Study of novel Love mode surface acoustic wave filters

Novel Love mode filters based on ZnO and SiO<sub>2</sub>/90° rotated ST-cut quartz crystal structure were fabricated. A comprehensive study was carried out to show the capabilities of such filters. The periodicity of the fingers is 50 μm and the thickness of the SiO<sub>2</sub> and ZnO layers ranges from 0.2 to 7.2 μm. Electromechanical coupling coefficient, capacitance per unit wavelengths of finger pairs and temperature coefficient of frequency are studied in terms of thickness of the wave-guiding layers

Love mode SAW sensors with ZnO layer operating in gas and liquid media

Novel layered surface acoustic wave (SAW) sensors, based on a ZnO/90° rotated ST-cut quartz crystal structure, were fabricated. They were employed for liquid and gas sensing applications. Their mass detection limit in liquid media is as low as 100 pg/cm2. Furthermore, these sensors are able to sense oxygen gas concentrations as low as 0.2 ppm in nitrogen gas

A room temperature polyaniline nanofibre hydrogen gas sensor

Electro-conductive polyaniline (PANI) nanofiber based surface acoustic wave (SAW) gas sensors have been investigated with hydrogen (H 2) gas. A template-free, rapidly mixed method was employed to synthesize polyaniline nanofibers using chemical oxidative polymerization of aniline. The nanofibers were deposited onto a layered ZnO/64° YX LiNbO3 SAW transducer for gas sensing applications. The novel sensor was exposed to various concentrations of H2 gas at room temperature. The sensor response, defined as the relative variation in operating frequency of oscillation due to the introduction of the gas, was 3.04 kHz towards a 1% H2 concentration. A relatively fast response time of 8 sec and a recovery time of 60 sec with good repeatability were observed at room temperature. Due to room temperature operation, the novel gas sensor is promising for environmental and industrial applications

Characterization and testing of Pt/TiO2/SiC thin film layered structure for gas sensing

n/

Nanostructured molybdenum oxide gas sensors

In this paper, we present a surface acoustic wave (SAW) gas sensor based on nano-structured molybdenum oxide (MoOx) thin film. The film was deposited onto a 36° YX LiTaO3 SAW transducer, with an operating frequency of approximately 103 MHz, by thermal evaporation. The nanostructured MoOx film consists of connected nanorods with diameters of less than 100 nm. We compared devices with MoOx deposited by RF sputtering and thermal evaporation and found those with evaporated films have response that are an order of magnitude larger

A room temperature polyaniline nanofiber hydrogen gas sensor

Abstract—Electro-conductive polyaniline (PANI) nanofiber based Surface Acoustic Wave (SAW) gas sensors have been investigated with hydrogen (H2) gas. A template-free, rapidly mixed method was employed to synthesize polyaniline nanofibers using chemical oxidative polymerization of aniline. The nanofibers were deposited onto a layered ZnO/64º YX LiNbO3 SAW transducer for gas sensing applications. The novel sensor was exposed to various concentrations of H2 gas at room temperature. The sensor response, defined as the relative variation in operating frequency of oscillation due to the introduction of the gas, was 3.04 kHz towards a 1 % H2 concentration. A relatively fast response time of 8 sec and a recovery time of 60 sec with good repeatability were observed at room temperature. Due to room temperature operation, the novel gas sensor is promising for environmental and industrial applications. I

Structure and Transport in Coatings from Multiscale Computed Tomography of Coatings-New Perspectives for Eelectrochemical Impedance Spectroscopy Modeling?

Computed Tomography (CT) is an approach that has been extensively applied in many areas of science from understanding structures in living organisms to materials science. In materials science, the study of structures within coatings presents challenges on at least two different levels. First, the structure of the coatings needs to be understood from the atomic scale, where dissolution reactions begin, up to length scales which cover the aggregation of inhibitors and other additives, which take place at ∼10−5 m, i.e. 4 to 5 orders of magnitude. CT is a favourable imaging technique since it allows multiscale information to be obtained non-destructively down to tens of nanometres. In this study X-ray absorption contrast imaging has been used to examine structures created using strontium chromate (SrCrO4) particles embedded in an epoxy film. It has been found that SrCrO4 particles can form clusters that extend a few hundred microns in the plane of the film, span the thickness of the film and have fractal characteristics. There are also volumes of low density epoxy of similar sizes and characteristics to the SrCrO4 clusters. The SrCrO4 clusters have a strong influence on the leaching behaviour since the release changes with time. Initially, leaching is controlled by direct dissolution but, as the clusters dissolve, the release is dominated by the fractal dimension of the cluster. The dissolved clusters leave behind voids filled with electrolyte that provide alternative transport pathways for corrosive ions through the polymer. In this paper, the nature of these clusters will be reviewed and the implication for transport properties and electrochemical assessment will be explored

Investigation of the Carbon Monoxide Gas Sensing Characteristics of Tin Oxide Mixed Cerium Oxide Thin Films

Thin films of tin oxide mixed cerium oxide were grown on unheated substrates by physical vapor deposition. The films were annealed in air at 500 °C for two hours, and were characterized using X-ray photoelectron spectroscopy, atomic force microscopy and optical spectrophotometry. X-ray photoelectron spectroscopy and atomic force microscopy results reveal that the films were highly porous and porosity of our films was found to be in the range of 11.6–21.7%. The films were investigated for the detection of carbon monoxide, and were found to be highly sensitive. We found that 430 °C was the optimum operating temperature for sensing CO gas at concentrations as low as 5 ppm. Our sensors exhibited fast response and recovery times of 26 s and 30 s, respectively

The SsgA-like proteins in actinomycetes: small proteins up to a big task

Several unique protein families have been identified that play a role in the control of developmental cell division in streptomycetes. The SsgA-like proteins or SALPs, of which streptomycetes typically have at least five paralogues, control specific steps of sporulation-specific cell division in streptomycetes, affecting cell wall-related events such as septum localization and synthesis, thickening of the spore wall and autolytic spore separation. The expression level of SsgA, the best studied SALP, has a rather dramatic effect on septation and on hyphal morphology, which is not only of relevance for our understanding of (developmental) cell division but has also been succesfully applied in industrial fermentation, to improve growth and production of filamentous actinomycetes. Recent observations suggest that SsgB most likely is the archetypal SALP, with only SsgB orthologues occurring in all morphologically complex actinomycetes. Here we review 10 years of research on the SsgA-like proteins in actinomycetes and discuss the most interesting regulatory, functional, phylogenetic and applied aspects of this relatively unknown protein family