1,098 research outputs found
Comparative analysis of alternative fuels in detonation combustion
Detonation combustion prominently exhibits high thermodynamic efficiency which leads to better performance. As compared to the conventionally used isobaric heat addition in a Brayton cycle combustor, detonation uses a novel isochoric Humphrey cycle which utilises shocks and detonation waves to provide pressure-rise combustion. Such unsteady combustion has already been explored in wave rotor, pulse detonation engine and rotating detonation engine configurations as alternative technologies for the next generation of the aerospace propulsion systems. However, in addition to the better performance that the detonation mode of combustion offers, it is crucial to observe the environmental concerns as well. Therefore, this paper presents a one-dimensional numerical analysis for alternative fuels: Jet-A, Acetylene, Jatropha Bio-synthetic Paraffinic Kerosene, Camelina Bio-synthetic Paraffinic Kerosene, Algae Biofuel, and Microalgae Biofuel under detonation combustion conditions. For simplicity, the analysis is modelled using an open tube geometry. The analysis employs the Rankine-Hugoniot Equation, Rayleigh Line Equation, and Zel’dovich–von Neumann–Doering model and takes into account species mole, mass fraction, and enthalpies-of-formation of the reactants. Initially, minimum conditions for the detonation of each fuel are determined. Pressure, temperature, and density ratios at each stage of the combustion tube for different types of fuel are then explored systematically. Finally, the influence of different initial conditions is numerically examined to make a comparison for these fuels
Electrical power grid network optimisation by evolutionary computing
A major factor in the consideration of an electrical power network of the scale of a national grid is the calculation of power flow and in particular, optimal power flow. This paper considers such a network, in which distributed generation is used, and examines how the network can be optimized, in terms of transmission line capacity, in order to obtain optimal or at least high-performing configurations, using multi-objective optimisation by evolutionary computing methods
Integrated system to perform surrogate based aerodynamic optimisation for high-lift airfoil
This work deals with the aerodynamics optimisation of a generic two-dimensional three element high-lift configuration. Although the high-lift system is applied only during take-off and landing in the low speed phase of the flight the cost efficiency of the airplane is strongly influenced by it [1]. The ultimate goal of an aircraft high lift system design team is to define the simplest configuration which, for prescribed constraints, will meet the take-off, climb, and landing requirements usually expressed in terms of maximum L/D and/or maximum CL. The ability of the calculation method to accurately predict changes in objective function value when gaps, overlaps and element deflections are varied is therefore critical. Despite advances in computer capacity, the enormous computational cost of running complex engineering simulations makes it impractical to rely exclusively on simulation for the purpose of design optimisation. To cut down the cost, surrogate models, also known as metamodels, are constructed from and then used in place of the actual simulation models. This work outlines the development of integrated systems to perform aerodynamics multi-objective optimisation for a three-element airfoil test case in high lift configuration, making use of surrogate models available in MACROS Generic Tools, which has been integrated in our design tool. Different metamodeling techniques have been compared based on multiple performance criteria. With MACROS is possible performing either optimisation of the model built with predefined training sample (GSO) or Iterative Surrogate-Based Optimization (SBO). In this first case the model is build independent from the optimisation and then use it as a black box in the optimisation process. In the second case is needed to provide the possibility to call CFD code from the optimisation process, and there is no need to build any model, it is being built internally during the optimisation process. Both approaches have been applied. A detailed analysis of the integrated design system, the methods as well as th
Modelling of spray evaporation and penetration for alternative fuels
The focus of this work is on the modelling of evaporation and spray penetration for alternative fuels. The extension model approach is presented and validated for alternative fuels, namely, Kerosene (KE), Ethanol (ETH), Methanol (MTH), Microalgae biofuel (MA), Jatropha biofuel (JA), and Camelina biofuel (CA). The results for atomization and spray penetration are shown in a time variant condition. Comparisons have been made to visualize the transient behaviour of these fuels. The vapour pressure tendencies are revealed to have significant effects on the transient shape of the evaporation process. In a given time frame, ethanol fuel exhibits the highest evaporation rate and followed by methanol, other biofuels and kerosene. Ethanol also propagates the farthest distance and followed by methanol and kerosene. However, all biofuels have a shorter penetration length in the given time. These give penalty costs to biofuels emissions formation. The influences of initial conditions such as temperature and droplet velocity are also explored numerically. High initial temperature and velocity could accelerate evaporation rate. However, high initial temperature has resulted in low penetration length while high initial velocity produces contrasting results
