A New Archaeoastronomical Investigation of the Irish Axial-Stone Circles

This paper presents the preliminary results of a project undertaken in 1994 to investigate the astronomical potential of the axial-stone circles (ASCs) of seven or more stones in Counties Cork and Kerry, south-west Ireland. This group of sites is of particular interest in that the monuments in the group bear a striking resemblance to the recumbent stone circles (RSCs) of Aberdeenshire, eastern Scotland, which appear to exhibit a strong pattern of alignment in relation to prominent hilltop summits and the rising and setting position of the moon. The first indications from the Irish data are that similar patterns of alignment are not evident in the Irish ASCs. The Irish sites show no preference for orientation upon prominent hilltops and no clear astronomical trends

Creep Behavior in Interlaminar Shear of a Hi-Nicalon™/SiC-B4C Composite at 1200°C in Air and in Steam

Creep behavior in interlaminar shear of a non-oxide ceramic composite with a multilayered matrix was investigated at 1200∘C in laboratory air and in steam environment. The composite was produced via chemical vapor infiltration (CVI). The composite had an oxidation inhibited matrix, which consisted of alternating layers of silicon carbide and boron carbide and was reinforced with laminated Hi-NicalonTM fibers woven in a five-harness-satin weave. Fiber preforms had pyrolytic carbon fiber coating with boron carbon overlay applied. The interlaminar shear properties were measured. The creep behavior was examined for interlaminar shear stresses in the 16–22 MPa range. Primary and secondary creep regimes were observed in all tests conducted in air and in steam. In air and in steam, creep run-out defined as 100 h at creep stress was achieved at 16 MPa. Similar creep strains were accumulated in air and in steam. Furthermore, creep strain rates and creep lifetimes were only moderately affected by the presence of steam. The retained properties of all specimens that achieved run-out were characterized. Composite microstructure, as well as damage and failure mechanisms were investigated. The tested specimens were also examined using electron probe microanalysis (EPMA) with wavelength dispersive spectroscopy (WDS). Analysis of the fracture surfaces revealed significant surface oxidation, but only trace amounts of boron and carbon. Cross sectional analysis showed increasing boron concentration in the specimen interior

An Audible Demonstration Of The Speed Of Sound In Bubbly Liquids

The speed of sound in a bubbly liquid is strongly dependent upon the volume fraction of the gas phase, the bubble size distribution, and the frequency of the acoustic excitation. At sufficiently low frequencies, the speed of sound depends primarily on the gas volume fraction. This effect can be audibly demonstrated using a one-dimensional acoustic waveguide, in which the flow rate of air bubbles injected into a water-filled tube is varied by the user. The normal modes of the waveguide are excited by the sound of the bubbles being injected into the tube. As the flow rate is varied, the speed of sound varies as well, and hence, the resonance frequencies shift. This can be clearly heard through the use of an amplified hydrophone and the user can create aesthetically pleasing and even musical sounds. In addition, the apparatus can be used to verify a simple mathematical model known as Wood's equation that relates the speed of sound of a bubbly liquid to its void fraction. (c) 2008 American Association of Physics Teachers.Mechanical Engineerin

Development of Optimal Multiscale Patterns for Digital Image Correlation via Local Grayscale Variation

In some applications of digital image correlation (DIC), adequately quantifying deformation of a material can require identification of local deformations which are much smaller than the total field of interest. Instead of exhaustively stitching together images taken at high magnification, it is more efficient to utilize multiple magnifications. Unfortunately, it is rare that the material naturally has features that are useful for image correlation at multiple magnifications. Therefore, an ideal pattern was sought that (1) contains features appropriate for the multiple magnifications, (2) need not know location of high magnification a priori, and (3) can be viewed with standard DIC equipment. An optimization framework was developed based on the inclusion of local grayscale biases which can produce multiscale DIC patterns that satisfy these criteria. Numerical and physical experiments were also performed to illustrate the functionality and utility of the designed patterns

Selectively Electron-Transparent Microstamping Toward Concurrent Digital Image Correlation and High-Angular Resolution Electron Backscatter Diffraction (EBSD) Analysis

High resolution digital image correlation (HRDIC) and high resolution electron backscatter diffraction (HREBSD) provide valuable and complementary data concerning local deformation at the microscale. However, standard surface preparation techniques are mutually exclusive, which makes combining these techniques in situ impossible. This paper introduces a new method of applying surface patterning for HRDIC, namely a urethane rubber microstamp, that provides a pattern with enough contrast for HRDIC at low accelerating voltages, but is still virtually transparent at the higher voltages necessary for HREBSD and conventional electron backscatter diffraction (EBSD) analysis. Furthermore, microstamping is inexpensive and repeatable, and is more amenable to application of patterns to complex surface geometries and larger surface areas than other patterning techniques

Grasshopper Control

This archival publication may not reflect current scientific knowledge or recommendations. Current information available from the University of Minnesota Extension: https://www.extension.umn.edu

Comparison of Dislocation Characterization by Electron Channeling Contrast Imaging and Cross-Correlation Electron Backscattered Diffraction

In this work, the relative capabilities and limitations of electron channeling contrast imaging (ECCI) and cross-correlation electron backscattered diffraction (CC-EBSD) have been assessed by studying the dislocation distributions resulting from nanoindentation in body centered cubic Ta. Qualitative comparison reveals very similar dislocation distributions between the CC-EBSD mapped GNDs and the ECC imaged dislocations. Approximate dislocation densities determined from ECC images compare well to those determined by CC-EBSD. Nevertheless, close examination reveals subtle differences in the details of the distributions mapped by these two approaches. The details of the dislocation Burgers vectors and line directions determined by ECCI have been compared to those determined using CC-EBSD and reveal good agreement

An introductory view on archaeoastronomy

Archaeoastronomy is still a marginalised topic in academia and is described by the Sophia Centre, the only UK institution offering a broader MA containing this field, as ‘the study of the incorporation of celestial orientation, alignments or symbolism in human monuments and architecture’. By many it is associated with investigating prehistoric monuments such as Stonehenge and combining astronomy and archaeology. The following will show that archaeoastronomy is far more than just an interdisciplinary field linking archaeology and astronomy. It merges aspects of anthropology, ethno-astronomy and even educational research, and is possibly better described as cultural astronomy. In the past decades it has stepped away from its quite speculative beginnings that have led to its complete rejection by the archaeology community. Overcoming these challenges it embraced full heartedly solid scientific and statistical methodology and achieved more credibility. However, in recent times the humanistic influences of a cultural context motivate a new generation of archaeoastronomers that are modernising this subject; and humanists might find it better described as post-modern archaeoastronomy embracing the pluralism of today’s academic approach to landscape and ancient people

A model for the degradation of polyimides due to oxidation

Polyimides, due to their superior mechanical behavior at high temperatures, are used in a variety of applications that include aerospace, automobile and electronic packaging industries, as matrices for composites, as adhesives etc. In this paper, we extend our previous model in [S. Karra, K. R. Rajagopal, Modeling the non-linear viscoelastic response of high temperature polyimides, Mechanics of Materials, In press, doi:10.1016/j.mechmat.2010.09.006], to include oxidative degradation of these high temperature polyimides. Appropriate forms for the Helmholtz potential and the rate of dissipation are chosen to describe the degradation. The results for a specific boundary value problem, using our model compares well with the experimental creep data for PMR-15 resin that is aged in air.Comment: 13 pages, 2 figures, submitted to Mechanics of Time-dependent Material