Anode Front-End Electronics for the Cathode Strip Chambers of the CMS Endcap Muon Detector

The front-end electronics system for the anode signals of the CMS Endcap Muon cathode strip chambers has about 183000 channels. The purposes of the anode front-end electronics are to acquire precise muon timing information for bunch crossing number identification at the Level-1 muon trigger system and to provide a coarse radial position of the muon track. Each anode channel consists of an input protection network, amplifier, shaper, constant-fraction discriminator, and a programmable delay. The essential parts of the electronics include a 16-channel amplifier-shaper-discriminator ASIC CMP16 and a 16-channel ASIC D16G providing programmable time delay. The ASIC CMP16 was optimized for the large cathode chamber size (up to 3 x 2.5 m2) and for the large input capacitance (up to 200 pf). The ASIC combines low power consumption (30 mW/channel) with good time resolution (2 - 3 ns). The del ay ASIC D16G makes possible the alignment of signals with an accuracy of 2.2 ns. This note presents the anode front-end electronics structure and results of the preproduction and the mass production tests, including radiation resistance and reliability tests. The special set of test equipment, techniques, and corresponding software developed and used in the test procedures are also described

Efficiency of Finding Muon Track Trigger Primitives in CMS Cathode Strip Chambers

In the CMS Experiment, muon detection in the forward direction is accomplished by cathode strip chambers~(CSC). These detectors identify muons, provide a fast muon trigger, and give a precise measurement of the muon trajectory. There are 468 six-plane CSCs in the system. The efficiency of finding muon trigger primitives (muon track segments) was studied using~36 CMS CSCs and cosmic ray muons during the Magnet Test and Cosmic Challenge~(MTCC) exercise conducted by the~CMS experiment in~2006. In contrast to earlier studies that used muon beams to illuminate a very small chamber area ($< \! 0.01$~m$^2$), results presented in this paper were obtained by many installed CSCs operating {\em in situ} over an area of $\approx \! 23$~m$^2$ as a part of the~CMS experiment. The efficiency of finding 2-dimensional trigger primitives within 6-layer chambers was found to be~$99.93 \pm 0.03\%$. These segments, found by the CSC electronics within $800$~ns after the passing of a muon through the chambers, are the input information for the Level-1 muon trigger and, also, are a necessary condition for chambers to be read out by the Data Acquisition System

Les droits disciplinaires des fonctions publiques : « unification », « harmonisation » ou « distanciation ». A propos de la loi du 26 avril 2016 relative à la déontologie et aux droits et obligations des fonctionnaires

The production of tt‾ , W+bb‾ and W+cc‾ is studied in the forward region of proton–proton collisions collected at a centre-of-mass energy of 8 TeV by the LHCb experiment, corresponding to an integrated luminosity of 1.98±0.02 fb−1 . The W bosons are reconstructed in the decays W→ℓν , where ℓ denotes muon or electron, while the b and c quarks are reconstructed as jets. All measured cross-sections are in agreement with next-to-leading-order Standard Model predictions.The production of $t\overline{t}$, $W+b\overline{b}$ and $W+c\overline{c}$ is studied in the forward region of proton-proton collisions collected at a centre-of-mass energy of 8 TeV by the LHCb experiment, corresponding to an integrated luminosity of 1.98 $\pm$ 0.02 \mbox{fb}^{-1}. The $W$ bosons are reconstructed in the decays $W\rightarrow\ell\nu$, where $\ell$ denotes muon or electron, while the $b$ and $c$ quarks are reconstructed as jets. All measured cross-sections are in agreement with next-to-leading-order Standard Model predictions

Physics case for an LHCb Upgrade II - Opportunities in flavour physics, and beyond, in the HL-LHC era

