A design procedure for the handling qualities optimization of the X-29A aircraft

A design technique for handling qualities improvement was developed for the X-29A aircraft. As with any new aircraft, the X-29A control law designers were presented with a relatively high degree of uncertainty in their mathematical models. The presence of uncertainties, and the high level of static instability of the X-29A caused the control law designers to stress stability and robustness over handling qualities. During flight test, the mathematical models of the vehicle were validated or corrected to match the vehicle dynamic behavior. The updated models were then used to fine tune the control system to provide fighter-like handling characteristics. A design methodology was developed which works within the existing control system architecture to provide improved handling qualities and acceptable stability with a minimum of cost in both implementation as well as software verification and validation

Ground vibration test results for Drones for Aerodynamic and Structural Testing (DAST)/Aeroelastic Research Wing (ARW-1R) aircraft

The drones for aerodynamic and structural testing (DAST) project was designed to control flutter actively at high subsonic speeds. Accurate knowledge of the structural model was critical for the successful design of the control system. A ground vibration test was conducted on the DAST vehicle to determine the structural model characteristics. This report presents and discusses the vibration and test equipment, the test setup and procedures, and the antisymmetric and symmetric mode shape results. The modal characteristics were subsequently used to update the structural model employed in the control law design process

The Spaceborne Global Climate Observing Center (SGCOC): Executive summary

Conceptual planning of the Spaceborne portion of the Global Climate Observing Systems (SGCOS) is reviewed. Fundamentals of the SGCOS are summarized

Study of the order of the phase transition in pure U(1) gauge theory with Villain action

We address the question of the order of the deconfinement phase transition of four dimensional U(1) lattice gauge theory. Simulations of the Z-gauge theory dual to the Villain action on toroidal lattices up to lattice sizes of 28^4 give results consistent with both, a vanishing and a nonvanishing discontinuity in the thermodynamic limit. A decision on the order of the phase transition requires still larger lattice sizes.Comment: LATTICE98(gauge), 3 pages, 2 figure

New method for critical failure prediction of complex systems

Rigorous analytical technique, called criticality determination methodology /or CD technique/ determines the probability that a given complex system will successfully achieve stated objectives. The CD technique identifies critical elements of the system by a failure mode and effects analysis

HLA-B27 Positivity: associated health implications

HLA-B27 positivity makes the onset of autoimmune diseases such as uveitis, ankylosing spondylitis and Crohn's disease more likely to occur. Ankylosing spondylitis and Crohn's disease are two types of HLA-B27 positive diseases that demonstrate a direct association with uveitis. Although the possession of HLA-B27 positivity is not mandatory for autoimmune diseases such as uveitis to occur, HLA-B27 positivity not only makes it more likely but may modify the clinical picture in which a patient presents. In relation to assessment and diagnosis it is imperative that the medical history of patients is thoroughly examined to ensure pathological sequelae are appropriately treated. Nurses play an important role in assessing patients that have uveitis and should suspect ankylosing spondylitis or Crohn's disease may be present

Research on solar pumped liquid lasers

A solar pumped liquid laser that can be scaled up to high power (10Mw CW) for space applications was developed. Liquid lasers have the inherent advantage over gases in that they provide much higher lasant densities and thus high power densities. Liquids also have inherent advantages over solids in that they have much higher damage thresholds and are much cheaper to produce for large scale applications. Among the liquid laser media that are potential candidates for solar pumping, the POC13:Nd(3+):ZrC14 liquid was chosen for its high intrinsic efficiency as well as its relatively good stability against decomposition due to protic contamination. The development and testing of the laser liquid and the development of a large solar concentrator to pump the laser was emphasized. The procedure to manufacture the laser liquid must include diagnostic tests of the solvent purity (from protic contamination) at various stages in the production process

Design and fabrication of noncondensing radiator for environmental evaluation of space power mercury Rankine system

Conceptual and mechanical design analyses, and fabrication of noncondensing radiator for environmental testing of space power mercury Rankine syste

Research on solar pumped liquid lasers

A solar pumped liquid laser that can be scaled up to high power (10 mW CW) for space applications was developed. Liquid lasers have the advantage over gases in that they provide much higher lasant densities and thus high-power densities. Liquids also have advantages over solids in that they have much higher damage thresholds and are much cheaper to produce for large scale applications. Among the liquid laser media that are potential candidates for solar pumping, the POC13: Nd sup 3+:ZrC14 liquid was chosen for its high intrinsic efficiency and its relatively good stability against decomposition due to protic contamination. The development of a manufacturing procedure and performance testing of the laser, liquid and the development of an inexpensive large solar concentrator to pump the laser are examined

A second-order class-D audio amplifier

Class-D audio amplifiers are particularly efficient, and this efficiency has led to their ubiquity in a wide range of modern electronic appliances. Their output takes the form of a high-frequency square wave whose duty cycle (ratio of on-time to off-time) is modulated at low frequency according to the audio signal. A mathematical model is developed here for a second-order class-D amplifier design (i.e., containing one second-order integrator) with negative feedback. We derive exact expressions for the dominant distortion terms, corresponding to a general audio input signal, and confirm these predictions with simulations. We also show how the observed phenomenon of “pulse skipping” arises from an instability of the analytical solution upon which the distortion calculations are based, and we provide predictions of the circumstances under which pulse skipping will take place, based on a stability analysis. These predictions are confirmed by simulations