Comparative study of alternative biofuels on aircraft engine performance
Aviation industries are vulnerable to the energy crisis and simultaneously posed environmental concerns. Proposed engine technology advancements could reduce the environmental impact and energy consumption. Substituting the source of jet fuel from fossil-based fuel to biomass-based fuel will help reduce emissions and minimize the energy crisis. The present paper addresses the analysis of aircraft engine performance in terms of thrust, fuel flow and specific fuel consumption at different mixing ratio percentages (20%, 40%, 50%, 60% and 80%) of alternative biofuel blends already used in flight test (Algae biofuel, Camelina biofuel and Jatropha biofuel) at different flight conditions. In-house computer software codes, PYTHIA and TURBOMATCH, were used for the analysis and modeling of a three-shaft high-bypass-ratio engine which is similar to RB211-524. The engine model was verified and validated with open literature found in the test program of bio-synthetic paraffinic kerosene in commercial aircraft. The results indicated that lower heating value had a significant influence on thrust, fuel flow and specific fuel consumption at every flight condition and at all mixing ratio percentages. Wide lower heating value differences between two fuels give a large variation on the engine performances. Blended Kerosene–Jatropha biofuel and Kerosene–Camelina biofuel showed an improvement on gross thrust, net thrust, reduction of fuel flow and specific fuel consumption at every mixing ratio percentage and at different flight conditions. Moreover, the pure alternative of Jatropha biofuel and Camelina biofuel gave much better engine performances. This was not the case for the Kerosene–Algae blended biofuel. This study is a crucial step in understanding the influence of different blended alternative biofuels on the performance of aircraft engines
Wall-resolved large eddy simulation for aeroengine aeroacoustic investigation
The work presented here forms part of a larger project on Large-Eddy Simulation (LES) of aeroengine aeroacoustic interactions. In this paper, we concentrate on LES of near-field flow over an isolated NACA0012 aerofoil at zero angle-of-attack and a chord based Reynolds number of Rec = 2 × 105. A wall-resolved compressible Numerical Large Eddy Simulation (NLES) approach is employed to resolve streak-like structures in the near-wall flow regions. The calculated unsteady pressure/velocity field will be imported into an analyticallybased scheme for far-field trailing-edge noise prediction later. The boundary-layer mean and root-mean-square (rms) velocity profiles, the surface pressure fluctuation over the aerofoil, and the wake flow development are compared with experimental data and previous computational simulations in our research group. It is found that the results from the wall-resolved compressible NLES are very encouraging as they correlate well with test data. The main features of the wall-resolved compressible NLES, as well as the advantages of such compressible NLES over previous incompressible LES performed in our research group, are also discussed.
This paper will be presented at the ISABE 2017 Conference, 5-8 September 2017, Manchester, UK
An investigation of higher-order multi-objective optimisation for 3D aerodynamic shape design
We investigate the performance of different variants of a suitably tailored Tabu Search optimisation algorithm on a higher-order design problem. We consider four objective func- tions to describe the performance of a compressor stator row, subject to a number of equality and inequality constraints. The same design problem has been previously in- vestigated through single-, bi- and three-objective optimisation studies. However, in this study we explore the capabilities of enhanced variants of our Multi-objective Tabu Search (MOTS) optimisation algorithm in the context of detailed 3D aerodynamic shape design. It is shown that with these enhancements to the local search of the MOTS algorithm we can achieve a rapid exploration of complicated design spaces, but there is a trade-off be- tween speed and the quality of the trade-off surface found. Rapidly explored design spaces reveal the extremes of the objective functions, but the compromise optimum areas are not very well explored. However, there are ways to adapt the behaviour of the optimiser and maintain both a very efficient rate of progress towards the global optimum Pareto front and a healthy number of design configurations lying on the trade-off surface and exploring the compromise optimum regions. These compromise solutions almost always represent the best qualitative balance between the objectives under consideration. Such enhancements to the effectiveness of design space exploration make engineering design optimisation with multiple objectives and robustness criteria ever more practicable and attractive for modern advanced engineering design. Finally, new research questions are addressed that highlight the trade-offs between intelligence in optimisation algorithms and acquisition of qualita- tive information through computational engineering design processes that reveal patterns and relations between design parameters and objective functions, but also speed versus optimum quality
