125,887 research outputs found
Estimation of stiffening effect of shaft and housing material outside projected area of a rolling element bearing
In the analysis of distortions occurring in rolling-element bearings, it is common to neglect the stiffening effect of shafting outside the bearing region. The magnitude of such an effect will be dependent primarily on the bearing width-to-bore ratio, the shaft geometry, and the location of the bearing on the shaft. An estimate is given of the stiffening effect for a wide range of these variables. In addition, brief consideration is given to the parallel situation existing at the outer ring housing
Thermal stress analysis of a graded zirconia/metal gas path seal system for aircraft gas turbine engines
A ceramic/metallic aircraft gas turbine outer gas path seal designed to enable improved engine performance is studied. Flexible numerical analysis schemes suitable for the determination of transient temperature profiles and thermal stress distributions in the seal are outlined. An estimation of the stresses to which a test seal is subjected during simulated engine deceleration from sea level takeoff to idle conditions is made. Experimental evidence has indicated that the surface layer of the seal is probably subjected to excessive tensile stresses during cyclic temperature loading. This assertion is supported by the analytical results presented. Brief consideration is given to means of mitigating this adverse stressing
Elastic distortion of flanged inner ring of high-speed cylindrical roller bearing
The elastic distortion of the inner ring of an experimental roller bearing is investigated analytically. The geometry of the experimental bearing is unusually complex, and for this reason a bearing with an axially symmetric inner ring is also analyzed. Only the inner ring and shaft are considered using a two dimensional finite element program that can accommodate interference between these components. The results suggest that the elastic distortions are modest in relation to the design clearances associated with the experimental bearing. The variation of the radial deflection of the raceway may, however, be significant in some circumstances
Finite-element computer program for axisymmetric loading situations where components may have a relative interference fit
A finite element computer program which enables the analysis of distortions and stresses occurring in compounds having a relative interference is presented. The program is limited to situations in which the loading is axisymmetric. Loads arising from the interference fit(s) and external, inertial, and thermal loadings are accommodated. The components comprise several different homogeneous isotropic materials whose properties may be a function of temperature. An example illustrating the data input and program output is given
Recommended from our members
A vertex-based finite volume method applied to non-linear material problems in computational solid mechanics
A vertex-based finite volume (FV) method is presented for the computational solution of quasi-static solid mechanics problems involving material non-linearity and infinitesimal strains. The problems are analysed numerically with fully unstructured meshes that consist of a variety of two- and three-dimensional element types. A detailed comparison between the vertex-based FV and the standard Galerkin FE methods is provided with regard to discretization, solution accuracy and computational efficiency. For some problem classes a direct equivalence of the two methods is demonstrated, both theoretically and numerically. However, for other problems some interesting advantages and disadvantages of the FV formulation over the Galerkin FE method are highlighted
Temperature distributions and thermal stresses in a graded zirconia/metal gas path seal system for aircraft gas turbine engines
A ceramic/metallic aircraft gas turbine outer gas path seal designed for improved engine performance was studied. Transient temperature and stress profiles in a test seal geometry were determined by numerical analysis. During a simulated engine deceleration cycle from sea-level takeoff to idle conditions, the maximum seal temperature occurred below the seal surface, therefore the top layer of the seal was probably subjected to tensile stresses exceeding the modulus of rupture. In the stress analysis both two- and three-dimensional finite element computer programs were used. Predicted trends of the simpler and more easily usable two-dimensional element programs were borne out by the three-dimensional finite element program results
Proportional-integral-plus (PIP) control of time delay systems
The paper shows that the digital proportional-integral-plus (PIP) controller formulated within the context of non-minimum state space (NMSS) control system design methodology is directly equivalent, under certain non-restrictive pole assignment conditions, to the equivalent digital Smith predictor (SP) control system for time delay systems. This allows SP controllers to be considered within the context of NMSS state variable feedback control, so that optimal design methods can be exploited to enhance the performance of the SP controller. Alternatively, since the PIP design strategy provides a more flexible approach, which subsumes the SP controller as one option, it provides a superior basis for general control system design. The paper also discusses the robustness and disturbance response characteristics of the two PIP control structures that emerge from the analysis and demonstrates the efficacy of the design methods through simulation examples and the design of a climate control system for a large horticultural glasshouse system
Assimilation of MSG land-surface temperature into land-surface model simulations to constrain estimates of surface energy budget in West Africa
In the semi-arid regions of West Africa the surface energy partition is related closely to near surface moisture availability. Such moisture availability exhibits marked heterogeneity at scales of a few kilometres, related to the
passage of storm systems during the previous one or two days. The associated variations in surface fluxes affect planetary boundary layer properties at the mesoscale, which may in turn affect rainfall and the seasonal development of the West African monsoon.
Atmosphere models used to study this land-atmosphere coupling are sensitive to the soil moisture initial condition. There exists no observation network for soil moisture in West Africa, so models rely on data from atmosphere analyses, which are often unable to describe adequately surface variation at the mesoscale. Additionally, retrospective estimates of the seasonal surface energy and water budgets using land-surface models are biased by persistent model errors in soil moisture. Anomalies in near-surface (top few centimetres) soil moisture are anti-correlated with anomalies in land-surface brightness temperature, which is observed by the SEVIRI thermal infra-red sensors onboard the Meteosat Second Generation (MSG) satellites. Here, we present methods developed for assimilating the MSG land-surface temperature product from the Land SAF to constrain estimates of the surface energy and water budgets using the JULES land-surface model. This MSG temperature product has a pixel size of approximately 3 km in this region, and is known to provide information of surface wetness anomalies at the scales of interest. The results will provide, for a large region of West Africa, improved initial conditions for modelling studies and seasonal estimates of the surface energy and water budgets
- …