Properties of large area ErBa2Cu3O(7-x) thin films deposited by ionized cluster beams

ErBa2Cu3O(7-x) films have been produced by simultaneous deposition of Er, Ba, and Cu from three ionized cluster beam (ICB) sources at acceleration voltages of 0.3 to 0.5 kV. Combining ozone oxidation with ICB deposition at 650 C eliminated any need of post annealing processing. The substrates were rotated at 10 rotations per minute during the deposition which took place at a rate of about 3 to 4 nm. Films with areas up to 70 mm in diameter have been made by ICB deposition. These films, 100 nm thick, were deposited on SrTiO3 (100) substrates at 650 C in a mixture of six percent O3 in O2 at a total pressure of 4 x 10(exp -4) Torr. They had T(sub c) ranging from 84.3 K to 86.8 K over a 70 mm diameter and J(sub c) above 10(exp 6) A/sq cm at 77 K. X ray diffraction measurements of the three samples showed preferential c-axis orientation normal to the substrate surface. Scanning electron micrographs (SEM) of the three samples also show some texture dependence on sample position. For the three samples, there is a correlation between SEM texture, full width at half-maximum of rocking curves and J(sub c) versus temperature curves

Comparison of Pressurized and Gravity Distribution Systems for Wastewater Treatment

Pressurized distribution of domestic wastewater over a sand filter surface achieves better treatment than gravity distribution. The pressurized distribution system caused the filter to better remove organics (BOD₅) and suspended solids. Pressurized distribution also caused the sand filter to achieve more complete nitrification than the filter having gravity distribution. Two slow sand filters 15.2 cm wide, 3.1 m long and 15.2 cm deep were built and loaded with domestic septic tank effluent for 250 days at a rate of 5.1 cm per day. Influent and effluent samples were collected and analyzed for five-day Biochemical Oxygen Demand (BOD₅), suspended solids, ammonia- nitrogen, and nitrate-nitrogen. One filter received septic tank effluent through a 10 cm nominal diameter PVC perforated pipe viaa distribution box dosed by a pump with gravity flow from the distribution box to the pipe. The other filter received water through a 2.5 cm nominal diameter PVC pipe having 0.4 cm diameter holes drilled 76.2 cm on center. The gravity distribution filter system achieved mean effluent values of 36.4 mg// BOD₅ , 19.8 mg// suspended solids, 37.6 mg// ammonia-nitrogen, and 46.6 mg// nitrate-nitrogen. The pressurized distribution system achieved 19.1 mg// BOD₅\u3e 12.2 mg// suspended solids, 25.3 mg// ammonia-nitrogen, and 64.03 mg// nitrate-nitrogen. Influent to the filters averaged 132.1 mg// , 90.3 mg//, 70.3 mg// , and 3.6 mg// BOD₅ , suspended solids, ammonia-nitrogen, and nitrate- nitrogen, respectively

Process of making thin film 2H .alpha.-sic by laser ablation

Thin films of 2H .alpha.-silicon carbide are produced by pulsed laser ablation

Simulation and measurement of transcranial near infrared light penetration

We are studying the transmission of LED array-emitted near-infrared (NIR) light through human tissues. Herein, we simulated and measured transcranial NIR penetration in highly scattering human head tissues. Using finite element analysis, we simulated photon diffusion in a multilayered 3D human head model that consists of scalp, skull, cerebral spinal fluid, gray matter and white matter. The optical properties of each layer, namely scattering and absorption coefficient, correspond to the 850 nm NIR light. The geometry of the model is minimally modified from the IEEE standard and the multiple LED emitters in an array were evenly distributed on the scalp. Our results show that photon distribution produced by the array exhibits little variation at similar brain depth, suggesting that due to strong scattering effects of the tissues, discrete spatial arrangements of LED emitters in an array has the potential to create a quasi-radially symmetrical illumination field. Measurements on cadaveric human head tissues excised from occipital, parietal, frontal and temporal regions show that illumination with an 850 nm LED emitter rendered a photon flux that closely follows simulation results. In addition, prolonged illumination of LED emitted NIR showed minimal thermal effects on the brain

Cloud Atlas: Rotational Spectral Modulations and potential Sulfide Clouds in the Planetary-mass, Late T-type Companion Ross 458C

Measurements of photometric variability at different wavelengths provide insights into the vertical cloud structure of brown dwarfs and planetary-mass objects. In seven Hubble Space Telescope consecutive orbits, spanning $\sim$10 h of observing time}, we obtained time-resolved spectroscopy of the planetary-mass T8-dwarf Ross 458C using the near-infrared Wide Field Camera 3. We found spectrophotometric variability with a peak-to-peak signal of 2.62$\pm$0.02 % (in the 1.10-1.60~$\mu$m white light curve). Using three different methods, we estimated a rotational period of 6.75$\pm$1.58~h for the white light curve, and similar periods for narrow $J$- and $H$- band light curves. Sine wave fits to the narrow $J$- and $H$-band light curves suggest a tentative phase shift between the light curves with wavelength when we allow different periods between both light curves. If confirmed, this phase shift may be similar to the phase shift detected earlier for the T6.5 spectral type 2MASS J22282889-310262. We find that, in contrast with 2M2228, the variability of Ross~458C shows evidence for a {color trend} within the narrow $J$-band, but gray variations in the narrow $H$-band. The spectral time-resolved variability of Ross 458C might be potentially due to heterogeneous sulfide clouds in the atmosphere of the object. Our discovery extends the study of spectral modulations of condensate clouds to the coolest T dwarfs, planetary-mass companions.Comment: Accepted in ApJ

