17,859 research outputs found
A low sidelobe asymmetric beam antenna for high altitude platform communications
In a communications network served by a high altitude platform, the antenna beams illuminating each cell require minimized sidelobe powers. Asymmetric beams are advantageous so that cell footprints remain circular. At millimeter wavelengths a lens antenna can have the desired properties. We have chosen a 6 km diameter cell at 32 degrees elevation angle and shown how the required beam asymmetry can be implemented using an optimized polynomial for describing the lens profile. The measured average sidelobe level is below -42 dB
Effect of lateral displacement of a high-altitude platform on cellular interference and handover
A method for predicting movements in cellular coverage caused by lateral drift of a high-altitude platform (a quasi-stationary platform in the stratosphere) is developed. Cells are produced by spot beams generated by horn-type antennas on the platform. It is shown how the carrier-to-interference ratio (CIR) across these cells varies when the antenna payload is steered to accommodate the lateral movement of the platform. The geometry of the antenna beam footprint on the ground is first developed and then applied to a system of many cochannel beams. Pointing strategies are examined, where the pointing angle is calculated to keep, for example, a center cell or an edge cell in the same nominal position before and after the platform drift, and the CIR distribution is calculated. It is shown that the optimum pointing angle depends on the desired level of CIR across the service area, typically lying between 3 +/- 0.75 degrees for a platform drift of 2'km and corresponding to a cell in the middle ring. It is shown that it is necessary for a significant proportion of users to perform a handover to maintain a given CIR after platform drift. The analysis reveals that there is an optimum pointing angle that minimizes the probability of handover for a particular value of drift and CIR
Frequency selective lens antenna
A variant of the hemispherical microwave lens antenna is reported where the ground plane region is modified through use of a frequency selective surface. This allows discrimination of frequencies by two closely spaced primary feeds. A scale model is reported operating at 12 and 30 GHz
Recommended from our members
A computer system to perform structure comparison using TOPS representations of protein structure
We describe the design and implementation of a fast topology–based method
for protein structure comparison. The approach uses the TOPS topological representation
of protein structure, aligning two structures using a common discovered
pattern and generating measure of distance derived from an insert score. Heavy
use is made of a constraint-based pattern matching algorithm for TOPS diagrams
that we have designed and described elsewhere Gilbert et al. (1999). The comparison
system is maintained at the European Bioinformatics Institute and is available
over the Web via the at tops.ebi.ac.uk/tops. Users submit a structure description in
Protein Data Bank (PDB) format and can compare it with structures in the entire
PDB or a representative subset of protein domains, receiving the results by email
Recommended from our members
Topology-based protein structure comparison using a pattern discovery technique
Integrated thermal-structural analysis of large space structures
Optimum performance of large space antennas requires very fine control of the shape of the antenna surface since the shape affects both frequency control and pointing accuracy. A significant factor affecting the antenna shape is the temperature of the structure and the resulting deformation. To accurately predict the temperature of the structure, it is necessary first to accurately predict thermal loads. As the structure orbits the Earth, the thermal loads change constantly so that the thermal-structural response varies continuously throughout the orbit. The results from recent applications of integrated finite element methodology to heat load determination and thermal-structural analysis of large space structures are given. Four areas are concentrated on: (1) the characteristics of the integrated finite element methodology, (2) fundamentals of orbital heat load calculation, (3) description and comparison of some radiation finite elements, and (4) application of the integrated finite-element approach to the thermal-structural analysis of an orbiting truss structure
Finite element thermal-structural modeling of orbiting truss structures
A description of an integrated finite element (FE) thermal-structural approach for accurate and efficient modeling of large space structures is presented. A geometric model with a common discretization for all analyses is employed. It uses improved thermal elements and the results from the thermal analysis directly in the structural analysis without any intervening data processing. The differences between the conventional FE approach as implemented in large programs and an integrated FE approach currently under development are described. Considerations for thermal modeling of truss members is discussed and three thermal truss finite elements are presented. The performance of these elements was evaluated for typical truss members neglecting joint effects. A simple truss with metallic joints and composite members was studied to evaluate the effectiveness of the approach for realistic truss designs. A study of the effects of aluminum joints on the thermal deformations of a simple, plane truss with composite members showed that joint effects may be significant. Further study is needed to assess the role of joint effects on the deformation of large trusses
Flutter: A finite element program for aerodynamic instability analysis of general shells of revolution with thermal prestress
Documentation for the computer program FLUTTER is presented. The theory of aerodynamic instability with thermal prestress is discussed. Theoretical aspects of the finite element matrices required in the aerodynamic instability analysis are also discussed. General organization of the computer program is explained, and instructions are then presented for the execution of the program
Do bank loan rates exhibit a countercyclical mark-up?
Based on a switching-cost model, we examine empirically the hypotheses that bank loan mark-ups are countercyclical and asymmetric in their responsiveness to recessionary and expansionary impulses. The first econometric model treats changes in the mark-up as a continuous variable. The second treats them as an ordered categorical variable due to the discrete nature of prime rate changes. By allowing the variance to switch over time as a Markov process, we present the first conditionally heteroskedastic discrete choice (ordered probit) model for time-series applications. This feature yields a remarkable improvement in the likelihood function. Specifications that do not account for conditional heteroskedasticity find evidence of both countercyclical and asymmetric mark-up behavior. In contrast, the heteroskedastic ordered probit finds the mark-up to be countercyclical but not significantly asymmetric. We explain why controlling for conditional heteroskedasticity may be important when testing for downward stickiness in loan rates.Bank loans ; Interest rates
- …