A High Diffusive Model for Nanomaterials

Considerable attention is today devoted to the engineering of films widely used in photocatalytic, solar energy converters, photochemical and photoelectrochemical cells, dye-sensitized solar cells (DSSCs), to optimize electronic time response following photogeneration. However, the precise nature of transport processes in these systems has remained unresolved. To investigate such aspects of carrier dynamics, we have suggested a model for the calculation of correlation functions, expressed as the Fourier transform of the frequency-dependent complex conductivity σ(ω). Results are presented for the velocity correlation functions, the mean square deviation of position and the diffusion coefficient in systems, like TiO2 and doped Si, of large interest in present devices. Fast diffusion occurs in short time intervals of the order of few collision times. Consequences for efficiency of this fast response are discussed in relation to nanostructured devices

CdSe quantum dot (QD) and molecular dye hybrid sensitizers for TiO2 mesoporous solar cells: working together with a common hole carrier of cobalt complexes

Redox couples based on cobalt complexes were found to be effective in regenerating both inorganic CdSe quantum dot-and organic dye-sensitizers. The hybrid sensitizer composed of CdSe QD and ruthenium sensitizer (Z907Na) dye showed a maximum power conversion efficiency of 4.76% on using cobalt(o-phen)(3)(2+/3+) as a common redox mediator.close202

Gallium arsenide p-i-n radial structures for photovoltaic applications

Gallium arsenide p-i-n radial junctions were fabricated by molecular beam epitaxy. The current-voltage characteristics of single nanowires were measured in the dark and under various illumination conditions including 1.5 AM. The total efficiency was 4.5%. Spatially resolved and power dependent photocurrent measurements indicate that the p-i-n junction is homogeneous along the nanowire. Electroluminescence measurements show an emission peak at about 1.4 eV, further corroborating the good quality of the nanowire. These results constitute an important progress for the use of nanowires in photovoltaic applications

Exact asymptotics for non-radiative migration-accelerated energy transfer in one-dimensional systems

We study direct energy transfer by multipolar or exchange interactions between diffusive excited donor and diffusive unexcited acceptors. Extending over the case of long-range transfer of an excitation energy a non-perturbative approach by Bray and Blythe [Phys. Rev. Lett. 89, 150601 (2002)], originally developed for contact diffusion-controlled reactions, we determine exactly long-time asymptotics of the donor decay function in one-dimensional systems.Comment: 16 page

Hierarchical TiO2 Photoanode for Dye-Sensitized Solar Cells

n/

Enhanced Electron Collection Efficiency in Dye-Sensitized Solar Cells Based on Nanostructured TiO2 Hollow Fibers

Nanostructured TiO2 hollow fibers have been prepared using natural cellulose fibers as a template. This cheap and easily processed material was used to produce highly porous photoanodes incorporated in dye-sensitized solar cells and exhibited remarkably enhanced electron transport properties compared to mesoscopic films made of spherical nanoparticles. Photoinjected electron lifetime, in particular, was multiplied by 3-4 in the fiber morphology, while the electron transport rate within the fibrous photoanaode was doubled. A nearly quantitative absorbed photon-to-electrical current conversion yield exceeding 95% was achieved upon excitation at 550 nm and a photovoltaic power conversion efficiency of 7.2% reached under simulated AM 1.5 (100 mW cm(-2)) solar illumination

Hydrothermally Processed Oxide Nanostructures and Their Lithium–ion Storage Properties

Y- and Si-based oxide nanopowders were synthesized by a hydrothermal reaction of Y or Si powders with NaOH or LiOH aqueous solution. Nanoparticles with different morphology such as elongated nanospheres, flower-like nanoparticles and nanowires were produced by a control of processing parameters, in particular, the starting composition of solution. The preliminary result of electrochemical examination showed that the hydrothermally processed nanowires exhibit high initial capacities of Li-ion storage: 653 mAh/g for Y2O3 nanowires as anode materials and 186 mAh/g for Li2Si2O5 nanowires as cathode materials in a Li secondary cell. Compared to the powder with elongated sphere or flower-like shapes, the nanowires showed a higher Li-ion capacity and a better cycle property