The LHCb Upgrade II will fully exploit the flavour-physics opportunities of the HL-LHC, and study additional physics topics that take advantage of the forward acceptance of the LHCb spectrometer. The LHCb Upgrade I will begin operation in 2020. Consolidation will occur, and modest enhancements of the Upgrade I detector will be installed, in Long Shutdown 3 of the LHC (2025) and these are discussed here. The main Upgrade II detector will be installed in long shutdown 4 of the LHC (2030) and will build on the strengths of the current LHCb experiment and the Upgrade I. It will operate at a luminosity up to 2×1034 cm−2s−1, ten times that of the Upgrade I detector. New detector components will improve the intrinsic performance of the experiment in certain key areas. An Expression Of Interest proposing Upgrade II was submitted in February 2017. The physics case for the Upgrade II is presented here in more depth. CP-violating phases will be measured with precisions unattainable at any other envisaged facility. The experiment will probe b → sl+l−and b → dl+l− transitions in both muon and electron decays in modes not accessible at Upgrade I. Minimal flavour violation will be tested with a precision measurement of the ratio of B(B0 → μ+μ−)/B(Bs → μ+μ−). Probing charm CP violation at the 10−5 level may result in its long sought discovery. Major advances in hadron spectroscopy will be possible, which will be powerful probes of low energy QCD. Upgrade II potentially will have the highest sensitivity of all the LHC experiments on the Higgs to charm-quark couplings. Generically, the new physics mass scale probed, for fixed couplings, will almost double compared with the pre-HL-LHC era; this extended reach for flavour physics is similar to that which would be achieved by the HE-LHC proposal for the energy frontier

LHCb upgrade software and computing : technical design report

This document reports the Research and Development activities that are carried out in the software and computing domains in view of the upgrade of the LHCb experiment. The implementation of a full software trigger implies major changes in the core software framework, in the event data model, and in the reconstruction algorithms. The increase of the data volumes for both real and simulated datasets requires a corresponding scaling of the distributed computing infrastructure. An implementation plan in both domains is presented, together with a risk assessment analysis

Multidifferential study of identified charged hadron distributions in ZZ-tagged jets in proton-proton collisions at s=\sqrt{s}=13 TeV

Jet fragmentation functions are measured for the first time in proton-proton collisions for charged pions, kaons, and protons within jets recoiling against a $Z$ boson. The charged-hadron distributions are studied longitudinally and transversely to the jet direction for jets with transverse momentum 20 $< p_{\textrm{T}} < 100$ GeV and in the pseudorapidity range $2.5 < \eta < 4$. The data sample was collected with the LHCb experiment at a center-of-mass energy of 13 TeV, corresponding to an integrated luminosity of 1.64 fb$^{-1}$. Triple differential distributions as a function of the hadron longitudinal momentum fraction, hadron transverse momentum, and jet transverse momentum are also measured for the first time. This helps constrain transverse-momentum-dependent fragmentation functions. Differences in the shapes and magnitudes of the measured distributions for the different hadron species provide insights into the hadronization process for jets predominantly initiated by light quarks.Comment: All figures and tables, along with machine-readable versions and any supplementary material and additional information, are available at https://cern.ch/lhcbproject/Publications/p/LHCb-PAPER-2022-013.html (LHCb public pages

Study of the B−→Λc+Λˉc−K−B^{-} \to \Lambda_{c}^{+} \bar{\Lambda}_{c}^{-} K^{-} decay

The decay $B^{-} \to \Lambda_{c}^{+} \bar{\Lambda}_{c}^{-} K^{-}$ is studied in proton-proton collisions at a center-of-mass energy of $\sqrt{s}=13$ TeV using data corresponding to an integrated luminosity of 5 $\mathrm{fb}^{-1}$ collected by the LHCb experiment. In the $\Lambda_{c}^+ K^{-}$ system, the $\Xi_{c}(2930)^{0}$ state observed at the BaBar and Belle experiments is resolved into two narrower states, $\Xi_{c}(2923)^{0}$ and $\Xi_{c}(2939)^{0}$, whose masses and widths are measured to be $$m(\Xi_{c}(2923)^{0}) = 2924.5 \pm 0.4 \pm 1.1 \,\mathrm{MeV}, \\ m(\Xi_{c}(2939)^{0}) = 2938.5 \pm 0.9 \pm 2.3 \,\mathrm{MeV}, \\ \Gamma(\Xi_{c}(2923)^{0}) = \phantom{000}4.8 \pm 0.9 \pm 1.5 \,\mathrm{MeV},\\ \Gamma(\Xi_{c}(2939)^{0}) = \phantom{00}11.0 \pm 1.9 \pm 7.5 \,\mathrm{MeV},$$ where the first uncertainties are statistical and the second systematic. The results are consistent with a previous LHCb measurement using a prompt $\Lambda_{c}^{+} K^{-}$ sample. Evidence of a new $\Xi_{c}(2880)^{0}$ state is found with a local significance of $3.8\,\sigma$, whose mass and width are measured to be $2881.8 \pm 3.1 \pm 8.5\,\mathrm{MeV}$ and $12.4 \pm 5.3 \pm 5.8 \,\mathrm{MeV}$, respectively. In addition, evidence of a new decay mode $\Xi_{c}(2790)^{0} \to \Lambda_{c}^{+} K^{-}$ is found with a significance of $3.7\,\sigma$. The relative branching fraction of $B^{-} \to \Lambda_{c}^{+} \bar{\Lambda}_{c}^{-} K^{-}$ with respect to the $B^{-} \to D^{+} D^{-} K^{-}$ decay is measured to be $2.36 \pm 0.11 \pm 0.22 \pm 0.25$, where the first uncertainty is statistical, the second systematic and the third originates from the branching fractions of charm hadron decays.Comment: All figures and tables, along with any supplementary material and additional information, are available at https://cern.ch/lhcbproject/Publications/p/LHCb-PAPER-2022-028.html (LHCb public pages

