Acoustic and aerodynamic performance of a 1.83 meter (6 foot) diameter 1.2 pressure ratio fan (QF-6)

A 1.2-pressure-ratio, 1.83-meter-(6-ft-) diameter experimental fan stage with characteristics suitable for use in STOL aircraft engines was tested for acoustic and aerodynamic performance. The design incorporated features for low noise, including absence of inlet guide vanes, low rotor-blade-tip speed, low aerodynamic blade loading, and long axial spacing between the rotor and stator rows. The stage was run with four nozzles of different area. The perceived noise along a 152.4 meter (500-ft) sideline was rear-quadrant dominated with a maximum design-point level of 103.9 PNdb. The acoustic 1/3-octave results were analytically separated into broadband and pure-tone components. It was found that the stage noise levels generally increase with a decrease in nozzle area, with this increase observed primarily in the broadband noise component. A stall condition was documented acoustically with a 90-percent-of-design-area nozzle

Aerodynamic and acoustic effects of eliminating core swirl from a full scale 1.6 stage pressure ratio fan (QF-5A)

Fan QF-5A was a modification of fan QF-5 which had an additional core stator and adjusted support struts to turn the core exit flow from a 30 deg swirl to the axial direction. This modification was necessary to eliminate the impingement of the swirling core flow on the axial support pylon of the NASA-Lewis Quiet Fan Facility that caused aerodynamic, acoustic and structural problems with the original fan stage at fan speeds greater than 85 percent of design. The redesigned fan QF-5A did obtain the design bypass ratio with an increased core airflow suggesting that the flow problem was resolved. Acoustically, the redesigned stage showed a low frequency broadband noise reduction compared to the results for fan QF-5 at similar operating conditions

Noise of fan designed to reduce stator lift fluctuations

An existing fan stage was redesigned to reduce stator lift fluctuations and was acoustically tested at three nozzle sizes for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator cord, adjusting incidence angles, and adjusting the rotor velocity diagrams. Broadband noise levels were signficantly reduced in the middle to high frequencies. Blade passage tone sound power was not lessened, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained

Thrombotic variables and risk of idiopathic venous thromboembolism in women aged 45-64 years - Relationships to hormone replacement therapy

Hormone replacement therapy (HRT) has been shown to increase the relative risk of idiopathic venous thromboembolism (VTE) about threefold in several observational studies and one randomised controlled trial. Whether or not this relative risk is higher in women with underlying thrombophilia phenotypes, such as activated protein C (APC) resistance, is unknown. We therefore restudied the participants in a case-control study of the relationship between the use of HRT and the occurrence of idiopathic VTE in women aged 45-64 years. After protocol exclusions, 66 of the cases in the original study and 163 of the controls were studied. Twenty haematological variables relevant to risk of VTE were analysed, including thrombotic states defined from the literature. The relative risk of VTE showed significant associations with APC resistance (OR 4.06; 95% CI 1.62, 10.21); low antithrombin (3.33; 1.15, 9.65) or protein C (2.93; 1.06, 8.14); and high coagulation factor IX (2.34: 1.26, 1.35), or fibrin D-dimer (3.84; 1.99, 7.32). HRT use increased the risk of VTE in women without any of these thrombotic static; (OR 4.09; 95% CI 1.26, 13.30). A similar effect of HRT use on the relative risk of VTE was also found in women with prothrombotic states. Thus for example, the combination of HRT use and APC resistance increased the risk of VTE about 13-fold compared with women of similar age without either APC resistance or HRT use (OR 13.27; 95%, CI 4.30, 40.97). We conclude that the combination of HRT use and thrombophilias (especially if multiple) increases the relative risk of VTE substantially; hence women known to have thrombophilias (especially if multiple) should be counselled about this increased risk prior to prescription of HRT. However. HRT increases the risk of VTE about fourfold even in women without any thrombotic abnormalities: possible causes are discussed

Direct calculation of interfacial tensions from computer simulation: Results for freely jointed tangent hard sphere chains

We develop a methodology for the calculation of surface free energies based on the probability distribution of a wandering interface. Using a simple extension of the NpT sampling, we allow the interface area to randomly probe the available space and evaluate the surface free energy from histogram analysis and the corresponding average. The method is suitable for studying systems with either continuous or discontinuous potentials, as it does not require explicit evaluation of the virial. The proposed algorithm is compared with known results for the surface tension of Lennard--Jones and Square Well fluid, as well as for the interface tension of a bead--spring polymer model and good agreement is found. We also calculate interfacial tensions of freely jointed tangent hard sphere chains on athermal walls for a wide range of chain lengths and densities. The results are compared with three different theoretical approaches, Scaled Particle Theory, the Yu and Wu density functional theory and an analytical approximation based on the latter approach. Whereas SPT only yields qualitative results, the last two approaches are found to yield very good agreement with simulations.Comment: 20 pages, 6 figures, Phys. Rev. E in press

