Single-/Few-Layer Graphene as Long-Lasting Electrocatalyst for Hydrogen Evolution Reaction

The development of carbonaceous materials electro-catalytically active for water splitting reactions could overcome multiple disadvantages of metallic catalysts, including high cost, low selectivity, poor durability, and susceptibility to evolved gas. General guidelines to design carbon-based hydrogen evolution reaction (HER) electrocatalysts still remain a topic of debate. Here, we identify single-/few-layer graphene flakes with defective edges (SLG/FLG-DE), produced by hydrogen peroxide-assisted cosolvent liquid phase exfoliation, as durable and efficient HER electrocatalysts. The SLG/FLG-DE display overpotentials at 10 mA cm(-2) of 55 and 85 mV in 0.5 M H2SO4 and 1 M KOH solutions, respectively, as well as a durable HER activity over 200 h

Study of hot corrosion of single crystal superalloys and platinum-aluminide coatings

At the present time, combined cycle systems for power generation (e. g. IGCC), offer increased efficiency of power generation and lower environmental emissions, specifically C02, SOx, and NOx, as well as being adaptable to most fossil fuels. Economic factors, such as the cost of the materials must be considered. Materials influence the service lifetime in the required operational environment. Solid fuels like coal and biomass produce different combustion environments containing a range of contaminants that, when they reach their melting points, may cause accelerated corrosion, affecting directly the service life time of the gas turbine constructional materials. This accelerated corrosion is known as Hot Corrosion. The aim of this study was to develop, an understanding of the influence of these environmental factors on rate of hot corrosion of modem turbine materials, i. e. the single crystal alloys CMSX4 the SC2 , both uncoated and PtAl coated that are needed for a gas turbine blade and vanes operating in a range of hot corrosion environments expected in an lGCC plant. To achieve this aim, a series of laboratory corrosion tests was planned to simulate the same corrosion environment as in industrial high temperature gas turbine operation. Following established procedures for corrosion testing, samples were exposed in a controlled atmosphere furnace to a mix of gases (air/SO241CI) with a cyclic exposure time of 50 and/or 100h duration. Each cycle, samples were removed to be recoated with an alkali salt mixture to a total exposure time of 500h and or 1000h. Cross sections were examined by SEM/EDX to identify the mode of hot corrosion attack. To quantify the rate of corrosion, samples were measured pre-exposure and post-exposure, and this corrosion data was statistically assessed. Finally, from this quantitative data, life prediction models were developed to describe/predict the onset of hot corrosion and the corrosion rates observed under different gas compositions, and various deposition fluxes, both at typical type I and type II hot corrosion temperatures in terms of incubation and propagation periods. Separate models have been developed for the two single crystals superalloys: CMSX4 and SC2, in both the uncoated and platinum aluminide coated condition. The goodness of fit as defined by the regression coefficient varies from 0.88 to 0.99 for the propagation models at 700 and 900°C. The incubation models are as precise at 7001C but less precise at 9001C with regression coefficients of 0.78-0.94. IEThOS - Electronic Theses Online ServiceGBUnited Kingdo

On the rotational dynamics of the Rattleback

The Rattleback is a very popular science toy shown to students all over the world to demonstrate the non-triviality of rotational motion. When spun on a horizontal table, this boat-shaped object behaves in a peculiar way. Although the object appears symmetric, the dynamics of its motion seem very asymmetric. When spun in the preferred direction, it spins smoothly, whereas in the other direction it starts to oscillate wildly. The oscillation soon dies out and the rattleback starts to spin in the preferred way. We will construct and go through an analytical model capable of explaining this behaviour in a simple and intelligible way. Although we aim at a semi-pedagogical treatise, we will study the details only when they are necessary to understand the calculation. After presenting the calculations we will discuss the physical validity of our assumptions and take a look at more sophisticated models requiring numerical analysis. We will then improve our model by assuming a simple friction force.Comment: 17 pages and 2 figures, typos corrected, some minor additions and rewording

Adaptive neuro-fuzzy inference systems (ANFIS) for supervised classification of competence in MIS based on psychomotor skills