Measurement of the ratios of branching fractions R(D∗)\mathcal{R}(D^{*}) and R(D0)\mathcal{R}(D^{0})

The ratios of branching fractions $\mathcal{R}(D^{*})\equiv\mathcal{B}(\bar{B}\to D^{*}\tau^{-}\bar{\nu}_{\tau})/\mathcal{B}(\bar{B}\to D^{*}\mu^{-}\bar{\nu}_{\mu})$ and $\mathcal{R}(D^{0})\equiv\mathcal{B}(B^{-}\to D^{0}\tau^{-}\bar{\nu}_{\tau})/\mathcal{B}(B^{-}\to D^{0}\mu^{-}\bar{\nu}_{\mu})$ are measured, assuming isospin symmetry, using a sample of proton-proton collision data corresponding to 3.0 fb${ }^{-1}$ of integrated luminosity recorded by the LHCb experiment during 2011 and 2012. The tau lepton is identified in the decay mode $\tau^{-}\to\mu^{-}\nu_{\tau}\bar{\nu}_{\mu}$. The measured values are $\mathcal{R}(D^{*})=0.281\pm0.018\pm0.024$ and $\mathcal{R}(D^{0})=0.441\pm0.060\pm0.066$, where the first uncertainty is statistical and the second is systematic. The correlation between these measurements is $\rho=-0.43$. Results are consistent with the current average of these quantities and are at a combined 1.9 standard deviations from the predictions based on lepton flavor universality in the Standard Model.Comment: All figures and tables, along with any supplementary material and additional information, are available at https://cern.ch/lhcbproject/Publications/p/LHCb-PAPER-2022-039.html (LHCb public pages

Observation of the B0 → ρ0ρ0 decay from an amplitude analysis of B0 → (π+π−)(π+π−) decays

Proton–proton collision data recorded in 2011 and 2012 by the LHCb experiment, corresponding to an integrated luminosity of 3.0 fb−1 , are analysed to search for the charmless B0→ρ0ρ0 decay. More than 600 B0→(π+π−)(π+π−) signal decays are selected and used to perform an amplitude analysis, under the assumption of no CP violation in the decay, from which the B0→ρ0ρ0 decay is observed for the first time with 7.1 standard deviations significance. The fraction of B0→ρ0ρ0 decays yielding a longitudinally polarised final state is measured to be fL=0.745−0.058+0.048(stat)±0.034(syst) . The B0→ρ0ρ0 branching fraction, using the B0→ϕK⁎(892)0 decay as reference, is also reported as B(B0→ρ0ρ0)=(0.94±0.17(stat)±0.09(syst)±0.06(BF))×10−6

Measurement of the (eta c)(1S) production cross-section in proton-proton collisions via the decay (eta c)(1S) -&gt; p(p)over-bar

