The effects of high-temperature brazing and thermal cycling on the mechanical properties of Hastelloy X

Data are presented on the effects of brazing alloy, brazing operation, thermal cycling, and combinations of these on the yield strength, elongation, tensile strength, and fatigue life of thin gage Hastelloy X. These data show that brazing at 1461 K (2170 F) with a Ni-Pd-Au alloy and subsequent exposure to 200 service thermal cycles between 533 and 1144 K (500 and 1600 F) result in reduction of as much as 39 percent in yield strength, 33 percent in elongation, 14 percent in tensile strength, and 26 percent in fatigue limit of Hastelloy X, as compared to as-received materials. These property losses are primarily caused by the brazing operation rather than the subsequent service thermal cycles

Fatigue crack growth in 7475-T651 aluminum alloy plate in hard vacuum and water vapor

Compact specimens of 25 mm thick aluminum alloy plate were subjected to constant amplitude fatigue testing at a load ratio of 0.2. Crack growth rates were determined at frequencies of 1 Hz and 10 Hz in hard vacuum and laboratory air, and in mixtures of water vapor and nitrogen at water vapor partial pressures ranging from 94 Pa to 3.8 kPa. A significant effect of water vapor on fatigue crack growth rates was observed at the lowest water vapor pressure tested. Crack rates changed little for pressures up to 1.03 kPa, but abruptly accelerated at higher pressures. At low stress intensity factor ranges, cracking rates at the lowest and highest water vapor pressure tested were, respectively, two and five times higher than rates in vacuum. Although a frequency was observed in laboratory air, cracking rates in water vapor and vacuum are insensitive to a ten-fold change in frequency. Surfaces of specimens tested in water vapor and vacuum exhibited different amounts of residual deformation. Reduced deformation on the fracture surfaces of the specimens tested in water vapor suggests embrittlement of the plastic zone ahead of the crack tip as a result of environmental interaction

The effect of water vapor on fatigue crack Growth in 7475-t651 aluminum alloy plate

The effects of water vapor on fatigue crack growth in 7475-T651 aluminum alloy plate at frequencies of 1 Hz and 10 Hz were investigated. Twenty-five mm thick compact specimens were subjected to constant amplitude fatigue testing at a load ratio of 0.2. Fatigue crack growth rates were calculated from effective crack lengths determined using a compliance method. Tests were conducted in hard vacuum and at water vapor partial pressures ranging from 94 Pa to 3.8 kPa. Fatigue crack growth rates were frequency insensitive under all environment conditions tested. For constant stress intensity factor ranges crack growth rate transitions occurred at low and high water vapor pressures. Crack growth rates at intermediate pressures were relatively constant and showed reasonable agreement with published data for two Al-Cu-Mg alloys. The existence of two crack growth rate transitions suggests either a change in rate controlling kinetics or a change in corrosion fatigue mechanism as a function of water vapor pressure. Reduced residual deformation and transverse cracking specimens tested in water vapor versus vacuum may be evidence of embrittlement within the plastic zone due to environmental interaction

Ablative performance of uncoated silicone-modified and shuttle baseline reinforced carbon composites

The relative ablative performance of uncoated silicone-modified reinforced carbon composite (RCC) and uncoated shuttle baseline RCC substrates was investigated. The test specimens were 13 plies (5.3 to 5.8 millimeters) thick and had a 25-millimeter-diameter test face. Prior to arc tunnel testing, all specimens were subjected to a heat treatment simulating the RCC coating process. During arc tunnel testing, the specimens were exposed to cold wall heating rates of 178 to 529 kilowatts/sq m and stagnation pressures ranging from 0.015 to 0.046 atmosphere at Mach 4.6 in air, with and without preheating in nitrogen. The results show that the ablative performance of uncoated silicone-modified RCC substrates is significantly superior to that of uncoated shuttle baseline RCC substrates over the range of heating conditions used. These results indicate that the silicone-modified RCC substrate would yield a substantially greater safety margin in the event of complete coating loss on the shuttle orbiter

Modified Composite Materials Workshop

The reduction or elimination of the hazard which results from accidental release of graphite fibers from composite materials was studied at a workshop. At the workshop, groups were organized to consider six topics: epoxy modifications, epoxy replacement, fiber modifications, fiber coatings and new fibers, hybrids, and fiber release testing. Because of the time required to develop a new material and acquire a design data base, most of the workers concluded that a modified composite material would require about four to five years of development and testing before it could be applied to aircraft structures. The hybrid working group considered that some hybrid composites which reduce the risk of accidental fiber release might be put into service over the near term. The fiber release testing working group recommended a coordinated effort to define a suitable laboratory test

Dips in Partial Wave Amplitudes from Final State Interactions

We consider the dip-peak structures in the J=0 partial wave amplitudes for processes \gamma\gamma\rightarrow W^+W^-~ \mbox{and}~\gamma\gamma,gg\rightarrow t\overline{t} taking into account the corresponding Born term process and the rescattering process where the intermediate state is rescattered through the exchange of Higgs resonance state in the direct channel.Comment: 9 pages, CPP-93-21, 6 figures not include

Emittance of TD-NiCr after simulated reentry

The effects of simulated reentry heating on the emittance of TD-NiCr were investigated. Groups of specimens with three different preconditioning treatments were exposed to 6, 24, and 30 half-hour simulated reentry exposure cycles in a supersonic arc tunnel at each of three conditions intended to produce surface temperatures of 1255, 1365, and 1475 K. Emittance was determined at 1300 K on specimens which were preconditioned only and specimens after completion of reentry simulation exposure. Oxide morphology and chemistry were studied by scanning electron microscopy and X-ray diffraction analysis. A consistent relationship was established between oxide morphology and total normal emittance. Specimens with coarser textured oxides tended to have lower emittances than specimens with finer textured oxides

Effects of sea salts on the physical characteristics of reusable surface insulation

Test results show that sea salt contamination and thermal cycles cause significant changes in the morphology of surface insulation coatings with increased melting. Sea salt contamination and thermal cycles do not have a significant effect on emittance of mullite and silica composite coatings at high temperatures (1300 K). At the lower temperatures there is apparently some effect on emittance but the evidence is inconclusive because of the absence of multiple tests

Supersymmetric photonic signals at LEP

We explore and contrast the single-photon and diphoton signals expected at LEP 2, that arise from neutralino-gravitino (e^+ e^- -> chi + gravitino -> gamma + E_miss) and neutralino-neutralino (e^+ e^- -> chi + chi -> gamma + gamma + E_miss) production in supersymmetric models with a light gravitino. LEP 1 limits imply that one may observe either one, but not both, of these signals at LEP 2, depending on the values of the neutralino and gravitino masses: single-photons for m_chi > Mz and m_gravitino < 3 x 10^-5 eV; diphotons for m_chi < Mz and all allowed values of m_gravitino.Comment: 11 pages, LaTeX, 4 figures (included). Shortened version to appear in Physical Review Letter

gamma nu -> gamma gamma nu and crossed processes at energies below m_W

The cross sections for the processes $\gamma \nu\to \gamma \gamma \nu$, $\gamma\gamma\to\gamma\nu\bar{\nu}$ and $\nu\bar{\nu}\to\gamma\gamma\gamma$ are calculated for a range of center of mass energies from below $m_e$ to considerably above $m_e$, but much less than $m_W$. This enables us to treat the neutrino--electron coupling as a four--Fermi interaction and results in amplitudes which are electron box diagrams with three real photons and one virtual photon at their vertices. These calculations extend our previous low--energy effective interaction results to higher energies and enable us to determine where the effective theory is reliable.Comment: 12 pages, RevTex, 10 postscript figures include