Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V

Recent research on the additive manufacturing (AM) of Ti alloys has shown that the mechanical properties of the parts are affected by the characteristic microstructure that originates from the AM process. To understand the effect of the microstructure on the tensile properties, selective laser melted (SLM) Ti–6Al–4V samples built in three different orientations were tensile tested. The investigated samples were near fully dense, in two distinct conditions, as-built and stress relieved. It was found that the build orientation affects the tensile properties, and in particular the ductility of the samples. The mechanical anisotropy of the parts was discussed in relation to the crystallographic texture, phase composition and the predominant fracture mechanisms. Fractography and electron backscatter diffraction (EBSD) results indicate that the predominant fracture mechanism is intergranular fracture present along the grain boundaries and thus provide and explain the typical fracture surface features observed in fracture AM Ti–6Al–4V

Microstructure of Ti-6Al-4V produced by selective laser melting

Ti-6Al-4V is the most widely used titanium alloy. Manufacturing of Ti-6Al-4V components using novel additive processing techniques such as selective laser melting is of great interest. This study focuses on the microstructure characterisation of Ti-6Al-4V components produced by selective laser melting (SLM) with full (Ti-6Al-4V base plate) and partial (Ti-6Al-4V needle-shaped bed) support. The starting material, a plasma atomised powder, and the component products are studied using various microscopy techniques including optical, scanning electron and transmission electron microscopy and electron backscattered diffraction (EBSD). Powder particles are fully dense, possess a spherical shape and are composed of acicular α phase. The as-built material shows oriented acicular martensitic phase with well defined columnar grains. The morphology of martensitic phase and microstructural evolution will be discussed in relation to the SLM processing parameters employed and the different cooling rates experienced by the components

The Influence of Iron in Minimizing the Microstructural Anisotropy of Ti-6Al-4V Produced by Laser Powder-Bed Fusion

There remains a significant challenge in adapting alloys for metal based Additive Manufacturing (AM). Adjusting alloy composition to suit the process, particularly under regimes close to industrial practice, is therefore a potential solution. With the aim of designing new Ti-based alloys of superior mechanical properties for use in laser powder-bed fusion, this research investigates the influence of Fe on the microstructural development of Ti-6Al-4V. The operating mechanisms that govern the relationship between the alloy composition (and Fe in particular) and the grain size are explored using EBSD, TEM and in-situ high-energy synchrotron X-ray diffraction. It was found that Fe additions up to 3 wt% lead to a progressive refinement of the microstructure. By exploiting the cooling rates of AM and suitable amount of Fe additions, it was possible to obtain microstructures that can be optimized by heat treatment without obvious precipitation of detrimental brittle phases. The resulting microstructure consists of a desirable and well studied fully laminar α+ β structure in refined prior-β grains

Microstructure and texture development during solid consolidation recycling of Ti-6Al-4V

Ti-6Al-4V machining chips were recycled using equal channel angular pressing (ECAP). The microstructural and texture evolution of the recycled Ti-6Al-4V have been investigated using scanning electron microscopy, electron backscattered diffraction and transmission electron microscopy. For samples consolidated at 500 °C with a back-pressure of 100 MPa, the as-pressed density reached up to 99.9% after 8 passes. Pronounced grain refinement was also observed with increasing number of passes. The morphology of the grains has been changed from elongated and coarse to equiaxed and ultrafine as the number of passes increases. Strong textures were also introduced during multiple passes via Bc route. Texture has been developed with basal planes parallel to the inclination direction which is at 21° of the extrusion direction. After 4 and 8 passes, basal planes were rotated towards the transverse direction. No oxide can be detected at the chip-chip boundaries when the Ti-Al-4 V machining chips was consolidated at 500 °C. When the sample was processed at 550 °C, significant grain growth and clear oxide layers at the chip-chip interface were observed. In addition, the c-axis were rotated towards the longitudinal direction due to the non-basal slip activity. TEM observation revealed the dislocations presence in the 550 °C ECAP-processed sample

