7,586 research outputs found
Ranking the Risks: The 10 Pathogen-Food Combinations With the Greatest Burden on Public Health
Examines food-borne pathogens with the highest disease burdens and the top ten foods most commonly contaminated by them, such as salmonella in poultry, toxoplasma in pork, and listeria in deli meats. Makes policy recommendations for improving prevention
An Investigation of the Sled Push Exercise: Quantification of Work, Kinematics, and Related Physical Characteristics
The purpose of this dissertation was to describe the basic characteristics of performing resisted sprint training using a push sled for the enhancement of sport performance. Specifically, this dissertation served to: 1.) quantify the frictional forces involved between a push sled and an AstroTurf® surface at 6 loads, 2.) derive an estimation of mechanical work performed during sled push training, 3.) outline the velocity characteristics of 3 sled pushing loads scaled to the athletes body mass for comparison against their sprinting ability and 4.) determine the interrelations of fitness characteristics to the ability to sprint under heavy resistance.
The following are major findings of this dissertation. 1.) Coefficients of static friction (0.53 – 0.37) and dynamic friction (0.35 – 0.28) were calculated at multiple loads for the AstroTurf® surface. 2.) A direct near perfect relationship exists between total system load of the sled and the forces required to initiate and maintain movement of the sled. Although a direct measurement of force would be more precise and account for changes in velocity, the total system load may be a more practical alternative for daily use. 3.) Statistically significant changes in velocity characteristics were observed within each sled pushing load as well as when comparing each load to sprinting. Decrements in peak velocity ranged from about 40%-51% when comparing resisted to unresisted sprinting. Load increments of 25% body mass were heavy enough to cause statistically significant differences in velocity characteristics. 4.) Statistically significant correlations were observed in anthropometry, sprinting ability, jumping ability, and strength to sled pushing. The results indicate that larger athletes, who can not only produce greater force but produce those forces rapidly, in addition to excelling at jumping and sprinting compared to their peers demonstrate the ability to move faster against heavy loads and slow down less from unresisted conditions. The strongest athletes demonstrated statistically nonsignificant differences in peak velocity drop off when compared to their weaker counterparts; however, small to moderate effect sizes (d = 0.27 – 1.02) were observed indicating a practical difference between strength levels in peak velocity and peak velocity drop off
Investigating the Photoyield of Spacecraft Materials
Understanding the photon-induced charging of spacecraft materials is necessary in modeling the overall charging of a spacecraft. Measuring the photoyields of insulators requires sophistication, since insulators\u27 electrons must overcome a greater potential energy barrier, than electrons in a metal, to move within a solid. In order to determine the photoyields of insulating and semiconducting materials for NASA\u27s Solar Probe Mission (PBN, Alumina) and James Webb Space Telescope project (SixPI-ExVDA), a chopper and lock-in amplifier were added to a photoyield measurement system. A standard (Au) photoemission spectrum was compared with Au spectrum taken before addition of the lock-in to verify the validity of the modified system. Two insulators (polyboron nitride and Alumina) under investigation for the NASA/APL Solar Probe Mission and materials for the JWST project (vapor deposited aluminum and silicon on substrate Kapton E) were then studied using the modified photoemission measurement system. The resulting spectra were used to calculate the solar photoelectron yield and work function of each of the materials
Embedded Charge Distributions in Electron Irradiated Polymers – Pulsed Electroacoustic Method Reproducibility and Calibration
The pulsed electroacoustic (PEA) method has been used to measure the embedded charge distributions in electron irradiated polymers. The PEA method allows for non-destructive direct measurements of embedded charge distributions in dielectric materials. Samples of polyether-etherketone (PEEK) and polytetrafluoroethylene (PTFE) of 125 μm or 250 μm thickness were tested after irradiation with either a 50 keV or 80 keV electron beam. The reproducibility of the PEA method and the experimental conditions were studied by: (i) measuring each sample multiple times in a given mounting configuration, (ii) re-measuring each sample after repositioning them in the PEA test fixture, and (iii) measuring two similar samples of each of these eight different experimental configurations. For accurate absolute measurements of the charge distribution and deposition depths, calibration of charge position, charge density, and amplitude attenuation for the PEA system are required. Calibration is accomplished by measuring the speed of sound in each material and by observing the effects of applying a small DC voltage to use as a reference signal. A deconvolution of the measured waveform is performed with the reference signal to remove the effects of system response, resulting in only the charge distribution. Reproducibility of measurements before and after application of DC voltage identified any effects of the applied voltage
Spatial and temporal variations in precipitation and cloud interception in the Sierra Nevada of central California
Spatial and temporal variations in patterns of precipitation and cloud interception were studied for a period of 14 months in the Sierra Nevada of central California. 14 fully automated sampling stations, located at elevations from 800 to 2400 m, were utilized in the study. Both precipitation and cloud interception were observed to increase with elevation. Cloudwater deposition increased at higher elevations due both to a greater frequency of cloud interception and higher wind speeds. Cloudwater deposition, caused primarily by the interception of clouds associated with cold fronts approaching from the north or north-west, is most important at elevations above 1500 m; however, the interception of highly polluted winter “Tule” fogs, lifting above the floor of the San Joaquin Valley, appears to be an important mechanism for cloudwater deposition at lower elevation sites. Observed and estimated hydrological and chemical inputs to the passive cloudwater collectors used in the study were substantial, suggesting that cloud interception may contribute significantly to the same inputs for exposed conifers in the region
Lean development evaluation in small Brazilian company
Purpose – The small Brazilian companies are responsible for a large part of national GDP and formal jobs in the country. This expressiveness is contrasted with the specificities of companies of this size possess, including the need to innovate to survive. Research shows that 83 percent of Brazilian SMEs have launched new products and services, obtaining positive results through this innovative process. This competitive advantage is weighted by a great feature of the small organization: resource constraint. The paper aims to discuss this issue. Design/methodology/approach – Research was carried out in three stages: one qualitative research (by using focal groups) and another two quantitative research works (descriptive and cross-sectional). Findings – The author identified three factors that are important for teenagers when influencing the purchase of the family car: safety, sportiness and comfort. The identification of these factors shows that the millennial generation tends to emphasize aspects of individual interest, such as status and performance, and family context, such as safety and comfort, rather than social aspects, such as the type of fuel and environmental impact. Social implications – The authors recommend the development of automobiles that prioritize the three factors mentioned herein in order to reverse the trend of declining car purchase. Originality/value – The authors presented the relevant attributes in buying decisions of family cars according to teenagers. The authors also indicated which automobile attributes are relevant for a more informed, connected, and with an increasing purchase power generation in contrast with previous generations, whose social context was prior to the emergence of social media
Cloud water chemistry in Sequoia National Park
Interception of cloudwater by forests in the Sierra Nevada Mountains may contribute significantly to acidic deposition in the region. Cloudwater sampled in Sequoia National Park had pH values ranging from 4.4 to 5.7. The advance of cold fronts into the Park appears to lead to higher aerosol and gas phase concentrations than are seen under normal mountain-valley circulations, producing higher cloud-water concentrations than might otherwise be expected. Estimates of annual deposition rates of NO_3^−, SO_4^(2−), NH_4^+ and H^+ due to cloudwater impaction are comparable to those measured in precipitation
The Correlation Between Radiation Induced Conductivity (RIC) and Electron Beam Induced Luminescence in Disordered SiO2
- …