Fluid pumped by magnetic stress

A magnetic field rotating on the free surface of a ferrofluid layer is shown to induce considerable fluid motion toward the direction the field is rolling. The measured flow velocity i) increases with the square of the magnetic field amplitude, ii) is proportional to the thickness of the fluid layer, and iii) has a maximum at a driving frequency of about 3 kHz. The pumping speed can be estimated with a two-dimensional flow model.Comment: 3 pages, 4 figure

Hexagons become second if symmetry is broken

Pattern formation on the free surface of a magnetic fluid subjected to a magnetic field is investigated experimentally. By tilting the magnetic field the symmetry can be broken in a controllable manner. When increasing the amplitude of the tilted field, the flat surface gives way to liquid ridges. A further increase results in a hysteretic transition to a pattern of stretched hexagons. The instabilities are detected by means of a linear array of magnetic hall sensors and compared with theoretical predictions.Comment: accepted for publication by Physical Review E/Rapid Communicatio

Wave Number of Maximal Growth in Viscous Magnetic Fluids of Arbitrary Depth

An analytical method within the frame of linear stability theory is presented for the normal field instability in magnetic fluids. It allows to calculate the maximal growth rate and the corresponding wave number for any combination of thickness and viscosity of the fluid. Applying this method to magnetic fluids of finite depth, these results are quantitatively compared to the wave number of the transient pattern observed experimentally after a jump--like increase of the field. The wave number grows linearly with increasing induction where the theoretical and the experimental data agree well. Thereby a long-standing controversy about the behaviour of the wave number above the critical magnetic field is tackled.Comment: 19 pages, 15 figures, RevTex; revised version with a new figure and references added. submitted to Phys Rev

Friction behavior and other material properties of nickel-titanium and titanium-molybdenum archwires following electrochemical surface refinement

The aim of this work was to investigate whether electrochemical surface treatment of nickel-titanium (NiTi) and titanium-molybdenum (TiMo) archwires (OptoTherm (TM) and BetaTitan (TM); Ortho-Dent Specials, Kisdorf, Germany) reduces friction inside the bracket-archwire complex. We also evaluated further material properties and compared these to untreated wires. The material properties of the surface-treated wires (Optotherm/LoFrix (TM) and BetaTitan/LoFrix (TM)) were compared to untreated wires made by the same manufacturer (see above) and by another manufacturer (Neo SentalloyA (R); GAC, Bohemia, NY, USA). We carried out a three-point bending test, leveling test, and friction test using an orthodontic measurement and simulation system (OMSS). In addition, a pure bending test was conducted at a special test station, and scanning electron micrographs were obtained to analyze the various wire types for surface characteristics. Finally, edge beveling and cross-sectional dimensions were assessed. Force losses due to friction were reduced by 10 percentage points (from 36 to 26%) in the NiTi and by 12 percentage points (from 59 to 47%) in the TiMo wire specimens. Most of the other material properties exhibited no significant changes after surface treatment. While the three-point bending tests revealed mildly reduced force levels in the TiMo specimens due to diameter losses of roughly 2%, these force levels remained almost unchanged in the NiTi specimens. Compared to untreated NiTi and TiMo archwire specimens, the surface-treated specimens demonstrated reductions in friction loss by 10 and 12 percentage points, respectively

Bionic tactile sensor for near-range search, localisation and material classification

Dürr V, Krause AF, Neitzel M, Lange O, Reimann B. Bionic tactile sensor for near-range search, localisation and material classification. In: Berns K, Luksch T, eds. Autonome Mobile Systeme 2007, 20. Fachgespräch Kaiserslautern, 18./19. Oktober 2007. Heidelberg: Springer; 2007: 240-246