5.2.1 IMPLEMENTATION OF 3D-STAGGERED CHANNEL 61 5.2.2 CHANNEL CHARACTERISTICS AND MODELING 66 5.3 PROPOSED FEED-FORWARD-EQUALIZER-COMBINED CROSSTALK CANCELLATION SCHEME 72 5.4 CIRCUIT IMPLEMENTATION 77 5.4.1 OVERALL ARCHITECTURE 77 5.4.2 TRANSMITTER WITH FFE-COMBINED XTC 79 5.4.3 RECEIVER 81 5.5 MEASUREMENT RESULT 82 CHAPTER 6 CONCLUSION 93 BIBLIOGRAPHY 95 초 록 102Docto

Space Division Multiplexing in Optical Fibres

Optical communications technology has made enormous and steady progress for several decades, providing the key resource in our increasingly information-driven society and economy. Much of this progress has been in finding innovative ways to increase the data carrying capacity of a single optical fibre. In this search, researchers have explored (and close to maximally exploited) every available degree of freedom, and even commercial systems now utilize multiplexing in time, wavelength, polarization, and phase to speed more information through the fibre infrastructure. Conspicuously, one potentially enormous source of improvement has however been left untapped in these systems: fibres can easily support hundreds of spatial modes, but today's commercial systems (single-mode or multi-mode) make no attempt to use these as parallel channels for independent signals.Comment: to appear in Nature Photonic

Linearization techniques to suppress optical nonlinearity

This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.This thesis is shown the implementation of the linearization techniques such as feedforward and pre-distortion feedback linearization to suppress the optical components nonlinearities caused by the fibre and semiconductor optical amplifier (SOA). The simulation verified these two linearization techniques for single tone direct modulation, two tone indirect modulation and ultra wideband input to the optical fibre. These techniques uses the amplified spontaneously emission (ASE) noise reduction in two loops of SOA by a feed-forward and predistortion linearizer and is shown more than 6dB improvement. Also it investigates linearization for the SOA amplifier to cancel out the third order harmonics or inter-modulation distortion (IMD) or four waves mixing. In this project, more than 20 dB reductions is seen in the spectral re-growth caused by the SOA. Amplifier non-linearity becomes more severe with two strong input channels leading to inter-channel distortion which can completely mask a third adjacent channel. The simulations detailed above were performed utilizing optimum settings for the variable gain, phase and delay components in the error correction loop of the feed forward and Predistortion systems and hence represent the ideal situation of a perfect feed-forward and Predistortion system. Therefore it should be consider that complexity of circuit will increase due to amplitude, phase and delay mismatches in practical design. Also it has describe the compatibility of Software Defined Radio with Hybrid Fibre Radio with simulation model of wired optical networks to be used for future research investigation, based on the star and ring topologies for different modulation schemes, and providing the performance for these configurations

Design Techniques for High Performance Serial Link Transceivers

Increasing data rates over electrical channels with significant frequency-dependent loss is difficult due to excessive inter-symbol interference (ISI). In order to achieve sufficient link margins at high rates, I/O system designers implement equalization in the transmitters and are motivated to consider more spectrally-efficient modulation formats relative to the common PAM-2 scheme, such as PAM-4 and duobinary. The first work, reviews when to consider PAM-4 and duobinary formats, as the modulation scheme which yields the highest system margins at a given data rate is a function of the channel loss profile, and presents a 20Gb/s triple-mode transmitter capable of efficiently implementing these three modulation schemes and three-tap feedforward equalization. A statistical link modeling tool, which models ISI, crosstalk, random noise, and timing jitter, is developed to compare the three common modulation formats operating on electrical backplane channel models. In order to improve duobinary modulation efficiency, a low-power quarter-rate duobinary precoder circuit is proposed which provides significant timing margin improvement relative to full-rate precoders. Also as serial I/O data rates scale above 10 Gb/s, crosstalk between neighboring channels degrades system bit-error rate (BER) performance. The next work presents receive-side circuitry which merges the cancellation of both near-end and far-end crosstalk (NEXT/FEXT) and can automatically adapt to different channel environments and variations in process, voltage, and temperature. NEXT cancellation is realized with a novel 3-tap FIR filter which combines two traditional FIR filter taps and a continuous-time band-pass filter IIR tap for efficient crosstalk cancellation, with all filter tap coefficients automatically determined via an ondie sign-sign least-mean-square (SS-LMS) adaptation engine. FEXT cancellation is realized by coupling the aggressor signal through a differentiator circuit whose gain is automatically adjusted with a power-detection-based adaptation loop. In conclusion, the proposed architectures in the transmitter side and receiver side together are to be good solution in the high speed I/O serial links to improve the performance by overcome the physical channel loss and adjacent channel noise as the system becomes complicated

Crosstalk-induced jitter equalization

A novel jitter equalization circuit is presented that addresses crosstalk-induced jitter in high-speed communication links. A simplified model of electromagnetic coupling demonstrates the generation of crosstalk-induced jitter. This model suggests an equalizer that compensates for the data-induced electromagnetic coupling between adjacent links. Additionally, a data-dependent jitter equalizer that provides separate adjustments of rising and falling edge deviations is presented. The circuits are implemented using 130 nm MOSFETs and operate at 5-10Gb/s. The results demonstrate reduced deterministic jitter and lower bit-error rate. At 10Gb/s, the crosstalk-induced jitter equalizer opens the eye at BER of 10^(-12) from 17ps to 45ps

