42,326 research outputs found
Analytical considerations of flow boiling heat transfer in metal-foam filled tubes
Flow boiling in metal-foam filled tube was analytically investigated based on a modified microstructure model, an original boiling heat transfer model and fin analysis for metal foams. Microstructure model of metal foams was established, by which fiber diameter and surface area density were precisely predicted. The heat transfer model for flow boiling in metal foams was based on annular pattern, in which two phase fluid was composed by vapor region in the center of the tube and liquid region near the wall. However, it was assumed that nucleate boiling performed only in the liquid region. Fin analysis and heat transfer network for metal foams were integrated to obtain the convective heat transfer coefficient at interface. The analytical solution was verified by its good agreement with experimental data. The parametric study on heat transfer coefficient and boiling mechanism was also carried out
Recommended from our members
Three-dimensional simulation of a new cooling strategy for proton exchange membrane fuel cell stack using a non-isothermal multiphase model
In this study, a new cooling strategy for a proton exchange membrane (PEM) fuel cell stack is investigated using a three-dimensional (3D) multiphase non-isothermal model. The new cooling strategy follows that of the Honda's Clarity design and further extends to a cooling unit every five cells in stacks. The stack consists of 5 fuel cells sharing the inlet and outlet manifolds for reactant gas flows. Each cell has 7-path serpentine flow fields with a counter-flow configuration arranged for hydrogen and air streams. The coolant flow fields are set at the two sides of the stack and are simplified as the convective heat transfer thermal boundary conditions. This study also compares two thermal boundary conditions, namely limited and infinite coolant flow rates, and their impacts on the distributions of oxygen, liquid water, current density and membrane hydration. The difference of local temperature between these two cooling conditions is as much as 6.9 K in the 5-cell stack, while it is only 1.7 K in a single cell. In addition, the increased vapor concentration at high temperature (and hence water saturation pressure) dilutes the oxygen content in the air flow, reducing local oxygen concentration. The higher temperature in the stack also causes low membrane hydration, and consequently poor cell performance and non-uniform current density distribution, as disclosed by the simulation. The work indicates the new cooling strategy can be optimized by increasing the heat transfer coefficient between the stack and coolant to mitigate local overheating and cell performance reduction
Differential quadrature method for space-fractional diffusion equations on 2D irregular domains
In mathematical physics, the space-fractional diffusion equations are of
particular interest in the studies of physical phenomena modelled by L\'{e}vy
processes, which are sometimes called super-diffusion equations. In this
article, we develop the differential quadrature (DQ) methods for solving the 2D
space-fractional diffusion equations on irregular domains. The methods in
presence reduce the original equation into a set of ordinary differential
equations (ODEs) by introducing valid DQ formulations to fractional directional
derivatives based on the functional values at scattered nodal points on problem
domain. The required weighted coefficients are calculated by using radial basis
functions (RBFs) as trial functions, and the resultant ODEs are discretized by
the Crank-Nicolson scheme. The main advantages of our methods lie in their
flexibility and applicability to arbitrary domains. A series of illustrated
examples are finally provided to support these points.Comment: 25 pages, 25 figures, 7 table
Non-linear analytical model for FRCM coupons in tension
Externally bonded FRCM (Fiber Reinforced Cementitious Matrix) materials are nowadays quite diffused to reinforce existing structures: taking as reference FRP (Fiber Reinforced Polymer), the replacement of an organic matrix with mortar is more compatible with masonry substrates, and the reversibility of the reinforcement is more appealing for the architectural heritage conservation. At the same time, due to the low strength of the mortar layers, complex failure mechanisms are observed for FRCMs, which still need comprehensive theoretical investigations. Indeed, not only the mortar-fiber interface may behave non-linearly, but also the mortar may crack and affect the overall behavior. The tensile test on coupons is commonly used as a direct approach to characterize the properties of the reinforcing package, and there is a wide consensus on approximating the global behavior with a trilinear law; however, the different test set-ups and the inhomogeneity of the material itself bring about large dispersion of the experimental results. This paper aims at proposing a simplified analytical model to consider the damage mechanisms in FRCM coupons in tension, including interface slippage, mortar cracking, and their simultaneous occurrence. The accuracy of the model is then verified by comparing the results with experimental data. The conditions under which such failure mechanisms occur and the effects of material properties are also investigated with a view to complement the understanding of experimental observations from a theoretical perspective
A Simplified Analytical Model for FRP-Strengthened Curved Brittle Substrates Using the Multi-Linear Bond-Slip Law
The utilization of fiber-reinforced polymer (FRP) composites for building reinforcement has gained widespread acceptance. However, the bond behavior between externally applied composites and strengthened substrates, which are crucial for system efficacy, has primarily focused on flat surfaces. Yet, the challenge of curved substrates, common in masonry arches and vaults, remains less explored. This study introduces a classical analytical model addressing the bond behavior between FRP plates and curved substrates. This classical approach is structured upon a simplified model that concentrates all the non-linearities of the FRP–substrate interface. The interface is described through a universal multi-linear stress–slip relationship, with the influence of the curved substrate being considered by the normal stress that impacts the interface law. Closed-form solutions for distinct bond-slip law stages are derived and verified against the previous study. Through comparisons with existing experimental data and simulations, this approach is able to predict the maximum load, the trends of the global load-slip curves, and give insights into detailed local behavior. Additionally, the exploration of employing neural networks for determining the interface law exhibits promising outcomes
A Novel FastICA Method for the Reference-based Contrast Functions
This paper deals with the efficient optimization problem of Cumulant-based contrast criteria in the Blind Source Separation (BSS) framework, in which sources are retrieved by maximizing the Kurtosis contrast function. Combined with the recently proposed reference-based contrast schemes, a new fast fixed-point (FastICA) algorithm is proposed for the case of linear and instantaneous mixture. Due to its quadratic dependence on the number of searched parameters, the main advantage of this new method consists in the significant decrement of computational speed, which is particularly striking with large number of samples. The method is essentially similar to the classical algorithm based on the Kurtosis contrast function, but differs in the fact that the reference-based idea is utilized. The validity of this new method was demonstrated by simulations
An Efficient Algorithm by Kurtosis Maximization in Reference-Based Framework
This paper deals with the optimization of kurtosis for complex-valued signals in the independent component analysis (ICA) framework, where source signals are linearly and instantaneously mixed. Inspired by the recently proposed reference-based contrast schemes, a similar contrast function is put forward, based on which a new fast fixed-point (FastICA) algorithm is proposed. The new optimization method is similar in spirit to the former classical kurtosis-based FastICA algorithm but differs in the fact that it is much more efficient than the latter in terms of computational speed, which is significantly striking with large number of samples. The performance of this new algorithm is confirmed through computer simulations
A novel fast and low-cost masonry monitoring strategy and application on arches
This work proposes a novel non-destructive, vision-based measurement strategy to identify and quantify mechanical deformations between rigid blocks. First the possible motions between two rigid blocks were identified and measured, under the application of a perpendicular, parallel and symmetrical 4x4 point grid around the masonry joint line. Repeated calculations of lengths, dot products, and right triangles improved the precision of measurements through redundancy. Then, this method was verified via photographic images with defined deformation and 2D holography, showing good adaptability and precision. Finally, this strategy was performed to a video recording of an arch under tilting test until failure. With the dimensions of the points grid being the only known parameter, the mechanical joint, the type of rigid block motion, the failure point and the rotation angle were successfully determined
- …