Education in IT Security: A Case Study in Banking Industry

The banking industry has been changing incessantlyand facing new combination of risks. Data protection andcorporate security is now one of the major issues in bankingindustry. As the rapid changing on technologies from time totime, the industry should be aware on new technologies in orderto protect information assets and prevent fraud activities. Thispaper begins with literature study of information security issuesand followed by focused-group interviews with five participantswithin the industry and survey analysis of “The global state ofInformation Security survey 2013” which published byPriceWaterhouseCoopers (PWC). Trends and questions werediscussed as well as possible solution. The study suggests that ITsecurity education should be made to different level of staffs suchas executives, professional and general staffs. Besides, thebanking industry should increase company-wide securityawareness and the importance of corporate security which keepthe information and physical assets secure and in a proper way

Effect of machining on shear-zone microstructure in Ti-15V-3Cr-3Al-3Sn: conventional and ultrasonically assisted turning

This work systematically studied morphology of nano- and microstructures in primary and secondary shear zones of machining chips produced with two different machining methods: conventional and ultrasonically assisted turning. Electron backscatter diffraction and transmission electron microscopy showed that chips had similar microstructures for both machining techniques. The nanostructure in secondary shear zones was less homogeneous than that in primary shear zones. In addition, a heavily deformed layer was formed in a subsurface of Ti-15V-3Cr-3Al-3Sn work-pieces, replicating the microstructure of secondary shear zones of the machining chips, and elongated nanocrystalline grains in this layer were aligned with a tangential direction of turning

Exogenous Expression of Human apoA-I Enhances Cardiac Differentiation of Pluripotent Stem Cells

The cardioprotective effects of high-density lipoprotein cholesterol (HDL-C) and apolipoprotein A1 (apoA-I) are well documented, but their effects in the direction of the cardiac differentiation of embryonic stem cells are unknown. We evaluated the effects of exogenous apoA-I expression on cardiac differentiation of ESCs and maturation of ESC-derived cardiomyocytes. We stably over-expressed full-length human apoA-I cDNA with lentivirus (LV)-mediated gene transfer in undifferentiated mouse ESCs and human induced pluripotent stem cells. Upon cardiac differentiation, we observed a significantly higher percentage of beating embryoid bodies, an increased number of cardiomyocytes as determined by flow cytometry, and expression of cardiac markers including α-myosin heavy chain, β-myosin heavy chain and myosin light chain 2 ventricular transcripts in LV-apoA-I transduced ESCs compared with control (LV-GFP). In the presence of noggin, a BMP4 antagonist, activation of BMP4-SMAD signaling cascade in apoA-I transduced ESCs completely abolished the apoA-I stimulated cardiac differentiation. Furthermore, co-application of recombinant apoA-I and BMP4 synergistically increased the percentage of beating EBs derived from untransduced D3 ESCs. These together suggests that that pro-cardiogenic apoA-I is mediated via the BMP4-SMAD signaling pathway. Functionally, cardiomyocytes derived from the apoA-I-transduced cells exhibited improved calcium handling properties in both non-caffeine and caffeine-induced calcium transient, suggesting that apoA-I plays a role in enhancing cardiac maturation. This increased cardiac differentiation and maturation has also been observed in human iPSCs, providing further evidence of the beneficial effects of apoA-I in promoting cardiac differentiation. In Conclusion, we present novel experimental evidence that apoA-I enhances cardiac differentiation of ESCs and iPSCs and promotes maturation of the calcium handling property of ESC-derived cardiomyocytes via the BMP4/SMAD signaling pathway

The influence of iron in minimizing the microstructural anisotropy of Ti-6Al-4V produced by laser powder-bed fusion

There remains a significant challenge in adapting alloys for metal-based additive manufacturing (AM). Adjusting alloy composition to suit the process, particularly under regimes close to industrial practice, is therefore a potential solution. With the aim of designing new Ti-based alloys of superior mechanical properties for use in laser powder-bed fusion, this research investigates the influence of Fe on the microstructural development of Ti-6Al-4V. The operating mechanisms that govern the relationship between the alloy composition (and Fe in particular) and the grain size are explored using EBSD, TEM, and in situ high-energy synchrotron X-ray diffraction. It was found that Fe additions up to 3 wt pct lead to a progressive refinement of the microstructure. By exploiting the cooling rates of AM and suitable amount of Fe additions, it was possible to obtain microstructures that can be optimized by heat treatment without obvious precipitation of detrimental brittle phases. The resulting microstructure consists of a desirable and well-studied fully laminar α + β structure in refined prior-β grains