Fatigue failure load indicator

An indicator for recording the load at which a fatigue specimen breaks during the last cycle of a fatigue test is described. A load cell is attached to the specimen which is alternately subjected to tension and compression loads. The output of the load cell which is proportional to the load on the specimen is applied to the input of a peak detector. Each time the specimen is subjected to a compression load, means are provided for applying a positive voltage to the rest of the peak detector to reset it. During the last cycle of the tension load the peak detector measures the maximum load on the specimen. Means are provided for disconnecting the load cell from the peak detector when there is a failure in the specimen

C.V.D. annual report: November 1965 research project RU27-1 :an analogue method for the determination of potential distributions in semiconductor systems

A general method for the solution of the nonlinear Shockley-Poisson differential equation which governs the potential distribution in non-degenerate semiconductor systems is described which can be applied to the evaluation of depletion layer widths, carrier densities and capacitance bias relationships of p-n junction structures. The method is based upon the use of a particular type of resistance network analogue and results obtained for several one and two dimensional configurations are discussed

Analysis of potential helicopter vibration reduction concepts

Results of analytical investigations to develop, understand, and evaluate potential helicopter vibration reduction concepts are presented in the following areas: identification of the fundamental sources of vibratory loads, blade design for low vibration, application of design optimization techniques, active higher harmonic control, blade appended aeromechanical devices, and the prediction of vibratory airloads. Primary sources of vibration are identified for a selected four-bladed articulated rotor operating in high speed level flight. The application of analytical design procedures and optimization techniques are shown to have the potential for establishing reduced vibration blade designs through variations in blade mass and stiffness distributions, and chordwise center-of-gravity location

A model for computing infrared transmission through atmospheric water vapor and carbon dioxide

Model for computing infrared transmission through atmospheric water vapor and carbon dioxid

Calibration of Hewlett-Packard network analyzers: A precision viewpoint

Alternative calibration procedures are examined for Hewlett-Packard vector network analyzers which lead to an improved open-circuit capacitance model, and hence, higher measurement accuracy

A study to examine the feasibility of using surface penetrators for mineral exploration

The feasibility of using penetrators in earth applications is examined. Penetrator applications in exploration for mineral resources only is summarized. Instrumentation for future penetrators is described. Portions of this report are incorporated into a more extensive report examining other penetrator applications in exploration for fossil fuels, geothermal resources, and in environmental and engineering problems, which is to be published as a NASA technical publication

On the Uniqueness of Solution of Magnetostatic Vector‐potential Problems by Three‐dimensional Finite‐element Methods

In this paper, particular attention is paid to the impact of finite‐element approximation on uniqueness and to approximations implicit in finite element formulations from the uniqueness requirements standpoint. It is also shown that the flux density is unique without qualifications. The theoretical and numerical uniqueness of the magnetic vector potential in three‐dimensional problems is also given. This analysis is restricted to linear, isotropic media with Dirichlet Boundary conditions. As an interesting consequence of this analysis it is shown that, under usual conditions adopted in obtaining three‐dimensional finite‐element solutions, it is not necessary to specify div Ā in order that Ā be uniquely defined

Effects of heat input rates on T-1 and T-1A steel welds

Technology of T-1 and T-1A steels is emphasized in investigation of their weld-fabrication. Welding heat input rate, production weldment circumstances, and standards of welding control are considered

Classical Region of a Trapped Bose Gas

The classical region of a Bose gas consists of all single-particle modes that have a high average occupation and are well-described by a classical field. Highly-occupied modes only occur in massive Bose gases at ultra-cold temperatures, in contrast to the photon case where there are highly-occupied modes at all temperatures. For the Bose gas the number of these modes is dependent on the temperature, the total number of particles and their interaction strength. In this paper we characterize the classical region of a harmonically trapped Bose gas over a wide parameter regime. We use a Hartree-Fock approach to account for the effects of interactions, which we observe to significantly change the classical region as compared to the idealized case. We compare our results to full classical field calculations and show that the Hartree-Fock approach provides a qualitatively accurate description of classical region for the interacting gas.Comment: 6 pages, 5 figures; updated to include new results with interaction