Design constraints and higher temperature intermetallic bond coatings

Bond coat interlayers in thermal barrier coating (TBC) systems must perform reliably in the complex thermal, chemical and mechanical environment of the turbine engine. To achieve higher temperatures and /or longer cyclic lives, a spectrum of intrinsic failure modes must be suppressed. Failure may occur at the bond coat – thermally grown oxide (TGO) interface, at the TGO-TBC interface or by oxidation-enhanced propagation of cracks from the coating into the substrate. Models for the failure processes suggest that bond coatings should possess improved high temperature strength (creep resistance), low oxide growth stresses and high interfacial toughnesses. Oxide growth stresses have been measured across a spectrum of bond coat compositions. A new femtosecond laser-based approach to measuring interfacial toughness will be discussed. Finally, the behavior of multilayered intermetallic coatings designed to be thermodynamically compatible with the superalloy substrate under cyclic oxidation conditions will be presented

Multi-layered Ruthenium-modified Bond Coats for Thermal Barrier Coatings

Diffusional approaches for fabrication of multi-layered Ru-modified bond coats for thermal barrier coatings have been developed via low activity chemical vapor deposition and high activity pack aluminization. Both processes yield bond coats comprising two distinct B2 layers, based on NiAl and RuAl, however, the position of these layers relative to the bond coat surface is reversed when switching processes. The structural evolution of each coating at various stages of the fabrication process has been and subsequent cyclic oxidation is presented, and the relevant interdiffusion and phase equilibria issues in are discussed. Evaluation of the oxidation behavior of these Ru-modified bond coat structures reveals that each B2 interlayer arrangement leads to the formation of α-Al 2 O 3 TGO at 1100°C, but the durability of the TGO is somewhat different and in need of further improvement in both cases

Mushy-Zone Rayleigh Number to Describe Macrosegregation and Channel Segregate Formation During Directional Solidification of Metallic Alloys

A recently defined mushy-zone Rayleigh number (R-aM) that includes side-branching contributions to the mushy-zone permeability has been examined for its correlation with the longitudinal macrosegregation and channel segregate formation. The Rayleigh number shows (1) a strong correlation between the extent of longitudinal macrosegregation and increase in the mushy-zone convection and (2) a good ability to predict the formation of channel segregates during directional solidification

Geometric and thermodynamic properties in Gauss-Bonnet gravity

In this paper, the generalized second law (GSL) of thermodynamics and entropy is revisited in the context of cosmological models in Gauss-Bonnet gravity with the boundary of the universe is assumed to be enclosed by the dynamical apparent horizon. The model is best fitted with the observational data for distance modulus. The best fitted geometric and thermodynamic parameters such as equation of state parameter, deceleration parameter and entropy are derived. To link between thermodynamic and geometric parameters, the "entropy rate of change multiplied by the temperature" as a model independent thermodynamic state parameter is also derived. The results show that the model is in good agreement with the observational analysis.Comment: 13 pages, 13 figures, to be published in Astrophysics and Space Sc

Microstructural and Chemical Rejuvenation of a Ni-Based Superalloy

This is an open access article published by Springer and distributed under the terms of the Creative Commons Attribution Licence (CC BY 4.0), http://creativecommons.org/licenses/by/4.0/The microstructural evolution of the Ni-based superalloy CMSX-4 including the change in gamma prime morphology, size and distribution after high temperature degradation and subsequent rejuvenation heat treatments has been examined using field emission gun scanning electron microscopy (FEGSEM) and transmission electron microscopy (TEM). In this paper it is shown that there are significant differences in the size of the ‘channels’ between gamma prime particles, the degree of rafting and the size of tertiary gamma prime particles in each of the different microstructural conditions studied. Chemical analysis has been carried out to compare rejuvenated and pre-service samples after the same subsequent degradation procedure. The results indicate that although the microstructure of pre-service and rejuvenated samples are similar, chemical differences are more pronounced in the rejuvenated samples, suggesting that chemical segregation from partitioning of the elements was not completely eliminated through the applied rejuvenation heat treatment. A number of modified rejuvenation heat treatment trials were carried out to reduce the chemical segregation prior to creep testing. The creep test results suggest that chemical segregation has an immeasurable influence on the short-term mechanical properties under the test conditions used here, indicating that further work is required to fully understand the suitability of specific rejuvenation heat treatments and their role in the extension of component life in power plant applications

Influence of Heat Treatment on Defect Structures in Single-Crystalline Blade Roots Studied by X-ray Topography and Positron Annihilation Lifetime Spectroscopy

Single-crystalline superalloy CMSX-4 is studied in the as-cast state and after heat treatment, with material being taken from turbine blade castings. The effect of the heat treatment on the defect structure of the root area near the selector/root connection is emphasized. Multiscale analysis is performed to correlate results obtained by X-ray topography and positron annihilation lifetime spectroscopy (PALS). Electron microscopy observations were also carried out to characterize the inhomogeneity in dendritic structure. The X-ray topography was used to compare defects of the misorientation nature, occurring in as-cast and treated states. The type and concentration of defects before and after heat treatment in different root areas were determined using the PALS method, which enables voids, mono-vacancies, and dislocations to be taken into account. In this way, differences in the concentration of defects caused by heat treatment are rationalized

Moderate drinking before the unit: medicine and life assurance in Britain and the US c.1860–1930

This article describes the way in which “Anstie’s Limit” – a particular definition of moderate drinking first defined in Britain in the 1860s by the physician Francis Edmund Anstie (1833–1874) – became established as a useful measure of moderate alcohol consumption. Becoming fairly well-established in mainstream Anglophone medicine by 1900, it was also communicated to the public in Britain, North America and New Zealand through newspaper reports. However, the limit also travelled to less familiar places, including life assurance offices, where a number of different strategies for separating moderate from excessive drinkers emerged from the dialogue between medicine and life assurance. Whilst these ideas of moderation seem to have disappeared into the background for much of the twentieth century, re-emerging as the “J-shaped” curve, these early developments anticipate many of the questions surrounding uses of the “unit” to quantify moderate alcohol consumption in Britain today. The article will therefore conclude by exploring some of the lessons of this story for contemporary discussions of moderation, suggesting that we should pay more attention to whether these metrics work, where they work and why

Entropy and statefinder diagnosis in chameleon cosmology

In this paper, the generalized second law (GSL) of thermodynamics and entropy is revisited in the context of cosmological models with bouncing behavior such as chameleon cosmology where the boundary of the universe is assumed to be enclosed by the dynamical apparent horizon. From a thermodynamic point of view, to link between thermodynamic and geometric parameters in cosmological models, we introduce "entropy rate of change multiplied by the temperature" as a model independent thermodynamic state parameter together with the well known $\{r,s \}$ statefinder to differentiate the dark energy models.Comment: 11 pages, 5 figures. will be published in Astrophys. Space Sc