Cloud Atlas: Discovery of Rotational Spectral Modulations in a Low-mass, L-type Brown Dwarf Companion to a Star

Observations of rotational modulations of brown dwarfs and giant exoplanets allow the characterization of condensate cloud properties. As of now rotational spectral modulations have only been seen in three L-type brown dwarfs. We report here the discovery of rotational spectral modulations in LP261-75B, an L6-type intermediate surface gravity companion to an M4.5 star. As a part of the Cloud Atlas Treasury program we acquired time-resolved Wide Field Camera 3 grism spectroscopy (1.1--1.69~$\mu$m) of LP261-75B. We find gray spectral variations with the relative amplitude displaying only a weak wavelength dependence and no evidence for lower-amplitude modulations in the 1.4~$\mu$m water band than in the adjacent continuum. The likely rotational modulation period is 4.78$\pm$0.95 h, although the rotational phase is not well sampled. The minimum relative amplitude in the white light curve measured over the whole wavelength range is 2.41$\pm$0.14\%. We report an unusual light curve with seemingly three peaks approximately evenly distributed in rotational phase. The spectral modulations suggests that the upper atmosphere cloud properties in {LP261-75B} are similar to two other mid-L dwarfs of typical infrared colors, but differ from that of the extremely red L-dwarf WISE0047

Simple, Defensible Sample Sizes Based on Cost Efficiency -- With Discussion and Rejoinder

The conventional approach of choosing sample size to provide 80% or greater power ignores the cost implications of different sample size choices. Costs, however, are often impossible for investigators and funders to ignore in actual practice. Here, we propose and justify a new approach for choosing sample size based on cost efficiency, the ratio of a study’s projected scientific and/or practical value to its total cost. By showing that a study’s projected value exhibits diminishing marginal returns as a function of increasing sample size for a wide variety of definitions of study value, we are able to develop two simple choices that can be defended as more cost efficient than any larger sample size. The first is to choose the sample size that minimizes the average cost per subject. The second is to choose sample size to minimize total cost divided by the square root of sample size. This latter method is theoretically more justifiable for innovative studies, but also performs reasonably well and has some justification in other cases. For example, if projected study value is assumed to be proportional to power at a specific alternative and total cost is a linear function of sample size, then this approach is guaranteed either to produce more than 90% power or to be more cost efficient than any sample size that does. These methods are easy to implement, based on reliable inputs, and well justified, so they should be regarded as acceptable alternatives to current conventional approaches

Selective inhibition of FLT3 by gilteritinib in relapsed or refractory acute myeloid leukaemia: a multicentre, first-in-human, open-label, phase 1-2 study.

