1,716 research outputs found
Surface acoustic wave modulation of single photon emission from GaN/InGaN nanowire quantum dots
On-chip quantum information processing requires controllable quantum light
sources that can be operated on-demand at high-speeds and with the possibility
of in-situ control of the photon emission wavelength and its optical
polarization properties. Here, we report on the dynamic control of the optical
emission from core-shell GaN/InGaN nanowire (NW) heterostructures using radio
frequency surface acoustic waves (SAWs). The SAWs are excited on the surface of
a piezoelectric lithium niobate crystal equipped with a SAW delay line onto
which the NWs were mechanically transferred. Luminescent quantum dot (QD)-like
exciton localization centers induced by compositional fluctuations within the
InGaN nanoshell were identified using stroboscopic micro-photoluminescence
(micro-PL) spectroscopy. They exhibit narrow and almost fully linearly
polarized emission lines in the micro-PL spectra and a pronounced anti-bunching
signature of single photon emission in the photon correlation experiments. When
the nanowire is perturbed by the propagating SAW, the embedded QD is
periodically strained and its excitonic transitions are modulated by the
acousto-mechanical coupling, giving rise to a spectral fine-tuning within a
~1.5 meV bandwidth at the acoustic frequency of ~330 MHz. This outcome can be
further combined with spectral detection filtering for temporal control of the
emitted photons. The effect of the SAW piezoelectric field on the QD charge
population and on the optical polarization degree is also observed. The
advantage of the acousto-optoelectric over other control schemes is that it
allows in-situ manipulation of the optical emission properties over a wide
frequency range (up to GHz frequencies).Comment: arXiv admin note: text overlap with arXiv:1902.0791
Resonant inelastic x-ray scattering probes the electron-phonon coupling in the spin-liquid kappa-(BEDT-TTF)2Cu2(CN)3
Resonant inelastic x-ray scattering at the N K edge reveals clearly resolved
harmonics of the anion plane vibrations in the kappa-(BEDT-TTF)2Cu2(CN)3
spin-liquid insulator. Tuning the incoming light energy at the K edge of two
distinct N sites permits to excite different sets of phonon modes. Cyanide CN
stretching mode is selected at the edge of the ordered N sites which are more
strongly connected to the BEDT-TTF molecules, while positionally disordered N
sites show multi-mode excitation. Combining measurements with calculations on
an anion plane cluster permits to estimate the sitedependent electron-phonon
coupling of the modes related to nitrogen excitation
n-Si/SiGe quantum cascade structures for THz emission
In this work we report on modelling the electron transport in n-Si/SiGe structures. The
electronic structure is calculated within the effective-mass complex-energy framework,
separately for perpendicular (Xz) and in-plane (Xxy) valleys, the degeneracy of which is
lifted by strain, and additionally by size quantization. The transport is described via
scattering between quantized states, using the rate equations approach and tight-binding
expansion, taking the coupling with two nearest-neighbour periods. The acoustic phonon,
optical phonon, alloy and interface roughness scattering are taken in the model. The
calculated U/I dependence and gain profiles are presented for a couple of QC structures
Carbide Type Influence on Tribological Properties of Hard Faced Steel Layer - Part I - Theoretical Considerations
This paper gives a theoretical review of influence of the most important alloying elements on steel, and review of the most important carbide-forming elements and states the conditions which elements should fulfill in order to be considered as carbide-forming. It primarily involves alloying elements which in the iron-carbon system can form simple, complex or special carbides, i.e. phases of interstitial and substitutive type. It also gives a review of carbide types that are formed during either production or reparatory hard facing of steel parts with different types of filler materials
Carbide Type Influence on Tribological Properties of Hard Faced Steel Layer Part II- Experimental Results
In this paper is presented a preceding procedure that should be conducted in order to successfully regenerate damaged forging dies by the hard facing process. After the tool damage types identification, as well as their causes, we have chosen the procedure and the parameters of hard facing that we further corrected by conducting the test hard facings on models. Thus, we were able to relate the experimental results outputs with the repair technology, taking as a criterion the quality of the surface layers wear resistance such as friction coefficient and width of hard faced zone, hardness and its distribution in cross section, then microstructure of characteristic of hard faced zones, etc. This research points out significancy of tribological properties of certain types of carbides and their effects on metal matrix, in which carbides are embedded. Our tribological investigations have shown that the working life of the hard faced tool can be longer than that of the new tool
Reparatory and Manufacturing Hard-Facing of Working Parts Made of Stainless Steels in Confectionary Industry
In this paper, for the sake of improving the reparatory hard-facing technology is especially analyzed reparatory hard-facing of tools for manufacturing compressed products in confectionary industry. Those products are being made of a mixture consisting of several powdery components, which is compressed under high pressure. In that way the connection between particles is realized, thus achieving certain hardness and strength of the confectionary product. The considered tool is made of high-alloyed stainless steel. The tool contains 30 identical working places. Besides the production process wear, on those tools, from time to time, appear mechanical damage on some of the products' shape punches, as cracks at the edges, where the products' final shapes are formed. Those damages are small, size wise, but they cause strong effect on the products' final shape. The aggravating circumstance is that the shape punch is extremely loaded in pressure, thus after the reparatory hard-facing, the additional heat treatment is necessary. Mechanical properties in the heat affected zone (HAZ) are being leveled by annealing and what also partially reduces the residual internal stresses
- …