Impact of Fluid Substitution on the Performance of an Axial Compressor Blade Cascade Working with Supercritical Carbon Dioxide
Abstract
Recent research on turbomachinery design and analysis for supercritical carbon dioxide (sCO2) power cycles has relied on computational fluid dynamics. This has produced a large number of works whose approach is mostly case-specific, rather than of general application to sCO2 turbomachinery design. As opposed to such approach, this work explores the aerodynamic performance of compressor blade cascades operating on air and supercritical CO2 with the main objective to evaluate the usual aerodynamic parameters of the cascade for variable boundary conditions and geometries, enabling “full” or “partial” similarity. The results present both the global performance of the cascades and certain features of the local flow (trailing edge and wake). The discussion also highlights the mechanical limitations of the analysis (forces exerted on the blades), which is the main restriction for applying similarity laws to extrapolate the experience gained through decades of work on air turbomachinery to the new working fluid. This approach is a step toward the understanding and appropriate formulation of a multi-objective optimization problem for the design of such turbomachinery components where sCO2 is used as the operating fluid. With this objective, the paper aims to identify and analyze what would be expected if a common description of such computational design problems similar to those where air is the working fluid were used.</jats:p
Explaining Observed Infection and Antibody Age-Profiles in Populations with Urogenital Schistosomiasis
Urogenital schistosomiasis is a tropical disease infecting more than 100 million people in sub-Saharan Africa. Individuals in endemic areas endure repeated infections with long-lived schistosome worms, and also encounter larval and egg stages of the life cycle. Protective immunity against infection develops slowly with age. Distinctive age-related patterns of infection and specific antibody responses are seen in endemic areas, including an infection ‘peak shift’ and a switch in the antibody types produced. Deterministic models describing changing levels of infection and antibody with age in homogeneously exposed populations were developed to identify the key mechanisms underlying the antibody switch, and to test two theories for the slow development of protective immunity: that (i) exposure to dying (long-lived) worms, or (ii) experience of a threshold level of antigen, is necessary to stimulate protective antibody. Different model structures were explored, including alternative stages of the life cycle as the main antigenic source and the principal target of protective antibody, different worm survival distributions, antigen thresholds and immune cross-regulation. Models were identified which could reproduce patterns of infection and antibody consistent with field data. Models with dying worms as the main source of protective antigen could reproduce all of these patterns, but so could some models with other continually-encountered life stages acting as the principal antigen source. An antigen threshold enhanced the ability of the model to replicate these patterns, but was not essential for it to do so. Models including either non-exponential worm survival or cross-regulation were more likely to be able to reproduce field patterns, but neither of these was absolutely required. The combination of life cycle stage stimulating, and targeted by, antibody was found to be critical in determining whether models could successfully reproduce patterns in the data, and a number of combinations were excluded as being inconsistent with field data
Evaluation of risks of foot-and-mouth disease in Scotland to assist with decision making during the 2007 outbreak in the UK
An outbreak of foot-and-mouth disease (FMD) occurred in Surrey on August 3, 2007. A Great Britain-wide ban on livestock movements was implemented immediately. This coincided with the start of seasonal sheep movements off the hills in Scotland; the majority of these animals are sold via markets. The ban therefore posed severe economic and animal-welfare hardships if it was to last through September and beyond. The Scottish Government commissioned an analysis to assess the risk of re-opening markets given the uncertainty about whether FMD had entered Scotland. Tracing of livestock moved from within the risk zone in England between July 16 and August 3 identified contact chains to 12 Scottish premises; veterinary field inspections found a further three unrecorded movements. No signs of infection were found on these holdings. Under the conservative assumption that a single unknown Scottish holding was infected with FMD, an estimate of the time-dependent probability of Scotland being FMD free given no detection was made. Analyses indicated that if FMD was not detected by early to mid-September then it was highly probable that Scotland was FMD free. Risk maps were produced to visualise the potential spread of FMD across Scotland if it was to spread either locally or via market sales
- …