203 research outputs found
Pickering emulsions stabilized by stacked catanionic micro-crystals controlled by charge regulation
Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG geförderten) Allianz- bzw. Nationallizenz frei zugänglich.This publication is with permission of the rights owner freely accessible due to an Alliance licence and a national licence (funded by the DFG, German Research Foundation) respectively.In this paper the mechanism behind the stabilization of Pickering emulsions by stacked catanionic micro-crystals is described. A temperature-quench of mixtures of oppositely charged surfactants (catanionics) and tetradecane from above the chain melting temperature to room temperature produces stable oil-in-water (o/w) Pickering emulsions in the absence of Ostwald ripening. The oil droplets are decorated by stacks of crystalline discs. The stacking of these discs is controlled by charge regulation as derived from conductivity, scattering and zeta potential measurements. Catanionic nanodiscs are ideal solid particles to stabilize Pickering emulsions since they present no density difference and a structural surface charge which is controlled by the molar ratio between anionic and cationic components. The contact angle of catanionic nanodiscs at a water/oil interface is also controlled by the non-stoichiometry of the components. The resulting energy of adhesion and the repulsion between droplets is much larger than kT. As a consequence of these unique properties of nanodiscs, this type of emulsions presents an extremely high resistance towards coalescence and creaming, even in the presence of salt
Improving sensitivity of a small angle x-ray scattering camera with pinhole collimation using separated optical elements
International audienceWe show that a significant improvement in the sensitivity of a Huxley–Holmes design for a small angle x-ray scattering camera is obtained by separating the mirror and the monochromator. The design of the camera involves a long x-ray mirror close to a point x-ray source associated with a curved focusing crystal located close to the sample. The sample area is located at half the distance between the source and detector planes. Diffuse scattering produced by the mirror is not incident on the focusing crystal, thus reducing the background signal. Complete elimination of hard x rays allows precise calibration and hence absolute determination of sample cross section by means of a semitransparent beam stop. In pinhole geometry, the flux corresponds to a ;107 photons/s through the sample, collimated to 1022 Å21 in q range. This allows determination of scattered intensities on the order of 1023 cm21, corresponding to the scattering related to isothermal compressibility of less than 0.1 mm of pure water. As a reference sample, the widely used Lupolen™, a semicrystalline polymer, is calibrated. The high-q limit (q'4.5 nm21) of a porous calcite sample can be used as a secondary standard for specific area determination of solid/solid or solid–liquid dispersions
Understanding solubilisation using principles of surfactant self-assembly as geometrical constraints
Glycolipid self-assembly: micellar structure
Small-angle scattering is used to investigate a typical glycolipid micelle structure in conjunction with NMR determination of sugar cycle conformation. It is shown that the ellipsoidal shape of the micelle originates from two constraints: sugar rings perpendicular to the interface induce a limited area at the chain-head interface. Together with the bulky hydrated heads, this imposes an ellipsoidal shape
Molecular mechanisms induced by phase modifiers used in hydrometallurgy: consequences on transfer efficiency and process safety
It is a matter of strategic independence for many countries to urgently find processes that take into account environmental and economic issues when recycling critical metals. Liquid–liquid (L/L) extraction is a promising method for recovering rare-earth elements from electrical and electronic waste. However, an optimized process on an industrial scale has not yet been established. One of the main reasons is the lack of fundamental knowledge. Therefore, designing a cost-effective and adaptive formulation is still beyond the scope of possibilities. This requires deciphering the molecular forces that control ion transfer beyond the classical supramolecular complexation and developing predictive models compatible with the design and control needs of recycling processes. In all liquid/liquid processes, the high loading of the organic solvent with metal salts/acids or extractant can sometimes lead to a third phase formation. Phase modifiers are often added to the solvent phase in order to prevent the formation of this third phase. However, the effect of these additives on the extraction efficiency as well as their mechanisms of action are still poorly understood. The phase modifiers used in industrial processes are mainly fatty alcohols, called “lipotropes”. In this paper, we study a new class of molecules opening new possibilities beyond the commonly used phase modifiers (i.e., n-octanol). These are the “hydrotropic” molecules. We first show the role of a model hydrotrope (PnP) in preventing the third phase formation for different extraction systems. We also show that the role of modifiers can be understood according to three molecular mechanisms: as co-solvent, as co-surfactant and by preferential solvation. The dominant molecular effect can be identified and quantified by combining surface tension and neutron scattering experiments. In the case of phase modifiers that are hydrotropes, the co-solvent or co-surfactant effect is dominant. In the case of “lipotropes”, the preferential solvation mechanism is emphasized. Finally, the consequences of these mechanisms on the extraction efficiency and selectivity are discussed
- …