14,450 research outputs found
Structural perfection in poorly lattice matched heterostructures
Continuum elastic theory is applied to the formation of misfit dislocations and point defects in strained layer structures. Explicit calculations of the energies of misfit dislocations in the double‐ and single‐kink geometries yield line tensions below which strained films are stable with respect to defect formation. Our results yield a mismatch‐dependent stability limit which, in the double kink case, differs from the Matthews–Blakeslee model by a geometrical factor and by the addition of a stress term associated with climb of the misfit dislocation. While our calculations yield equilibrium stability limits which may not correspond to observed critical thicknesses, the calculated stresses may be applied to descriptions of the kinetics of strain relief in films grown beyond these limits. Last, calculations of strain‐related contributions to the free energy of formation of point defects suggest a contribution │ΔG_(strain)│ ≃0.25 eV for a 5% lattice mismatch. This suggests a means of suppressing or enhancing the formation of vacancies or interstitials in semiconductors favoring these defects
Effects of forward velocity on noise for a J85 turbojet engine with multitube suppressor from wind tunnel and flight tests
Flight and wind tunnel noise tests were conducted using a J85 turbojet engine as a part of comprehensive programs to obtain an understanding of forward velocity effects on jet exhaust noise. Nozzle configurations of primary interest were a 104-tube suppressor with and without an acoustically-treated shroud. The installed configuration of the engine was as similar as possible in the flight and wind tunnel tests. Exact simultaneous matching of engine speed, exhaust velocity, and exhaust temperature was not possible, and the wind tunnel maximum Mach number was approximately 0.27, while the flight Mach number was approximately 0.37. The nominal jet velocity range was 450 to 640 m/sec. For both experiments, background noise limited the jet velocity range for which significant data could be obtained. In the present tests the observed directivity and forward velocity effects for the suppressor are more similar to predicted trends for internally-generated noise than unsuppressed jet noise
Spaceborne power systems preference analyses. Volume 2: Decision analysis
Sixteen alternative spaceborne nuclear power system concepts were ranked using multiattribute decision analysis. The purpose of the ranking was to identify promising concepts for further technology development and the issues associated with such development. Four groups were interviewed to obtain preference. The four groups were: safety, systems definition and design, technology assessment, and mission analysis. The highest ranked systems were the heat-pipe thermoelectric systems, heat-pipe Stirling, in-core thermionic, and liquid-metal thermoelectric systems. The next group contained the liquid-metal Stirling, heat-pipe Alkali Metal Thermoelectric Converter (AMTEC), heat-pipe Brayton, liquid-metal out-of-core thermionic, and heat-pipe Rankine systems. The least preferred systems were the liquid-metal AMTEC, heat-pipe thermophotovoltaic, liquid-metal Brayton and Rankine, and gas-cooled Brayton. The three nonheat-pipe technologies selected matched the top three nonheat-pipe systems ranked by this study
Spaceborne power systems preference analyses. Volume 1: Summary
Sixteen alternative spaceborne nuclear power system concepts were ranked using multiattribute decision analysis to identify promising concepts for further technology development. Four groups interviewed were: safety, systems definition and design, technology assessment, and mission analysis. The ranking results were consistent from group and for different utility function models for individuals
Noise produced by a small-scale, externally blown flap
Noise data were obtained with a model of an externally blown flap of the type that is currently being considered for STOL aircraft. The noise caused by impingement of the jet on the flap is much louder than the nozzle jet noise. It is especially so directly below the wing. The noise level increases as the jet velocity and flap angle are increased. The sound power level increased with the sixth power of velocity. Several physical variations to the STOL model configuration were also tested. Two such variations, a large board and a slotless curved plate wing, had the same power spectra density (Strouhal number curve) as the model
Type II superlattices for infrared detectors and devices
Superlattices consisting of combinations of III-V semiconductors with type II band alignments are of interest for infrared applications because their energy gaps can be made smaller than those of any 'natural' III-V compounds. Specifically, it has been demonstrated that both InSb/InAsxSb1-x superlattices and Ga1-xInxSb/InAs superlattices can possess energy gaps in the 8-14 mu m range. The efforts have focused on the Ga1-xInxSb/InAs system because of its extreme broken gap band alignment, which results in narrow energy gaps for very short superlattice periods. The authors report the use of in situ chemical doping of Ga1-xInxSb/InAs superlattices to fabricate p-n photodiodes. These diodes display a clear photovoltaic response with a threshold near 12 mu m. They have also attained outstanding structural quality in Ga1-xInxSb/InAs superlattices grown on radiatively heated GaSb substrates. Cross-sectional transmission electron microscope images of these superlattices display no dislocations, while high resolution X-ray diffraction scans reveal sharp high-order superlattice satellites and strong Pendellosung fringes
Structure of CdTe/ZnTe superlattices
The structure of CdTe/ZnTe superlattices has been analyzed through θ/2θ x‐ray diffraction, photoluminescence, and in situ reflection high‐energy electron diffraction (RHEED) measurements. Samples are found to break away from Cd_(x)Zn_(1−x)Te buffer layers as a consequence of the 6% lattice mismatch in this system. However, defect densities in these superlattices are seen to drop dramatically away from the buffer layer interface, accounting for the intense photoluminescence and high‐average strain fields seen in each of our samples. Observed variations in residual strains suggest that growth conditions play a role in forming misfit defects. This could explain discrepancies with calculated values of critical thickness based on models which neglect growth conditions. Photoluminescence spectra reveal that layer‐to‐layer growth proceeded with single monolayer uniformity, suggesting highly reproducible growth. Our results give hope for relatively defect‐free Cd_(x)Zn_(1−x)Te/Cd_(y)Zn_(1−y)Te superlattices with the potential for applications to optoelectronics offered by intense visible light emitters
Integrated circuit cell library
According to the invention, an ASIC cell library for use in creation of custom integrated circuits is disclosed. The ASIC cell library includes some first cells and some second cells. Each of the second cells includes two or more kernel cells. The ASIC cell library is at least 5% comprised of second cells. In various embodiments, the ASIC cell library could be 10% or more, 20% or more, 30% or more, 40% or more, 50% or more, 60% or more, 70% or more, 80% or more, 90% or more, or 95% or more comprised of second cells
- …