Identification of a gene encoding GMP synthetase from a Neurospora crassa cDNA library by bacterial complementation

We report the isolation and identification of a gene encoding GMP synthetase from a Neurospora crassa cDNA library. Phage infection of the purine-requiring Escherichia coli strain SØ3834 using the NO3- induced cDNA phage library from the Fungal Genetics Stock Center resulted in colonies able to grow on minimal media with no added purine source. A plasmid, termed pGMPS1, was isolated from one of these colonies and shown to reproducibly support growth of strain SØ3834 in the absence of purines in the media. Identification of this gene as one encoding GMP synthetase is confirmed by DNA sequencing and comparison to the known guaA gene from yeast

Application of ERTS-1 imagery to state wide land information system in Minnesota

There are no author-identified significant results in this report

Use of Molybdenum in the Transplant Water for Burley Tobacco

The need for adding molybdenum to tobacco arises because contents in Kentucky soils generally are on the borderline of sufficiency and because amounts of available molybdenum in soil are low when soil pH is low. Soil pH in tobacco fields at midseason often is 0.5 to 1.0 pH unit lower than prior to fertilization. primarily because of the high rates of commercial fertilizers commonly applied to tobacco. This acidity greatly lowers the availability of molybdenum to tobacco plants. That is why we recommend the use of molybdenum when soil pH before fertilization is 6.4 or below

Delamination growth in composite materials

The Double Cantilever Beam (DCB) and the End Notched Flexure (ENF) specimens are employed to characterize MODE I and MODE II interlaminar fracture resistance of graphite/epoxy (CYCOM 982) and graphite/PEEK (APC2) composites. Sizing of test specimen geometries to achieve crack growth in the linear elastic regime is presented. Data reduction schemes based upon beam theory are derived for the ENF specimen and include the effects of shear deformation and friction between crack surfaces on compliance, C, and strain energy release rate, G sub II. Finite element (FE) analyses of the ENF geometry including the contact problem with friction are presented to assess the accuracy of beam theory expressions for C and G sub II. Virtual crack closure techniques verify that the ENF specimen is a pure Mode II test. Beam theory expressions are shown to be conservative by 20 to 40 percent for typical unidirectional test specimen geometries. A FE parametric study investigating the influence of delamination length and depth, span, thickness and material properties on G sub II is presented. Mode I and II interlaminar fracture test results are presented. Important experimental parameters are isolated, such as precracking techniques, rate effects, and nonlinear load-deflection response. It is found that subcritical crack growth and inelastic materials behavior, responsible for the observed nonlinearities, are highly rate-dependent phenomena with high rates generally leading to linear elastic response

Delamination growth in composite materials

Research related to growth of an imbedded through-width delamination (ITWD) in a compression loaded composite structural element is presented. Composites with widely different interlaminar fracture resistance were examined, viz., graphite/epoxy (CYCOM 982) and graphite/PEEK (APC-2). The initial part of the program consisted of characterizing the material in tension, compression and shear mainly to obtain consistent material properties for analysis, but also as a check of the processing method developed for the thermoplastic APC-2 material. The characterization of the delamination growth in the ITWD specimen, which for the unidirectional case is essentially a mixed Mode 1 and 2 geometry, requires verified mixed-mode growth criteria for the two materials involved. For this purpose the main emphasis during this part of the investigation was on Mode 1 and 2 fracture specimens, namely the Double Cantilever Beam (DCB) and End Notched Flexure (ENF) specimens

The Detector System for the Stratospheric Kinetic Inductance Polarimeter (SKIP)

The Stratospheric Kinetic Inductance Polarimeter (SKIP) is a proposed balloon-borne experiment designed to study the cosmic microwave background, the cosmic infrared background and Galactic dust emission by observing 1133 square degrees of sky in the Northern Hemisphere with launches from Kiruna, Sweden. The instrument contains 2317 single-polarization, horn-coupled, aluminum lumped-element kinetic inductance detectors (LEKID). The LEKIDs will be maintained at 100 mK with an adiabatic demagnetization refrigerator. The polarimeter operates in two configurations, one sensitive to a spectral band centered on 150 GHz and the other sensitive to 260 and 350 GHz bands. The detector readout system is based on the ROACH-1 board, and the detectors will be biased below 300 MHz. The detector array is fed by an F/2.4 crossed-Dragone telescope with a 500 mm aperture yielding a 15 arcmin FWHM beam at 150 GHz. To minimize detector loading and maximize sensitivity, the entire optical system will be cooled to 1 K. Linearly polarized sky signals will be modulated with a metal-mesh half-wave plate that is mounted at the telescope aperture and rotated by a superconducting magnetic bearing. The observation program consists of at least two, five-day flights beginning with the 150 GHz observations.Comment: J Low Temp Phys DOI 10.1007/s10909-013-1014-3 The final publication is available at link.springer.co