HRTEM study of a new non-stoichiometric BaTiO(3-δ) structure

BaTiO3-based multilayer ceramic capacitors (MLCCs) with Ni internal electrodes are co-fired in reducing atmospheres to avoid oxidation of the electrode. Although dielectric materials are doped by acceptor, donor and amphoteric dopants to minimize the oxygen vacancy content, there is still a large concentration of oxygen vacancies that are accommodated in the BaTiO3 active layers. In general, ABO3 perovskites demonstrates a strong ability to accommodate the oxygen vacancies and maintain a regular pseudo-cubic structure. Oxygen deficient barium titanate can be transformed to a hexagonal polymorph (h-BT) at high temperatures1,2. In this paper, we report the new modulated and long range ordered structures of non-stoichiometric BaTiO3-δ that are observed in the electrically degraded Ni-BaTiO3 MLCCs at low temperature

Implementation of a Standardized Handoff System for a General Surgery Residency Program

Introduction: The I-PASS Handoff Bundle is an evidence based standardized set of educational materials designed to decrease handoff failures in patient care. Two of every three sentinel events , the most serious events reported to the Joint Commission, are due to failures of communication, including miscommunication during patient care handoffs. Implementation of the I-PASS method results in decreased medical errors and preventable adverse events There are few studies that evaluate this validated method in the context of a General Surgery resident program We aim to implement the I-PASS system into the transition of care process for General Surgery residents at our institution, and to analyze of the quality of the handoff process before and after the implementation.https://jdc.jefferson.edu/patientsafetyposters/1047/thumbnail.jp

Can neutron electromagnetic form factors be obtained by polarized inclusive electron scattering off polarized three-nucleon bound states?

The investigation of the electromagnetic inclusive responses of polarized $^{3}$He within the plane wave impulse approximation is briefly reported. A particular emphasys is put on the extraction, from the inclusive responses at the quasielastic peak, of the neutron form factors from feasible experiments.Comment: 6 pages, Latex, 4 Postscript figures. Presented to XVth Conference on "Few-body problems in Physics", Groningen July 1997.To appear in Nucl. Phys.

Aeroacoustic Analysis of Fan Noise Reduction With Increased Bypass Nozzle Area

An advanced model turbofan was tested in the NASA Glenn 9-by 15-Foot Low Speed Wind Tunnel (9x15 LSWT) to explore far field acoustic effects of increased bypass nozzle area. This fan stage test was part of the NASA Glenn Fan Broadband Source Diagnostic Test, second entry (SDT2) which acquired aeroacoustic results over a range of test conditions. The baseline nozzle was sized to produce maximum stage performance at cruise condition. However, the wind tunnel testing is conducted near sea level condition. Therefore, in order to simulate and obtain performance at other operating conditions, two additional nozzles were designed and tested one with +5 percent increase in weight flow (+5.4 percent increase in nozzle area compared with the baseline nozzle), sized to simulate the performance at the stage design point (takeoff) condition, and the other with a +7.5 percent increase in weight flow (+10.9 percent increase in nozzle area) sized for maximum weight flow with a fixed nozzle at sea level condition. Measured acoustic benefits with increased nozzle area were very encouraging, showing overall sound power level (OAPWL) reductions of 2 or more dB while the stage thrust actually increased by 2 to 3 percent except for the most open nozzle at takeoff rotor speed where stage performance decreased. Effective perceived noise levels for a 1500 ft engine flyover and 3.35 scale factor showed a similar noise reduction of 2 or more EPNdB. Noise reductions, principally in the level of broadband noise, were observed everywhere in the far field. Laser Doppler Velocimetry measurements taken downstream of the rotor showed that the total turbulent velocity decreased with increasing nozzle flow, which may explain the reduced rotor broadband noise levels

High-Fidelity Piezoelectric Audio Device

ModalMax is a very innovative means of harnessing the vibration of a piezoelectric actuator to produce an energy efficient low-profile device with high-bandwidth high-fidelity audio response. The piezoelectric audio device outperforms many commercially available speakers made using speaker cones. The piezoelectric device weighs substantially less (4 g) than the speaker cones which use magnets (10 g). ModalMax devices have extreme fabrication simplicity. The entire audio device is fabricated by lamination. The simplicity of the design lends itself to lower cost. The piezoelectric audio device can be used without its acoustic chambers and thereby resulting in a very low thickness of 0.023 in. (0.58 mm). The piezoelectric audio device can be completely encapsulated, which makes it very attractive for use in wet environments. Encapsulation does not significantly alter the audio response. Its small size (see Figure 1) is applicable to many consumer electronic products, such as pagers, portable radios, headphones, laptop computers, computer monitors, toys, and electronic games. The audio device can also be used in automobile or aircraft sound systems