The production of the $\eta_c (1S)$ state in proton-proton collisions is probed via its decay to the $p \bar{p}$ final state with the LHCb detector, in the rapidity range $2.0 6.5$ GeV/c. The cross-section for prompt production of $\eta_c (1S)$ mesons relative to the prompt $J/\psi$ cross-section is measured, for the first time, to be $\sigma_{\eta_c (1S)}/\sigma_{J/\psi} = 1.74 \pm 0.29 \pm 0.28 \pm 0.18 _{B}$ at a centre-of-mass energy $\sqrt{s} = 7$ TeV using data corresponding to an integrated luminosity of 0.7 fb$^{-1}$, and $\sigma_{\eta_c (1S)}/\sigma_{J/\psi} = 1.60 \pm 0.29 \pm 0.25 \pm 0.17 _{B}$ at $\sqrt{s} = 8$ TeV using 2.0 fb$^{-1}$. The uncertainties quoted are, in order, statistical, systematic, and that on the ratio of branching fractions of the $\eta_c (1S)$ and $J/\psi$ decays to the $p \bar{p}$ final state. In addition, the inclusive branching fraction of $b$-hadron decays into $\eta_c (1S)$ mesons is measured, for the first time, to be $B ( b \rightarrow \eta_c X ) = (4.88 \pm 0.64 \pm 0.25 \pm 0.67 _{B}) \times 10^{-3}$, where the third uncertainty includes also the uncertainty on the $J/\psi$ inclusive branching fraction from $b$-hadron decays. The difference between the $J/\psi$ and $\eta_c (1S)$ meson masses is determined to be $114.7 \pm 1.5 \pm 0.1$ MeV/c$^2$.The production of the $\eta _c (1S)$ state in proton-proton collisions is probed via its decay to the $p\overline{p}$ final state with the LHCb detector, in the rapidity range $2.0 6.5 \mathrm{{\,GeV/}{ c}}$ . The cross-section for prompt production of $\eta _c (1S)$ mesons relative to the prompt ${{ J}}/{\psi }$ cross-section is measured, for the first time, to be $\sigma _{\eta _c (1S)}/\sigma _{{{{ J}}/{\psi }}} = 1.74\, \pm \,0.29\, \pm \, 0.28\, \pm \,0.18 _{{\mathcal{B}}}$ at a centre-of-mass energy ${\sqrt{s}} = 7 {~\mathrm{TeV}}$ using data corresponding to an integrated luminosity of 0.7 fb$^{-1}$ , and $\sigma _{\eta _c (1S)}/\sigma _{{{{ J}}/{\psi }}} = 1.60 \pm 0.29 \pm 0.25 \pm 0.17 _{{\mathcal{B}}}$ at ${\sqrt{s}} = 8 {~\mathrm{TeV}}$ using 2.0 fb$^{-1}$ . The uncertainties quoted are, in order, statistical, systematic, and that on the ratio of branching fractions of the $\eta _c (1S)$ and ${{ J}}/{\psi }$ decays to the $p\overline{p}$ final state. In addition, the inclusive branching fraction of ${b}$ -hadron decays into $\eta _c (1S)$ mesons is measured, for the first time, to be ${\mathcal{B}}( b {\rightarrow } \eta _c X ) = (4.88\, \pm \,0.64\, \pm \,0.29\, \pm \, 0.67 _{{\mathcal{B}}}) \times 10^{-3}$ , where the third uncertainty includes also the uncertainty on the ${{ J}}/{\psi }$ inclusive branching fraction from ${b}$ -hadron decays. The difference between the ${{ J}}/{\psi }$ and $\eta _c (1S)$ meson masses is determined to be $114.7 \pm 1.5 \pm 0.1 {\mathrm {\,MeV\!/}c^2}$ .The production of the $\eta_c (1S)$ state in proton-proton collisions is probed via its decay to the $p \bar{p}$ final state with the LHCb detector, in the rapidity range $2.0 6.5$ GeV/c. The cross-section for prompt production of $\eta_c (1S)$ mesons relative to the prompt $J/\psi$ cross-section is measured, for the first time, to be $\sigma_{\eta_c (1S)}/\sigma_{J/\psi} = 1.74 \pm 0.29 \pm 0.28 \pm 0.18 _{B}$ at a centre-of-mass energy $\sqrt{s} = 7$ TeV using data corresponding to an integrated luminosity of 0.7 fb$^{-1}$, and $\sigma_{\eta_c (1S)}/\sigma_{J/\psi} = 1.60 \pm 0.29 \pm 0.25 \pm 0.17 _{B}$ at $\sqrt{s} = 8$ TeV using 2.0 fb$^{-1}$. The uncertainties quoted are, in order, statistical, systematic, and that on the ratio of branching fractions of the $\eta_c (1S)$ and $J/\psi$ decays to the $p \bar{p}$ final state. In addition, the inclusive branching fraction of $b$-hadron decays into $\eta_c (1S)$ mesons is measured, for the first time, to be $B ( b \rightarrow \eta_c X ) = (4.88 \pm 0.64 \pm 0.29 \pm 0.67 _{B}) \times 10^{-3}$, where the third uncertainty includes also the uncertainty on the $J/\psi$ inclusive branching fraction from $b$-hadron decays. The difference between the $J/\psi$ and $\eta_c (1S)$ meson masses is determined to be $114.7 \pm 1.5 \pm 0.1$ MeV/c$^2$