Design of Energy-Efficient A/D Converters with Partial Embedded Equalization for High-Speed Wireline Receiver Applications

As the data rates of wireline communication links increases, channel impairments such as skin effect, dielectric loss, fiber dispersion, reflections and cross-talk become more pronounced. This warrants more interest in analog-to-digital converter (ADC)-based serial link receivers, as they allow for more complex and flexible back-end digital signal processing (DSP) relative to binary or mixed-signal receivers. Utilizing this back-end DSP allows for complex digital equalization and more bandwidth-efficient modulation schemes, while also displaying reduced process/voltage/temperature (PVT) sensitivity. Furthermore, these architectures offer straightforward design translation and can directly leverage the area and power scaling offered by new CMOS technology nodes. However, the power consumption of the ADC front-end and subsequent digital signal processing is a major issue. Embedding partial equalization inside the front-end ADC can potentially result in lowering the complexity of back-end DSP and/or decreasing the ADC resolution requirement, which results in a more energy-effcient receiver. This dissertation presents efficient implementations for multi-GS/s time-interleaved ADCs with partial embedded equalization. First prototype details a 6b 1.6GS/s ADC with a novel embedded redundant-cycle 1-tap DFE structure in 90nm CMOS. The other two prototypes explain more complex 6b 10GS/s ADCs with efficiently embedded feed-forward equalization (FFE) and decision feedback equalization (DFE) in 65nm CMOS. Leveraging a time-interleaved successive approximation ADC architecture, new structures for embedded DFE and FFE are proposed with low power/area overhead. Measurement results over FR4 channels verify the effectiveness of proposed embedded equalization schemes. The comparison of fabricated prototypes against state-of-the-art general-purpose ADCs at similar speed/resolution range shows comparable performances, while the proposed architectures include embedded equalization as well

Point-to-point advanced self-coherent 200 Gb/s multicore fiber links supported by neural networks

Este trabalho propõe um sistema de fibra multi-núcleo (MCF) de curto alcance de 200 Gb/s considerando lasers reais com ruído de fase (LPN) e recetores Kramers Kronig. Os lasers usados neste sistema consideram larguras de linha típicas de lasers de cavidade externa (ECL) e lasers de feedback distribuído (DFB). Uma rede neural feed-forward (FFNN) é implementada para mitigar os efeitos do LPN e da diafonia entre núcleos (ICXT). O objetivo principal deste trabalho é avaliar o impacto do LPN na melhoria de desempenho proporcionada pela FFNN proposta. Em primeiro lugar, um sistema sem LPN é estudado como referência. Posteriormente, o LPN é introduzido no sistema, com o sinal ótico injetado no núcleo interferente a considerar um laser com largura de linha típica de ECLs e lasers DFB. O sinal ótico injetado no núcleo interferido considera um laser ideal sem LPN. Concluiu-se que, aplicando a FFNN, o BER médio obtido com o ECL e o laser DFB, em comparação com o caso de referência, aumentou mais de uma ordem de grandeza. O BER médio obtido com ambos os lasers manteve-se abaixo do limite de BER quando o intervalo de tempo entre a fase de treino e uso da FFNN (ΔT) não excedeu 20% do tempo de coerência (Tc). Considerando ΔT/Tc=0.1, a FFNN proporcionou uma melhoria de 25% e 22% na probabilidade de indisponibilidade em comparação com a probabilidade de indisponibilidade antes da FFNN, ao considerar um ECL e um laser DFB, respetivamente. Essa melhoria diminui com o aumento de ΔT/Tc.This work proposes a 200 Gb/s short-reach multi-core fiber (MCF) system considering real lasers with laser phase noise (LPN) and Kramers Kronig receivers. The lasers employed in this system consider linewidths typical of external cavity lasers (ECL) and distributed feedback lasers (DFB). A feed-forward neural network (FFNN) is implemented to mitigate the effects of the LPN and inter-core crosstalk (ICXT). The main objective of this work is to assess the impact of the LPN on the performance improvement provided by the proposed FFNN. Firstly, a system without LPN is studied as reference. Afterwards, the LPN is introduced in the system as the optical signal injected in the interfering core considered a laser with linewidth typical of ECLs and DFB lasers. The optical signal injected in the interfered core considered an ideal laser without LPN. It was concluded that, when employing the FFNN, the mean BER obtained with the ECL and DFB laser, compared to the reference case, increased more than one order of magnitude. Furthermore, the mean BER obtained with both lasers was kept below the BER threshold when the time interval between the training phase and the use of the FFNN (ΔT) did not exceed 20% of the coherence time (Tc). Considering ΔT/Tc=0.1, the FFNN provided a 25% and a 22% improvement on the outage probability when compared with the outage probability before the FFNN, while considering an ECL and a DFB laser, respectively. This improvement will decrease with the increase of the ΔT/Tc