INTRODUCTION: Objective assessment of motor skills has become an important challenge in minimally invasive surgery (MIS) training.Currently, there is no gold standard defining and determining the residents' surgical competence.To aid in the decision process, we analyze the validity of a supervised classifier to determine the degree of MIS competence based on assessment of psychomotor skills METHODOLOGY: The ANFIS is trained to classify performance in a box trainer peg transfer task performed by two groups (expert/non expert). There were 42 participants included in the study: the non-expert group consisted of 16 medical students and 8 residents ( 10 MIS procedures performed) and 4 experienced surgeons. Instrument movements were captured by means of the Endoscopic Video Analysis (EVA) tracking system. Nine motion analysis parameters (MAPs) were analyzed, including time, path length, depth, average speed, average acceleration, economy of area, economy of volume, idle time and motion smoothness. Data reduction was performed by means of principal component analysis, and then used to train the ANFIS net. Performance was measured by leave one out cross validation. RESULTS: The ANFIS presented an accuracy of 80.95%, where 13 experts and 21 non-experts were correctly classified. Total root mean square error was 0.88, while the area under the classifiers' ROC curve (AUC) was measured at 0.81. DISCUSSION: We have shown the usefulness of ANFIS for classification of MIS competence in a simple box trainer exercise. The main advantage of using ANFIS resides in its continuous output, which allows fine discrimination of surgical competence. There are, however, challenges that must be taken into account when considering use of ANFIS (e.g. training time, architecture modeling). Despite this, we have shown discriminative power of ANFIS for a low-difficulty box trainer task, regardless of the individual significances between MAPs. Future studies are required to confirm the findings, inclusion of new tasks, conditions and sample population

Systems and technologies for objective evaluation of technical skills in laparoscopic surgery

Minimally invasive surgery is a highly demanding surgical approach regarding technical requirements for the surgeon, who must be trained in order to perform a safe surgical intervention. Traditional surgical education in minimally invasive surgery is commonly based on subjective criteria to quantify and evaluate surgical abilities, which could be potentially unsafe for the patient. Authors, surgeons and associations are increasingly demanding the development of more objective assessment tools that can accredit surgeons as technically competent. This paper describes the state of the art in objective assessment methods of surgical skills. It gives an overview on assessment systems based on structured checklists and rating scales, surgical simulators, and instrument motion analysis. As a future work, an objective and automatic assessment method of surgical skills should be standardized as a means towards proficiency-based curricula for training in laparoscopic surgery and its certification

Apoptotic cells subjected to cold/warming exposure disorganize apoptotic microtubule network and undergo secondary necrosis

Apoptotic microtubule network (AMN) is organized during apoptosis, forming a cortical structure beneath the plasma membrane which plays a critical role in preserving cell morphology and plasma membrane integrity. The aim of this study was to examine the effect of cold/warming exposure on apoptotic microtubules and plasma membrane integrity during the execution phase of apoptosis. We demonstrated in camptothecin-induced apoptotic H460 cells that cold/warming exposure disorganized apoptotic microtubules and allowed the access of active caspases to the cellular cortex and the cleavage of essential proteins in the preservation of plasma membrane permeability. Cleavage of cellular cortex and plasma membrane proteins, such as ¿-spectrin, paxilin, focal adhesion kinase and calcium ATPase pump (PMCA-4) involved in cell calcium extrusion resulted in increased plasma permeability and calcium overload leading apoptotic cells to secondary necrosis. The essential role of caspase-mediated cleavage in this process was demonstrated because the addition of the pan-caspase inhibitor z-VAD during cold/warming exposure that induces AMN depolymerization avoided the cleavage of cortical and plasma membrane proteins and prevented apoptotic cells to undergo secondary necrosis. Likewise, apoptotic microtubules stabilization by taxol during cold/warming exposure also prevented cellular cortex and plasma membrane protein cleavage and secondary necrosis. Furthermore, microtubules stabilization or caspase inhibition during cold/warming exposure was also critical for proper phosphatidylserine externalization and apoptotic cell clearance by macrophages. These results indicate that cold/warming exposure of apoptotic cells induces secondary necrosis which can be prevented by both, microtubule stabilization or caspase inhibition.This work was supported by FIS PI10/00543 Grant, FIS EC08/00076 Grant, Ministerio de Sanidad, Spain and Fondo Europeo de Desarrollo Regional (FEDER-Unión Europea), SAS 111242 Grant, Servicio Andaluz de Salud-Junta de Andalucía, Proyecto de Investigación de Excelencia de la Junta de Andalucía CTS-5725, and by Asociación de Enfermos de Patología Mitocondrial (AEPMI).Peer Reviewe