Molecular-Scale Interface Engineering of Nanocrystalline Titania by Co-adsorbents for Solar Energy Conversion

The use of mixed self-assembled monolayers, combining hydrophobic co-adsorbents with the sensitizer, has been demonstrated to enhance the efficiency of dye-sensitized solar cells (DSCs). Herein, the influence of the anchoring groups of the co-adsorbents on the performance of the DSCs is carefully examined by selecting two model molecules: neohexyl phosphonic acid (NHOOP) and bis-(3,3-dimethyl-butyl)-phosphinic acid (DINHOP). The effect of these co-adsorbents on the photovoltaic performance (JV curves, incident photon-to-electron conversion efficiency) is investigated. Photoelectron spectroscopy and electrochemical impedance spectroscopy are performed to assess the spatial configuration of adsorbed dye and co-adsorbent molecules. The photoelectron spectroscopy studies indicate that the ligands of the ruthenium complex, containing thiophene groups, point out away from the surface of TiO2 in comparison with the NCS group

Hill climbing hysteresis of perovskite-based solar cells: a maximum power point tracking investigation

The surge of the power conversion efficiency of metal halide lead perovskite solar cells comes with concerns, such as the long-term ecotoxicity of lead compounds, their sensitivity toward moisture and oxygen, or the scarcity of some of their components. Most perovskite solar cells still suffer from serious stability problems when measured under real working conditions (maximum power point tracking at 60 degrees C). In the long run, stability will certainly decide on the fate of CH3NH3PbI3 and related lead perovskites for their use in photovoltaic modules. Herein, we show an effective and inexpensive strategy to perform ageing of perovskite solar cells under maximum power point tracking. For the first time, we analyze the issue of power extraction from solar cells exhibiting hysteresis. We show that a standard tracking algorithm such as perturb and observe fails to converge to the maximum power point of the solar cell if it exhibits j(V) hysteresis, and we present an effective strategy to stabilize the algorithm. We show that enforcing oscillations in forward bias can boost the mean power output of some perovskite solar cells by more than 10%, in contrast to a reference crystalline silicon solar cell. Copyright (c) 2017 John Wiley & Sons, Ltd

A Thiophene-Based Anchoring Ligand and Its Heteroleptic Ru(II)-Complex for Efficient Thin-Film Dye-Sensitized Solar Cells

A novel heteroleptic Ru-II complex (BTC-2) employing 5,5'-(2,2'-bipyridine-4,4'-diyl)-bis(thiophene-2-carboxylic acid) (BTC) as the anchoring group and 4,4'-dinonyl-2,2'-bipiridyl and two thiocyanates as ligands is prepared. The photovoltaic performance and device stability achieved with this sensitizer are compared to those of the Z-907 dye, which lacks the thiophene moieties. For thin mesoporous TiO2 films, the devices with BTC-2 achieve higher power conversion efficiencies than those of Z-907 but with a double-layer thicker film the device performance is similar. Using a volatile electrolyte and a double layer 7 + 5 mu m mesoporous TiO2 film, BTC-2 achieves a solar-to-electricity conversion efficiency of 9.1% under standard global AM 1.5 sunlight. Using this sensitizer in combination with a low volatile electrolyte, a photovoltaic efficiency of 8.3% is obtained under standard global AM 1.5 sunlight. These devices show excellent stability when subjected to light soaking at 60 degrees C for 1000 h. Electrochemical impedance spectroscopy and transient photovoltage decay measurements are performed to help understand the changes in the photovoltaic parameters during the aging process. In solid state dye-sensitized solar cells (DSSCs) using an organic hole-transporting material (spiro-MeOTAD, 2,2',7,7'-tetrakis-(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene), the BTC-2 sensitizer exhibits an overall power conversion efficiency of 3.6% under AM 1.5 solar (100 mW cm(-2)) irradiation