BackgroundInternal tandem duplication mutations in FLT3 are common in acute myeloid leukaemia and are associated with rapid relapse and short overall survival. The clinical benefit of FLT3 inhibitors in patients with acute myeloid leukaemia has been limited by rapid generation of resistance mutations, particularly in codon Asp835 (D835). We aimed to assess the highly selective oral FLT3 inhibitor gilteritinib in patients with relapsed or refractory acute myeloid leukaemia.MethodsIn this phase 1-2 trial, we enrolled patients aged 18 years or older with acute myeloid leukaemia who either were refractory to induction therapy or had relapsed after achieving remission with previous treatment. Patients were enrolled into one of seven dose-escalation or dose-expansion cohorts assigned to receive once-daily doses of oral gilteritinib (20 mg, 40 mg, 80 mg, 120 mg, 200 mg, 300 mg, or 450 mg). Cohort expansion was based on safety and tolerability, FLT3 inhibition in correlative assays, and antileukaemic activity. Although the presence of an FLT3 mutation was not an inclusion criterion, we required ten or more patients with locally confirmed FLT3 mutations (FLT3mut+) to be enrolled in expansion cohorts at each dose level. On the basis of emerging findings, we further expanded the 120 mg and 200 mg dose cohorts to include FLT3mut+ patients only. The primary endpoints were the safety, tolerability, and pharmacokinetics of gilteritinib. Safety and tolerability were assessed in the safety analysis set (all patients who received at least one dose of gilteritinib). Responses were assessed in the full analysis set (all patients who received at least one dose of study drug and who had at least one datapoint post-treatment). Pharmacokinetics were assessed in a subset of the safety analysis set for which sufficient data for concentrations of gilteritinib in plasma were available to enable derivation of one or more pharmacokinetic variables. This study is registered with ClinicalTrials.gov, number NCT02014558, and is ongoing.FindingsBetween Oct 15, 2013, and Aug 27, 2015, 252 adults with relapsed or refractory acute myeloid leukaemia received oral gilteritinib once daily in one of seven dose-escalation (n=23) or dose-expansion (n=229) cohorts. Gilteritinib was well tolerated; the maximum tolerated dose was established as 300 mg/day when two of three patients enrolled in the 450 mg dose-escalation cohort had two dose-limiting toxicities (grade 3 diarrhoea and grade 3 elevated aspartate aminotransferase). The most common grade 3-4 adverse events irrespective of relation to treatment were febrile neutropenia (97 [39%] of 252), anaemia (61 [24%]), thrombocytopenia (33 [13%]), sepsis (28 [11%]), and pneumonia (27 [11%]). Commonly reported treatment-related adverse events were diarrhoea (92 [37%] of 252]), anaemia (86 [34%]), fatigue (83 [33%]), elevated aspartate aminotransferase (65 [26%]), and increased alanine aminotransferase (47 [19%]). Serious adverse events occurring in 5% or more of patients were febrile neutropenia (98 [39%] of 252; five related to treatment), progressive disease (43 [17%]), sepsis (36 [14%]; two related to treatment), pneumonia (27 [11%]), acute renal failure (25 [10%]; five related to treatment), pyrexia (21 [8%]; three related to treatment), bacteraemia (14 [6%]; one related to treatment), and respiratory failure (14 [6%]). 95 people died in the safety analysis set, of which seven deaths were judged possibly or probably related to treatment (pulmonary embolism [200 mg/day], respiratory failure [120 mg/day], haemoptysis [80 mg/day], intracranial haemorrhage [20 mg/day], ventricular fibrillation [120 mg/day], septic shock [80 mg/day], and neutropenia [120 mg/day]). An exposure-related increase in inhibition of FLT3 phosphorylation was noted with increasing concentrations in plasma of gilteritinib. In-vivo inhibition of FLT3 phosphorylation occurred at all dose levels. At least 90% of FLT3 phosphorylation inhibition was seen by day 8 in most patients receiving a daily dose of 80 mg or higher. 100 (40%) of 249 patients in the full analysis set achieved a response, with 19 (8%) achieving complete remission, ten (4%) complete remission with incomplete platelet recovery, 46 (18%) complete remission with incomplete haematological recovery, and 25 (10%) partial remission INTERPRETATION: Gilteritinib had a favourable safety profile and showed consistent FLT3 inhibition in patients with relapsed or refractory acute myeloid leukaemia. These findings confirm that FLT3 is a high-value target for treatment of relapsed or refractory acute myeloid leukaemia; based on activity data, gilteritinib at 120 mg/day is being tested in phase 3 trials.FundingAstellas Pharma, National Cancer Institute (Leukemia Specialized Program of Research Excellence grant), Associazione Italiana Ricerca sul Cancro

Northeastern united states species treated with copper-based preservatives: Durability in mississippi stake tests

This paper reports on the ground-contact durability of lesser-used wood species of the northeastern United States after treatment with copper-based preservatives. Stakes (19 by 19 by 457 mm) cut from balsam-fir (Abies balsamea), eastern hemlock (Tsuga canadensis), eastern spruce (mixture of Picea glauca, Picea mariana and Picea rubens), red maple (Acer rubrum) or eastern white pine (Pinus strobus) were treated with one of four concentrations of chromated copper arsenate type C (CCA-C), copper citrate (CC), alkaline copper quat type C (ACQ-C) or copper azole type A (CBA-A) and placed into the ground at a test site in southern Mississippi. Similarly treated southern pine (Pinus spp.) stakes were included for comparison. The stakes were rated for decay and termite attack after 1, 2, 3, 4, 5, 8, 10 and 12 years. Eastern white pine and incised eastern hemlock and balsam-fir had durability similar to southern pine when treated with CCA or the other copper-based preservatives. Eastern spruce was less durable than the other softwood species, apparently because of low preservative uptake. Red maple had the least durability at all retentions and for all preservatives. This study indicates that several northeastern softwoods can be adequately durable when pressure-treated with CCA-C or copper-based preservatives

Soil carbon, after 3 years, under short-rotation woody crops grown under varying nutrient and water availability.

Abstract Soil carbon contents were measured on a short-rotation woody crop study located on the US Department of Energy’s Savannah River Site outside Aiken, SC. This study included fertilization and irrigation treatments on five tree genotypes (sweetgum, loblolly pine, sycamore and two eastern cottonwood clones). Prior to study installation, the previous pine stand was harvested and the remaining slash and stumps were pulverized and incorporated 30 cm into the soil. One year after harvest soil carbon levels were consistent with preharvest levels but dropped in the third year below pre-harvest levels. Tillage increased soil carbon contents, after three years, as compared with adjacent plots that were not part of the study but where harvested, but not tilled, at the same time. When the soil response to the individual treatments for each genotype was examined, one cottonwood clone (ST66), when irrigated and fertilized, had higher total soil carbon and mineral associated carbon in the upper 30 cm compared with the other tree genotypes. This suggests that root development in ST66 may have been stimulated by the irrigation plus fertilization treatment