Stabilization of apoptotic cells: generation of zombie cells

This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported License.Apoptosis is characterized by degradation of cell components but plasma membrane remains intact. Apoptotic microtubule network (AMN) is organized during apoptosis forming a cortical structure beneath plasma membrane that maintains plasma membrane integrity. Apoptotic cells are also characterized by high reactive oxygen species (ROS) production that can be potentially harmful for the cell. The aim of this study was to develop a method that allows stabilizing apoptotic cells for diagnostic and therapeutic applications. By using a cocktail composed of taxol (a microtubule stabilizer), Zn2+ (a caspase inhibitor) and coenzyme Q10 (a lipid antioxidant), we were able to stabilize H460 apoptotic cells in cell cultures for at least 72 h, preventing secondary necrosis. Stabilized apoptotic cells maintain many apoptotic cell characteristics such as the presence of apoptotic microtubules, plasma membrane integrity, low intracellular calcium levels and mitochondrial polarization. Apoptotic cell stabilization may open new avenues in apoptosis detection and therapy.This work was supported by FIS PI10/00543 grant, Ministerio de Sanidad, Spain, and Fondo Europeo de Desarrollo Regional (FEDER-Unión Europea), SAS 111242 grant, Servicio Andaluz de Salud-Junta de Andalucía, Proyecto de Investigación de Excelencia de la Junta de Andalucía CTS-5725, BFU2012-38208 and by AEPMI (Asociación de Enfermos de Patología Mitocondrial).Peer Reviewe

Performance Comparison Between Isothermal Hot Corrosion And In Situ Cyclic Hot Corrosion of Nickel-Based Superalloys

Although a lot of work has been done to understand both major mechanisms of hot corrosion, namely type I (high-temperature hot corrosion) and type II (low temperature hot corrosion), there is very little information available on more representative cyclic performance in these regimes. This work addresses this by assessing the performance of isothermal (type I and type II) hot corrosion tests against combined (short and long) cyclic corrosion tests. Single-crystal alloy PWA 1484 and directionally solidified alloy MAR-M247 were assessed in all test regimes. Pre- and post-exposure dimensional metrology was used to quantify the corrosion damage and characterised using SEM/EDX. This paper highlights that the results of short cycle test conditions are more damaging compared to long cycle and standard isothermal type I and II test conditions. The cast nickel-based alloy MAR-M247 was found to be a better performer compared to PWA 1484 single-crystal alloy

Performance Comparison Between Isothermal Hot Corrosion And In Situ Cyclic Hot Corrosion of Nickel-Based Superalloys

Although a lot of work has been done to understand both major mechanisms of hot corrosion, namely type I (high-temperature hot corrosion) and type II (low temperature hot corrosion), there is very little information available on more representative cyclic performance in these regimes. This work addresses this by assessing the performance of isothermal (type I and type II) hot corrosion tests against combined (short and long) cyclic corrosion tests. Single-crystal alloy PWA 1484 and directionally solidified alloy MAR-M247 were assessed in all test regimes. Pre- and post-exposure dimensional metrology was used to quantify the corrosion damage and characterised using SEM/EDX. This paper highlights that the results of short cycle test conditions are more damaging compared to long cycle and standard isothermal type I and II test conditions. The cast nickel-based alloy MAR-M247 was found to be a better performer compared to PWA 1484 single-crystal alloy

Laparoscopic Video Analysis for Training and Image Guided Surgery

Automatic analysis of Minimally Invasive Surgical video has the potential to drive new solutions for alleviating needs of safe and reproducible training programs, objective and transparent evaluation systems and navigation tools to assist surgeons and improve patient safety. Surgical video is an always available source of information, which can be used without any additional intrusive hardware in the operating room. This paper is focused on surgical video analysis methods and techniques. It describes authors' contributions in two key aspects, the 3D reconstruction of the surgical field and the segmentation and tracking of tools and organs based on laparoscopic video images. Results are given to illustrate the potential of this field of research, like the calculi of the 3D position and orientation of a tool from its 2D image, or the translation of a preoperative resection plan into a hepatectomy surgical procedure using the shading information of the image. Research efforts are required to further develop these technologies in order to harness all the valuable information available in any video-based surgery