The impact of loads on standard diameter, small diameter and mini implants: A comparative laboratory study

Objectives: While caution in the use of small-diameter (≤3.5 mm) implants has been advocated in view of an increased risk of fatigue fracture under clinical loading conditions, a variety of implant designs with diameters <3 mm are currently offered in the market for reconstructions including fixed restorations. There is an absence of reported laboratory studies and randomized-controlled clinical trials to demonstrate clinical efficacy for implant designs with small diameters. This laboratory study aimed to provide comparative data on the mechanical performance of a number of narrow commercially marketed implants. Materials and methods: Implants of varying designs were investigated under a standardized test set-up similar to that recommended for standardized ISO laboratory testing. Implant assemblies were mounted in acrylic blocks supporting laboratory cast crowns and subjected to 30° off-axis loading on an LRX Tensometer. Continuous output data were collected using Nexygen software. Results: Load/displacement curves demonstrated good grouping of samples for each design with elastic deformation up to a point of failure approximating the maximum load value for each sample. The maximum loads for Straumann (control) implants were 989 N (±107 N) for the 4.1 mm RN design, and 619 N (±50 N) for the 3.3 mm RN implant (an implant known to have a risk of fracture in clinical use). Values for mini implants were recorded as 261 N (±31 N) for the HiTec 2.4 mm implant, 237 N (±37 N) for the Osteocare 2.8 mm mini and 147 N (±25 N) for the Osteocare mini design. Other implant designs were also tested. Conclusions: The diameters of the commercially available implants tested demonstrated a major impact on their ability to withstand load, with those below 3 mm diameter yielding results significantly below a value representing a risk of fracture in clinical practice. The results therefore advocate caution when considering the applicability of implants ≤3 mm diameter. Standardized fatigue testing is recommended for all commercially available implants

Fuselage structure using advanced technology fiber reinforced composites

A fuselage structure is described in which the skin is comprised of layers of a matrix fiber reinforced composite, with the stringers reinforced with the same composite material. The high strength to weight ratio of the composite, particularly at elevated temperatures, and its high modulus of elasticity, makes it desirable for use in airplane structures

THE PROBLEM OF REGIONAL "HOLLOWING OUT" IN JAPAN : LESSONS FOR REGIONAL INDUSTRIAL POLICY

This paper considers the problems of "hollowing out" using a Case Study of Japan's machinery sector. In doing so, it explores the roots of the present crisis by focusing upon the role played by Japan's large transnational corporations. This is important because these corporations are the "central actors" within the Japanese economy and they control a significant proportion of Japanese manufacturing. It is their strategic decisions - those that determine the level and location of investment, employment and output - which ultimately shape the development path for Japanese industry (see Cowling and Sugden, 1994, 1998). In recent years, Japan’s large transnationals have become engaged in the process of elite globalisation, pursuing their own interests at the expense of domestic Japanese industry. This is a fundamental insight that is crucial for designing appropriate policy responses to arrest Japan's current industrial decline. It is argued that the lessons from Japan's experience might guide policymakers in other regions, such as Wisconsin, who are concerned with future industrial development, the effects of globalisation and problems of "hollowing out".Machinery sector ; strategic-decision making ; strategic failure ; industrial policy.

Doing Something About the Future

This paper is concerned with the need for more interdisciplinary, systems oriented, research directed towards major problems ecountered by decision makers in industry and government; a need which is more difficult to meet in the face of traditional methods of organizing knowledge and research. It emphasizes the need to acknowledge the true complexity of the problems and the interactive nature of any effective research procedure. As an illustration, both of the need and the problems involved in meeting it, the development of a new program of research into problems of Management and Technology at the International Institute of Applied Systems Analysis, which is supported by seventeen nations of all political complexions, is analyzed. The implication is that we can do something about the future but we must be prepared to do

Improvement of Fourier Polarimetry for applications in tomographic photoelasticity

The use of the Fourier Polarimetry method has been demonstrated to extract the three characteristic parameters in integrated photoelasticity. In contrast to the phase-stepping method, it has been shown that the Fourier method is more accurate. However, the Fourier method isn't very efficient as it requires that a minimum of nine intensity images be collected during a whole revolution of a polarizer while the phase-stepping method only needs six intensity images. In this paper the Fourier transformation is used to derive the expression for determination of the characteristic parameters. Four Fourier coefficients are clearly identified to calculate the three characteristic parameters. It is found that the angular rotation ratio could be set arbitrarily. The angular rotation ratio is optimized to satisfy the requirements of efficiency and proper data accuracy, which results in data collection about three times faster than the methods suggested by previous researchers. When comparing their performance in terms of efficiency and accuracy, the simulated and experimental results show that these angular rotation ratios have the same accuracy but the optimized angular rotation ratio is significantly faster. The sensitivity to noise is also investigated and further improvement of accuracy is suggested

Understanding the friction mechanisms between the human finger and flat contacting surfaces in moist conditions

Human hands sweat in different circumstances and the presence of sweat can alter the friction between the hand and contacting surface. It is, therefore, important to understand how hand moisture varies between people, during different activities and the effect of this on friction. In this study, a survey of fingertip moisture was done. Friction tests were then carried out to investigate the effect of moisture. Moisture was added to the surface of the finger, the finger was soaked in water, and water was added to the counter-surface; the friction of the contact was then measured. It was found that the friction increased, up until a certain level of moisture and then decreased. The increase in friction has previously been explained by viscous shearing, water absorption and capillary adhesion. The results from the experiments enabled the mechanisms to be investigated analytically. This study found that water absorption is the principle mechanism responsible for the increase in friction, followed by capillary adhesion, although it was not conclusively proved that this contributes significantly. Both these mechanisms increase friction by increasing the area of contact and therefore adhesion. Viscous shearing in the liquid bridges has negligible effect. There are, however, many limitations in the modelling that need further exploration