Environmental effects on polymeric matrix composites

Current epoxy resins utilized in high performance structural composites absorb moisture from high humidity environments. Such moisture absorption causes plasticization of the resin to occur with concurrent swelling and lowering of the glass transition temperature. Similar effects are observed in composites. Data are presented showing the effects of absorbed moisture on Hercules AS/3501-5 graphite/epoxy composites. Prediction of moisture content and distribution in composites, along with reduction in mechanical properties, are discussed

Notch strength of composites

The notch strength of composites is discussed. The point stress and average stress criteria relate the notched strength of a laminate to the average strength of a relatively long tensile coupon. Tests of notched specimens in which microstrain gages have been placed at or near the edges of the holes have measured strains much larger that those measured in an unnotched tensile coupon. Orthotropic stress concentration analyses of failed notched laminates have also indicated that failure occurred at strains much larger than those experienced on tensile coupons with normal gage lengths. This suggests that the high strains at the edge of a hole can be related to the very short length of fiber subjected to these strains. Lockheed has attempted to correlate a series of tests of several laminates with holes ranging from 0.19 to 0.50 in. Although the average stress criterion correlated well with test results for hole sizes equal to or greater than 0.50 in., it over-estimated the laminate strength in the range of hole sizes from 0.19 to 0.38 in. It thus appears that a theory is needed that is based on the mechanics of failure and is more generally applicable to the range of hole sizes and the varieties of laminates found in aircraft construction

Berry phase in a non-isolated system

We investigate the effect of the environment on a Berry phase measurement involving a spin-half. We model the spin+environment using a biased spin-boson Hamiltonian with a time-dependent magnetic field. We find that, contrary to naive expectations, the Berry phase acquired by the spin can be observed, but only on timescales which are neither too short nor very long. However this Berry phase is not the same as for the isolated spin-half. It does not have a simple geometric interpretation in terms of the adiabatic evolution of either bare spin-states or the dressed spin-resonances that remain once we have traced out the environment. This result is crucial for proposed Berry phase measurements in superconducting nanocircuits as dissipation there is known to be significant.Comment: 4 pages (revTeX4) 2 fig. This version has MAJOR changes to equation

Scout motor performance analysis and prediction study /PAPS/

Scout motor performance analysis and predictio

Cold-air investigation of a 4 1/2 stage turbine with stage-loading factor of 4.66 and high specific work output. 2: Stage group performance

The stage group performance of a 4 1/2 stage turbine with an average stage loading factor of 4.66 and high specific work output was determined in cold air at design equivalent speed. The four stage turbine configuration produced design equivalent work output with an efficiency of 0.856; a barely discernible difference from the 0.855 obtained for the complete 4 1/2 stage turbine in a previous investigation. The turbine was designed and the procedure embodied the following design features: (1) controlled vortex flow, (2) tailored radial work distribution, and (3) control of the location of the boundary-layer transition point on the airfoil suction surface. The efficiency forecast for the 4 1/2 stage turbine was 0.886, and the value predicted using a reference method was 0.862. The stage group performance results were used to determine the individual stage efficiencies for the condition at which design 4 1/2 stage work output was obtained. The efficiencies of stages one and four were about 0.020 lower than the predicted value, that of stage two was 0.014 lower, and that of stage three was about equal to the predicted value. Thus all the stages operated reasonably close to their expected performance levels, and the overall (4 1/2 stage) performance was not degraded by any particularly inefficient component

Low Temperature Physics

Contains reports on one research project

Herschel Observations of a Newly Discovered UX Ori Star in the Large Magellanic Cloud

The LMC star, SSTISAGE1C J050756.44-703453.9, was first noticed during a survey of EROS-2 lightcurves for stars with large irregular brightness variations typical of the R Coronae Borealis (RCB) class. However, the visible spectrum showing emission lines including the Balmer and Paschen series as well as many Fe II lines is emphatically not that of an RCB star. This star has all of the characteristics of a typical UX Ori star. It has a spectral type of approximately A2 and has excited an H II region in its vicinity. However, if it is an LMC member, then it is very luminous for a Herbig Ae/Be star. It shows irregular drops in brightness of up to 2 mag, and displays the reddening and "blueing" typical of this class of stars. Its spectrum, showing a combination of emission and absorption lines, is typical of a UX Ori star that is in a decline caused by obscuration from the circumstellar dust. SSTISAGE1C J050756.44-703453.9 has a strong IR excess and significant emission is present out to 500 micron. Monte Carlo radiative transfer modeling of the SED requires that SSTISAGE1C J050756.44-703453.9 has both a dusty disk as well as a large extended diffuse envelope to fit both the mid- and far-IR dust emission. This star is a new member of the UX Ori subclass of the Herbig Ae/Be stars and only the second such star to be discovered in the LMC.Comment: ApJ, in press. 9 pages, 5 figure