Transistor-Level Synthesis of Pipeline Analog-to-Digital Converters Using a Design-Space Reduction Algorithm

A novel transistor-level synthesis procedure for pipeline ADCs is presented. This procedure is able to directly map high-level converter specifications onto transistor sizes and biasing conditions. It is based on the combination of behavioral models for performance evaluation, optimization routines to minimize the power and area consumption of the circuit solution, and an algorithm to efficiently constraint the converter design space. This algorithm precludes the cost of lengthy bottom-up verifications and speeds up the synthesis task. The approach is herein demonstrated via the design of a 0.13 μm CMOS 10 bits@60 MS/s pipeline ADC with energy consumption per conversion of only 0.54 pJ@1 MHz, making it one of the most energy-efficient 10-bit video-rate pipeline ADCs reported to date. The computational cost of this design is of only 25 min of CPU time, and includes the evaluation of 13 different pipeline architectures potentially feasible for the targeted specifications. The optimum design derived from the synthesis procedure has been fine tuned to support PVT variations, laid out together with other auxiliary blocks, and fabricated. The experimental results show a power consumption of 23 [email protected] V and an effective resolution of 9.47-bit@1 MHz. Bearing in mind that no specific power reduction strategy has been applied; the mentioned results confirm the reliability of the proposed approach.Ministerio de Ciencia e Innovación TEC2009-08447Junta de Andalucía TIC-0281

Noise shaping Asynchronous SAR ADC based time to digital converter

Time-to-digital converters (TDCs) are key elements for the digitization of timing information in modern mixed-signal circuits such as digital PLLs, DLLs, ADCs, and on-chip jitter-monitoring circuits. Especially, high-resolution TDCs are increasingly employed in on-chip timing tests, such as jitter and clock skew measurements, as advanced fabrication technologies allow fine on-chip time resolutions. Its main purpose is to quantize the time interval of a pulse signal or the time interval between the rising edges of two clock signals. Similarly to ADCs, the performance of TDCs are also primarily characterized by Resolution, Sampling Rate, FOM, SNDR, Dynamic Range and DNL/INL. This work proposes and demonstrates 2nd order noise shaping Asynchronous SAR ADC based TDC architecture with highest resolution of 0.25 ps among current state of art designs with respect to post-layout simulation results. This circuit is a combination of low power/High Resolution 2nd Order Noise Shaped Asynchronous SAR ADC backend with simple Time to Amplitude converter (TAC) front-end and is implemented in 40nm CMOS technology. Additionally, special emphasis is given on the discussion on various current state of art TDC architectures.Electrical and Computer Engineerin

Design of pixel-level ADCs for energy-sensitive hybrid pixel detectors

Single-photon counting hybrid pixel detectors have shown\ud to be a valid alternative to other types of X-ray imaging\ud devices due to their high sensitivity, low noise, linear behavior\ud and wide dynamic range. One important advantage of these\ud devices is the fact that detector and readout electronics are\ud manufactured separately. This allows the use of industrial\ud state-of-the-art CMOS processes to make the readout\ud electronics, combined with a free choice of detector material\ud (high resistivity Silicon, GaAs or other). By measuring not\ud only the number of X-ray photons but also their energies (or\ud wavelengths), the information content of the image increases,\ud given the same X-ray dose. We have studied several\ud possibilities of adding energy sensitivity to the single photon\ud counting capability of hybrid pixel detectors, by means of\ud pixel-level analog-to-digital converters. We show the results of\ud simulating different kinds of analog-to-digital converters in\ud terms of power, area and speed

Towards a single-photon energy-sensitive pixel readout chip: pixel level ADCs and digital readout circuitry

Unlike conventional CMOS imaging, a single\ud photon imager detects each individual photon impinging on\ud a detector, accumulating the number of photons during a\ud certain time window and not the charge generated by the all\ud the photons hitting the detector during said time window.\ud The latest developments in the semiconductor industry\ud are allowing faster and more complex chips to be designed\ud and manufactured. With these developments in mind we are\ud working towards the next step in single photon X-ray imaging:\ud energy sensitive pixel readout chips. The goal is not only\ud to detect and count individual photons, but also to measure\ud the charge deposited in the detector by each photon, and\ud consequently determine its energy. Basically, we are aiming\ud at a spectrometer-in-a-pixel, or a “color X-ray camera”.\ud The approach we have followed towards this goal is the\ud design of small analog-to-digital-converters at the pixel level,\ud together with a very fast digital readout from the pixels to\ud the periphery of the chip, where the data will be transmitted\ud off-chip.\ud We will present here the design and measurement on prototype\ud chips of two different 4-bit pixel level ADCs. The\ud ADCs are optimized for very small area and low power, with\ud a resolution of 4-bits and a sample rate of 1 Msample/s. The\ud readout architecture is based around current-mode sense\ud amplifiers and asynchronous token-passing between the pixels.\ud This is done in order to achieve event-by-event readout\ud and, consequently, on-line imaging. We need to read eventby-\ud event (photon-by-photon), because we cannot have memory\ud on the pixels due to obvious size constraints. We use\ud current-mode sense amplifiers because they perform very\ud well in similar applications as very fast static-RAM readout

Analogue to Digital and Digital to Analogue Converters (ADCs and DACs): A Review Update

This is a review paper updated from that presented for CAS 2004. Essentially, since then, commercial components have continued to extend their performance boundaries but the basic building blocks and the techniques for choosing the best device and implementing it in a design have not changed. Analogue to digital and digital to analogue converters are crucial components in the continued drive to replace analogue circuitry with more controllable and less costly digital processing. This paper discusses the technologies available to perform in the likely measurement and control applications that arise within accelerators. It covers much of the terminology and 'specmanship' together with an application-oriented analysis of the realisable performance of the various types. Finally, some hints and warnings on system integration problems are given.Comment: 15 pages, contribution to the 2014 CAS - CERN Accelerator School: Power Converters, Baden, Switzerland, 7-14 May 201

Simulation-based high-level synthesis of Nyquist-rate data converters using MATLAB/SIMULINK

This paper presents a toolbox for the simulation, optimization and high-level synthesis of Nyquist-rate Analog-to-Digital (A/D) and Digital-to-Analog (D/A) Converters in MATLAB®. The embedded simulator uses SIMULINK® C-coded S-functions to model all required subcircuits including their main error mechanisms. This approach allows to drastically speed up the simulation CPU-time up to 2 orders of magnitude as compared with previous approaches - based on the use of SIMULINK® elementary blocks. Moreover, S-functions are more suitable for implementing a more detailed description of the circuit. For all subcircuits, the accuracy of the behavioral models has been verified by electrical simulation using HSPICE. For synthesis purposes, the simulator is used for performance evaluation and combined with an hybrid optimizer for design parameter selection. The optimizer combines adaptive statistical optimization algorithm inspired in simulated annealing with a design-oriented formulation of the cost function. It has been integrated in the MATLAB/SIMULINK® platform by using the MATLAB® engine library, so that the optimization core runs in background while MATLAB® acts as a computation engine. The implementation on the MATLAB® platform brings numerous advantages in terms of signal processing, high flexibility for tool expansion and simulation with other electronic subsystems. Additionally, the presented toolbox comprises a friendly graphical user interface to allow the designer to browse through all steps of the simulation, synthesis and post-processing of results. In order to illustrate the capabilities of the toolbox, a 0.13)im CMOS 12bit@80MS/s analog front-end for broadband power line communications, made up of a pipeline ADC and a current steering DAC, is synthesized and high-level sized. Different experiments show the effectiveness of the proposed methodology.Ministerio de Ciencia y Tecnología TIC2003-02355RAICONI